Home › Power Source / Network › MULTIPLEX COMMUNICATION › LIN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049167 MULTIPLEX COMMUNICATION _0234509 LIN COMMUNICATION SYSTEM C

MULTIPLEX COMMUNICATION  LIN COMMUNICATION SYSTEM  B2325  LIN Communication Bus Malfunction  


DESCRIPTION

The main body ECU (driver side junction block) intermittently monitors the LIN communication bus between the components related to the window and sliding roof. DTC B2325 is stored when a malfunction in the LIN communication bus between the components related to the window and sliding roof is detected consecutively 3 times.

DTC Code DTC Detection Condition Trouble Area
B2325 The main body ECU (driver side junction block) detects a malfunction in the LIN communication bus between components related to the window and sliding roof consecutively 3 times.
·

Power window regulator master switch assembly*1

·

Front power window regulator motor assembly LH*1

·

Front power window regulator motor assembly RH*1

·

Sliding roof drive gear sub-assembly (Sliding Roof ECU)*2

·

Main body ECU (driver side junction block)

·

Harness or connector



HINT:
·

*1: for Power Window Control System (w/ Jam Protection Function)

·

*2: w/ Sliding Roof System



WIRING DIAGRAM

U152442E01
0.073,0.938 1.094,1.688 1.021,0.75 10 false Main Body ECU (Driver Side Junction Block) 0.073,0.74 0.333,0.927 0.26,0.188 10 false J2 1.573,1.063 1.896,1.25 0.323,0.188 10 false LIN2 3.615,1.052 3.938,1.24 0.323,0.188 10 false LIN2 4.781,1.052 5.104,1.24 0.323,0.188 10 false LIN 3.26,2.813 3.583,3 0.323,0.188 10 false LIN 3.26,4.26 3.583,4.448 0.323,0.188 10 false LIN 3.271,1.052 3.594,1.24 0.323,0.188 10 false LIN1 1.958,0.885 2.219,1.042 0.26,0.156 10 false 10 3.073,0.885 3.208,1.042 0.135,0.156 10 false 6 3.083,2.646 3.219,2.802 0.135,0.156 10 false 9 3.083,4.104 3.219,4.26 0.135,0.156 10 false 3 4.01,0.885 4.146,1.042 0.135,0.156 10 false 7 4.583,0.885 4.719,1.042 0.135,0.156 10 false 9 2.76,1.469 3.021,1.656 0.26,0.188 10 false N2 4.042,2.594 4.417,2.781 0.375,0.188 10 false M11 5.604,0.74 5.938,0.927 0.333,0.188 10 false N12 2.76,1.625 4.438,1.99 1.677,0.365 10 false Power Window Regulator Master Switch Assembly*1 5.604,0.896 6.948,1.531 1.344,0.635 10 false Front Power Window Regulator Motor Assembly LH*1 0.646,5.688 2.323,5.875 1.677,0.188 10 false : LIN Communication Line 4.042,2.76 6.021,3.125 1.979,0.365 10 false Front Power Window Regulator Motor Assembly RH*1 4.031,4.323 6.458,4.677 2.427,0.354 10 false Sliding Roof Drive Gear Sub-assembly (Sliding Roof ECU)*2 4.031,4.125 4.302,4.313 0.271,0.188 10 false W3 0.604,6.031 5.125,6.219 4.521,0.188 10 false *1: for Power Window Control System (w/ Jam Protection Function) 0.604,6.333 2.323,6.521 1.719,0.188 10 false *2: w/ Sliding Roof System

CAUTION / NOTICE / HINT

NOTICE:

When using the Techstream with the ignition switch OFF to troubleshoot:

Connect the Techstream to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.


HINT:

When DTC B2325 and a LIN communication stop DTC are output simultaneously, first perform the troubleshooting for the LIN communication stop DTC. Then perform the troubleshooting for DTC B2325.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 output reoccurs A
DTC B2325 output does not reoccur B



A

3.SYSTEM CHECK

B

3.SYSTEM CHECK
a.

