This DTC is stored when a malfunction occurs in the speakers.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15C3 | A short is detected in the speaker output circuit. | ·
Speakers ·
Harness or connector ·
Stereo component amplifier assembly (except 4 speakers) ·
Navigation receiver assembly |
Clear the DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).
No DTCs are output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Check the vehicle condition.
| Result | Proceed to |
|---|---|
| for 4 Speakers | A |
| for 7 or 9 Speakers | B |
| for 12 Speakers | C |
A
B
C
*1: for RH Side
*2: for LH Side
Disconnect the J133 navigation receiver assembly connector.
Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.
Disconnect the J147*1 and/or J149*2 front No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J133-1 (FR+) - J147-3 (TWR+) | Always | Below 1 Ω |
| J133-5 (FR-) - J147-2 (TWR-) | Always | Below 1 Ω |
| M8-1 - J147-1 (+) | Always | Below 1 Ω |
| M8-2 - J147-4 (-) | Always | Below 1 Ω |
| J133-2 (FL+) - J149-3 (TWL+) | Always | Below 1 Ω |
| J133-6 (FL-) - J149-2 (TWL-) | Always | Below 1 Ω |
| N10-1 - J149-1 (+) | Always | Below 1 Ω |
| N10-2 - J149-4 (-) | Always | Below 1 Ω |
| J133-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| J133-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| M8-2 - Body ground | Always | 10 kΩ or higher |
| M8-1 - Body ground | Always | 10 kΩ or higher |
| J133-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| J133-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| N10-2 - Body ground | Always | 10 kΩ or higher |
| N10-1 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER(for Regular Cab)>REMOVAL).
Inspect the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER(for Regular Cab)>INSPECTION).
OK
NG
Replace the front No. 2 speaker assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER(for Regular Cab)>REMOVAL).
Check that the malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
Perform the above inspection on both LH and RH sides.
Malfunction disappears.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Column Shift Type) | B |
| NG (for Floor Shift Type) | C |
A
B
C
*1: for RH Side
*2: for LH Side
*3: for 9 Speakers
Disconnect the J133 and J134 navigation receiver assembly connector.
Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.
Disconnect the J147*1 and/or J149*2 front No. 2 speaker assembly connector.
Disconnect the J150 front No. 4 speaker assembly connector.
Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.
Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector.*3
Disconnect the J144 and J145 stereo component amplifier assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M8-1 - J144-1 (R+) | Always | Below 1 Ω |
| M8-2 - J144-5 (R-) | Always | Below 1 Ω |
| N10-1 - J144-2 (L+) | Always | Below 1 Ω |
| N10-2 - J144-6 (L-) | Always | Below 1 Ω |
| O1-1 - J145-4 (WFR+) | Always | Below 1 Ω |
| O1-2 - J145-11 (WFR-) | Always | Below 1 Ω |
| O7-1 - J145-5 (WFL+) | Always | Below 1 Ω |
| O7-2 - J145-12 (WFL-) | Always | Below 1 Ω |
| O2-3 - J145-9 (RR+)*3 | Always | Below 1 Ω |
| O2-2 - J145-10 (RR-)*3 | Always | Below 1 Ω |
| J145-9 (RR+) - J134-1 (RR+) | Always | Below 1 Ω |
| J145-10 (RR-) - J134-3 (RR-) | Always | Below 1 Ω |
| O8-3 - J145-3 (RL+)*3 | Always | Below 1 Ω |
| O8-2 - J145-8 (RL-)*3 | Always | Below 1 Ω |
| J145-3 (RL+) - J134-2 (RL+) | Always | Below 1 Ω |
| J145-8 (RL-) - J134-6 (RL-) | Always | Below 1 Ω |
| J145-2 (FR+) - J133-1 (FR+) | Always | Below 1 Ω |
| J145-7 (FR-) - J133-5 (FR-) | Always | Below 1 Ω |
| J145-1 (FL+) - J133-2 (FL+) | Always | Below 1 Ω |
| J145-6 (FL-) - J133-6 (FL-) | Always | Below 1 Ω |
| J145-2 (FR+) - J147-3 (TWR+) | Always | Below 1 Ω |
| J145-7 (FR-) - J147-2 (TWR-) | Always | Below 1 Ω |
| J145-1 (FL+) - J149-3 (TWL+) | Always | Below 1 Ω |
| J145-6 (FL-) - J149-2 (TWL-) | Always | Below 1 Ω |
| J147-1 (+) - J150-1 (+) | Always | Below 1 Ω |
| J147-4 (-) - J150-4 (RI1-) | Always | Below 1 Ω |
| J150-2 (-) - J149-4 (-) | Always | Below 1 Ω |
| J150-3 (RI1+) - J149-1 (+) | Always | Below 1 Ω |
| J144-1 (R+) - Body ground | Always | 10 kΩ or higher |
| J144-5 (R-) - Body ground | Always | 10 kΩ or higher |
