Home › Vehicle Interior › WINDOW / GLASS › BACK WINDOW GLASS(for CrewMax)
RM27M0U _58 Vehicle Interior _049161 WINDOW / GLASS _0234471 BACK WINDOW GLASS(for CrewMax) A

WINDOW / GLASS  BACK WINDOW GLASS(for CrewMax)  REMOVAL  


PROCEDURE

Hide 28800 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


Hide 75554A 2.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING LH

Hide 75553A 3.REMOVE REAR ROOF DRIP SIDE FINISH MOULDING RH

HINT:

Use the same procedures described for the LH side.


Hide 67918B 6.REMOVE REAR DOOR SCUFF PLATE LH

Hide 67917B 7.REMOVE REAR DOOR SCUFF PLATE RH

Hide 62332A 8.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.

Partially remove the rear door opening trim weatherstrip LH so that the lower quarter trim panel LH and front quarter trim panel LH can be removed (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for CrewMax)>REMOVAL).


Hide 62331A 9.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedures described for the LH side.


Hide 73024 10.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

Hide 73023 11.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 62540 13.REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY LH

Hide 62530 14.REMOVE LOWER QUARTER TRIM PANEL ASSEMBLY RH

Hide 62520P 15.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH

Hide 62510P 16.REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

Hide 81240 18.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 63310 19.TEMPORARILY REMOVE ROOF HEADLINING ASSEMBLY

a.

It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining (see page Vehicle Interior>INTERIOR>ROOF HEADLINING(for CrewMax)>REMOVAL) so that the back window glass can be removed in a later step.


Hide 67152A 20.REMOVE BACK DOOR SERVICE HOLE COVER

a.

Remove the back window regulator connector labeled A.


b.

Remove the 12 bolts and nut.


c.

Lift the cover upwards to detach the claw labeled B. Then slide the cover to the left to disengage the retainer labeled C and remove the cover.

NOTICE:

When the cover is removed, the cover may fall and become deformed.


U151961E02
2.25,1.115 2.458,1.313 0.208,0.198 10 false A 0.875,2.802 1.042,3 0.167,0.198 10 true B 6.177,0.698 6.385,0.896 0.208,0.198 10 false C


Hide 68290B 21.REMOVE OUTER BACK DOOR GLASS WEATHERSTRIP ASSEMBLY

a.

Using a screwdriver, detach the 9 claws and remove the weatherstrip.

HINT:

Tape the screwdriver tip before use.


B168899


Hide 68291F 22.REMOVE INNER BACK DOOR GLASS WEATHERSTRIP

B168900

a.

Using a screwdriver, remove the weatherstrip.

HINT:

Tape the screwdriver tip before use.



Hide 68275A 23.REMOVE BACK DOOR GLASS RUN

B168901

a.

Remove the glass run.


Hide 64811 24.REMOVE BACK WINDOW GLASS

a.

Connect the cable to the negative (-) battery terminal.


b.

Connect the back window regulator connector labeled A.


c.

Move the back window glass until the bolts appear in the service holes.


d.

Disconnect the back window regulator connector labeled A.


e.

Disconnect the cable from the negative battery (-) terminal.


f.

Disconnect the 2 defogger connectors labeled B.


g.

Remove the 4 bolts.

NOTICE:

Be careful when removing the bolts as the glass may fall and become damaged.



h.

Remove the back window glass.

HINT:

Remove the glass upward.


NOTICE:

Be careful not to damage the glass.


U151963E02
1.917,4.656 2.125,4.854 0.208,0.198 10 true A 5.719,0.385 5.948,0.583 0.229,0.198 10 true B 6.115,0.375 6.323,0.573 0.208,0.198 10 true B


Hide 69807A 25.REMOVE BACK DOOR POWER WINDOW REGULATOR SUB-ASSEMBLY

a.

Remove the 7 bolts and back window regulator.

HINT:

Remove the regulator through the service hole.


NOTICE:

Be careful when removing the bolts as the regulator sub-assembly may fall and become damaged.


B168903


Hide 85710J 26.REMOVE BACK DOOR POWER WINDOW REGULATOR MOTOR

B171645

NOTICE:

Perform these procedures only when replacing the regulator or motor.


a.

Remove the 2 nuts and motor.

NOTICE:

Be careful when removing the nuts as the motor may fall and become damaged.



b.

Remove the 2 screws and cover.


c.
B171648

Remove the drum and wire guide from the motor.

NOTICE:

Do not pry the drum with a screwdriver or equivalent.



Hide 75573F 27.REMOVE BACK WINDOW OUTSIDE MOULDING

a.

Put a 4 mm (0.157 in.) drill bit into a drill.


b.

Wind tape around the drill bit 5 mm (0.196 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill against the rivets, drill off the flanges of the rivets, and remove the 16 rivets.

B168906E01
6.172,0.415 6.626,0.630 0.455,0.215 10 5 mm

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, because this may cause damage to the installation holes of the rivets or the drill bit.

·

Be careful of the drilled rivets as they may become hot.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.


e.
B171651

Remove the 3 clips and back window outside moulding.


Hide 61576A 28.REMOVE UPPER CAB REAR PILLAR PLATE LH

B168905

a.

Remove the 4 bolts and upper plate.


Hide 61575C 29.REMOVE UPPER CAB REAR PILLAR PLATE RH

HINT:

Use the same procedures described for the LH side.