Check the vehicle specifications.

Result
Result Proceed to
for Power Window Control System (w/ Jam Protection Function) and w/ Sliding Roof System, or for Power Window Control System (w/ Jam Protection Function) and w/o Sliding Roof System A
for Power Window Control System (w/o Jam Protection Function) and w/ Sliding Roof System B



A

4.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REGULATOR MOTOR LH)

B

15.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SLIDING ROOF DRIVE GEAR)
4.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - REGULATOR MOTOR LH)
a.

Disconnect the N2 power window regulator master switch assembly connector.

E344935E01
0.927,1.583 1.281,1.781 0.354,0.198 4.521,1.604 4.896,1.813 0.375,0.208 2.188,1.635 2.604,1.219 false 5.281,1.979 5.542,2.26 false 0.646,0.25 2.927,0.781 2.281,0.531 10 false Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 4.177,0.25 6.458,0.781 2.281,0.531 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly LH) 1.01,1.594 1.24,1.75 0.229,0.156 10 false N2 4.583,1.625 4.885,1.781 0.302,0.156 10 false N12 2.635,1.042 2.979,1.198 0.344,0.156 10 false LIN2 5.594,2.25 5.938,2.406 0.344,0.156 10 false LIN


b.

Disconnect the N12 front power window regulator motor assembly LH connector.


c.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N2-7 (LIN2) - N12-9 (LIN) Always Below 1 Ω
N2-7 (LIN2) or N12-9 (LIN) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
N2-7 (LIN2) - Body ground Always Below 1 V




OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - EACH ECU)
U152443E02
2.063,1.396 2.438,1.271 false 5.594,1.5 5.792,1.063 false 5.802,3.125 5.979,2.948 false 1.823,3.813 2.021,4.042 false 1.094,1.302 1.292,1.479 0.198,0.177 10 false J2 4.51,1.49 4.719,1.667 0.208,0.177 10 false N2 0.448,0.073 2.813,0.469 2.365,0.396 10 false Front view of wire harness connector: (to Main Body ECU) 4.094,0.073 6.458,0.615 2.365,0.542 10 false Front view of wire harness connector: (to Power Window Regulator Master Switch Assembly) 2.49,1.167 2.802,1.344 0.313,0.177 10 false LIN2 5.823,0.906 6.135,1.083 0.313,0.177 10 false LIN1 4.708,3.208 4.979,3.385 0.271,0.177 10 false W3 4.094,1.948 6.521,2.521 2.427,0.573 10 false Front view of wire harness connector: (to Sliding Roof Drive Gear Sub-assembly)* 6.031,2.802 6.427,2.979 0.396,0.177 10 false LIN 1.104,3.5 1.427,3.677 0.323,0.177 10 false M11 0.51,1.948 2.938,2.469 2.427,0.521 10 false Front view of wire harness connector: (to Front Power Window Regulator Motor Assembly RH) 2.063,3.979 2.292,4.156 0.229,0.177 10 false LIN 0.135,4.427 2.219,4.604 2.083,0.177 10 false *: w/ Sliding Roof System

a.

Disconnect the J2 main body ECU (driver side junction block) connector.


b.

Disconnect the N2 power window regulator master switch assembly connector.


c.

Disconnect the M11 front power window regulator motor assembly RH connector.


d.

w/ Sliding Roof System:

Disconnect the W3 sliding roof drive gear sub-assembly connector.


e.

Measure the resistance and voltage according to the value(s) in the tables below.

Standard Resistance:
Tester Connection Condition Specified Condition
J2-10 (LIN2) - N2-6 (LIN1) Always Below 1 Ω
J2-10 (LIN2) - M11-9 (LIN)
J2-10 (LIN2) - W3-3 (LIN)*
J2-10 (LIN2) - Body ground Always 10 kΩ or higher


HINT:

*: w/ Sliding Roof System


Standard Voltage:
Tester Connection Condition Specified Condition
J2-10 (LIN2) - Body ground Always Below 1 V




OK

6.SYSTEM CHECK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.SYSTEM CHECK
a.