| J144-2 (L+) - Body ground | Always | 10 kΩ or higher |
| J144-6 (L-) - Body ground | Always | 10 kΩ or higher |
| J145-4 (WFR+) - Body ground | Always | 10 kΩ or higher |
| J145-11 (WFR-) - Body ground | Always | 10 kΩ or higher |
| J145-5 (WFL+) - Body ground | Always | 10 kΩ or higher |
| J145-12 (WFL-) - Body ground | Always | 10 kΩ or higher |
| J145-9 (RR+) - Body ground | Always | 10 kΩ or higher |
| J145-10 (RR-) - Body ground | Always | 10 kΩ or higher |
| J145-3 (RL+) - Body ground | Always | 10 kΩ or higher |
| J145-8 (RL-) - Body ground | Always | 10 kΩ or higher |
| J145-2 (FR+) - Body ground | Always | 10 kΩ or higher |
| J145-7 (FR-) - Body ground | Always | 10 kΩ or higher |
| J145-1 (FL+) - Body ground | Always | 10 kΩ or higher |
| J145-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| J147-1 (+) - Body ground | Always | 10 kΩ or higher |
| J147-4 (-) - Body ground | Always | 10 kΩ or higher |
| J147-3 (TWR+) - Body ground | Always | 10 kΩ or higher |
| J147-2 (TWR-) - Body ground | Always | 10 kΩ or higher |
| J150-2 (-) - Body ground | Always | 10 kΩ or higher |
| J150-3 (RI1+) - Body ground | Always | 10 kΩ or higher |
| J149-3 (TWL+) - Body ground | Always | 10 kΩ or higher |
| J149-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the front No. 1 speaker assembly.
for Double Cab: See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER(for Double Cab)>REMOVAL
for CrewMax: See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER(for CrewMax)>REMOVAL
Inspect the front No. 1 speaker assembly.
for Double Cab: See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER(for Double Cab)>INSPECTION
for CrewMax: See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER(for CrewMax)>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Double Cab) | B |
| NG (for CrewMax) | C |
A
B
C
Replace the front No. 2 speaker assembly with a known good one.
for Double Cab: See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER(for Double Cab)>REMOVAL
for CrewMax: See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER(for CrewMax)>REMOVAL
Check that the malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
Perform the above inspection on both LH and RH sides.
Malfunction disappears.
OK
NG
Replace the front No. 4 speaker assembly with a known good one.
for Double Cab: See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER(for Double Cab)>REMOVAL
for CrewMax: See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER(for CrewMax)>REMOVAL
Check that the malfunction disappears.
Malfunction disappears.
OK
NG
Remove the rear No. 1 speaker assembly with a known good one.
for Double Cab: See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>REMOVAL
for CrewMax: See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for CrewMax)>REMOVAL
Inspect the rear No. 1 speaker assembly with a known good one.
for Double Cab: See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for Double Cab)>INSPECTION
for CrewMax: See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for CrewMax)>INSPECTION
| Result | Proceed to |
|---|---|
| OK (for CrewMax) | A |
| OK (for Double Cab) | B |
| NG (for Double Cab) | C |
| NG (for CrewMax) | D |
A
B
C
D
Replace the rear No. 2 speaker assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for CrewMax)>REMOVAL).
Check that the malfunction disappears.
Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
Perform the above inspection on both LH and RH sides.
Malfunction disappears.
OK
NG
Replace the stereo component amplifier assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).
Check that the malfunction disappears.
Malfunction disappears.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Double Cab) | B |
| NG (for CrewMax) | C |
A
B
C
*1: for RH Side
*2: for LH Side
Disconnect the M8*1 and/or N10*2 front No. 1 speaker assembly connector.
Disconnect the J146*1 and/or J148*2 front No. 2 speaker assembly connector.
Disconnect the M1*1 and/or N1*2 front No. 3 speaker assembly connector.
Disconnect the J150 front No. 4 speaker assembly connector.
Disconnect the O1*1 and/or O7*2 rear No. 1 speaker assembly connector.
Disconnect the O2*1 and/or O8*2 rear No. 2 speaker assembly connector.
Disconnect the P14 No. 1 box speaker assembly connector.
Disconnect the J142 and J143 stereo component amplifier assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J142-2 (FR+) - J146-3 (TWR+) | Always | Below 1 Ω |
| J142-6 (FR-) - J146-4 (TWR-) | Always | Below 1 Ω |
| J146-1 (+) - M1-3 | Always | Below 1 Ω |
| J146-2 (-) - M1-2 | Always | Below 1 Ω |
| J143-9 (WFR+) - M8-1 | Always | Below 1 Ω |
| J143-3 (WFR-) - M8-2 | Always | Below 1 Ω |
| J142-10 (RR+) - O2-3 (+TW) | Always | Below 1 Ω |
| J142-4 (RR-) - O2-2 (-TW) | Always | Below 1 Ω |
| O2-4 (+) - O1-2 | Always | Below 1 Ω |
| O2-1 (-) - O1-1 | Always | Below 1 Ω |
| J142-5 (WF1+) - P14-1 | Always | Below 1 Ω |
| J142-12 (WF1-) - P14-2 | Always | Below 1 Ω |
| J142-3 (RL+) - O8-3 (+TW) | Always | Below 1 Ω |
| J142-9 (RL-) - O8-2 (-TW) | Always | Below 1 Ω |
| O8-4 (+) - O7-1 | Always | Below 1 Ω |
| O8-1 (-) - O7-2 | Always | Below 1 Ω |
| J143-2 (WFL+) - N10-1 | Always | Below 1 Ω |
| J143-1 (WFL-) - N10-2 | Always | Below 1 Ω |
| J142-8 (FL+) - J148-3 (TWL+) | Always | Below 1 Ω |
| J142-7 (FL-) - J148-4 (TWL-) | Always | Below 1 Ω |
| J148-1 (+) - N1-3 | Always | Below 1 Ω |
| J148-2 (-) - N1-2 | Always | Below 1 Ω |
| J143-4 (CTR+) - J150-1 | Always | Below 1 Ω |
| J143-10 (CTR-) - J150-2 | Always | Below 1 Ω |
| J142-2 (FR+) - Body ground | Always | 10 kΩ or higher |
| J142-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| J146-1 (+) - Body ground | Always | 10 kΩ or higher |
| J146-2 (-) - Body ground | Always | 10 kΩ or higher |
| J143-9 (WFR+) - Body ground | Always | 10 kΩ or higher |
| J143-3 (WFR-) - Body ground | Always | 10 kΩ or higher |
| J142-10 (RR+) - Body ground | Always | 10 kΩ or higher |
| J142-4 (RR-) - Body ground | Always | 10 kΩ or higher |
| O2-4 (+) - Body ground | Always | 10 kΩ or higher |
| O2-1 (-) - Body ground | Always | 10 kΩ or higher |
| J142-5 (WF1+) - Body ground | Always | 10 kΩ or higher |
| J142-12 (WF1-) - Body ground | Always | 10 kΩ or higher |
| J142-3 (RL+) - Body ground | Always | 10 kΩ or higher |
| J142-9 (RL-) - Body ground | Always | 10 kΩ or higher |
| O8-4 (+) - Body ground | Always | 10 kΩ or higher |
| O8-1 (-) - Body ground | Always | 10 kΩ or higher |
| J143-2 (WFL+) - Body ground | Always | 10 kΩ or higher |
| J143-1 (WFL-) - Body ground | Always | 10 kΩ or higher |
| J142-8 (FL+) - Body ground | Always | 10 kΩ or higher |
| J142-7 (FL-) - Body ground | Always | 10 kΩ or higher |
| J148-1 (+) - Body ground | Always | 10 kΩ or higher |
| J148-2 (-) - Body ground | Always | 10 kΩ or higher |
| J143-4 (CTR+) - Body ground | Always | 10 kΩ or higher |
| J143-10 (CTR-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER(for CrewMax)>REMOVAL).
Inspect the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER(for CrewMax)>INSPECTION).
OK
NG
Replace the front No. 2 speaker assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER(for CrewMax)>REMOVAL).
Check that the malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
Perform the above inspection on both LH and RH sides.
Malfunction disappears.
OK
NG
Replace the front No. 4 speaker assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER(for CrewMax)>REMOVAL).
Check that the malfunction disappears.
Malfunction disappears.
OK
NG
Replace the front No. 3 speaker assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER(for CrewMax)>REMOVAL).
Check that the malfunction disappears.
Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
Perform the above inspection on both LH and RH sides.
Malfunction disappears.
OK
NG
Remove the No. 1 box speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FLOOR SPEAKER(for CrewMax)>REMOVAL).
Inspect the No. 1 box speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FLOOR SPEAKER(for CrewMax)>INSPECTION).
OK
NG
Remove the rear No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for CrewMax)>REMOVAL).
Inspect the rear speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for CrewMax)>INSPECTION).
OK
NG
Replace the rear No. 2 speaker assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER(for CrewMax)>REMOVAL).
Check that the malfunction disappears.
Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
Connect all the connectors to the rear No. 2 speaker assemblies that were disconnected.
Perform the above inspection on both LH and RH sides.
Malfunction disappears.
OK
NG
Replace the stereo component amplifier assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL).
Check that the malfunction disappears.
Malfunction disappears.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Column Shift Type) | B |
| NG (for Floor Shift Type) | C |
A
B
C