Check the vehicle specifications.

Result
Result Proceed to
w/ Sliding Roof System A
w/o Sliding Roof System B



A

7.CLEAR DTC

B

9.CLEAR DTC
7.CLEAR DTC
a.

Reconnect the J2 main body ECU (driver side junction block) connector.


b.

Reconnect the N2 power window regulator master switch assembly connector.


c.

Reconnect the M11 front power window regulator motor assembly RH connector.


d.

Disconnect the W3 sliding roof drive gear sub-assembly connector.




NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 output reoccurs A
DTC B2325 output does not reoccur B



A

9.CLEAR DTC

B

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

9.CLEAR DTC
a.

w/ Sliding Roof System:

Reconnect the W3 sliding roof drive gear sub-assembly connector.


b.

Disconnect the N12 power window regulator motor assembly LH connector.




NEXT

10.CHECK FOR DTC
10.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 output reoccurs A
DTC B2325 output does not reoccur B



A

11.CLEAR DTC

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

11.CLEAR DTC
a.

Reconnect the N12 power window regulator motor assembly LH connector.


b.

Disconnect the N2 power window regulator master switch assembly connector.




NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 output reoccurs A
DTC B2325 output does not reoccur B



A

13.CLEAR DTC

B

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

13.CLEAR DTC
a.

Reconnect the N2 power window regulator master switch assembly connector.


b.

Disconnect the M11 power window regulator motor assembly RH connector.




NEXT

14.CHECK FOR DTC
14.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 output reoccurs A
DTC B2325 output does not reoccur B



A

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

15.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SLIDING ROOF DRIVE GEAR)
U152043E03
4.521,3.25 4.302,2.927 false 2.417,3.469 1.885,3.781 false 1.583,3.719 1.917,3.896 0.333,0.177 10 false LIN2 4.073,2.802 4.354,2.979 0.281,0.177 10 false LIN 0.938,0.188 3.323,0.552 2.385,0.365 10 false Rear view of wire harness connector: (to Main Body ECU) 4.219,0.323 6.75,0.698 2.531,0.375 10 false Rear view of wire harness connector: (to Sliding Roof Drive Gear Sub-assembly) 1.833,3.208 2.104,3.375 0.271,0.167 10 false J2 3.875,3.24 4.146,3.406 0.271,0.167 10 false W3

a.

Disconnect the J2 main body ECU (driver side junction block) connector.


b.

Disconnect the W3 sliding roof drive gear sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J2-10 (LIN2) - W3-3 (LIN) Always Below 1 Ω
J2-10 (LIN2) or W3-3 (LIN) - Body ground Always 10 kΩ or higher




OK

16.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - BATTERY AND BODY GROUND)
a.
U151887E02
1.76,1.573 1.448,1.854 false 2.125,1.573 2.323,1.875 false 0.083,0.073 2.385,0.625 2.302,0.552 10 false Front view of wire harness connector: (to Sliding Roof Drive Gear Sub-assembly) 0.74,1.292 0.969,1.458 0.229,0.167 10 false W3 2.354,1.854 2.5,2.021 0.146,0.167 10 false B 1.333,1.844 1.479,2.01 0.146,0.167 10 false E

Disconnect the W3 sliding roof drive gear sub-assembly connector.


b.

Measure the resistance and voltage according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W3-8 (E) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
W3-10 (B) - Body ground Always 11 to 14 V




OK

17.REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
a.

Temporarily replace the sliding roof drive gear sub-assembly with a new or normally functioning one (See page Vehicle Interior>SLIDING ROOF>SLIDING ROOF HOUSING(for CrewMax)>DISASSEMBLY).




NEXT

18.CHECK DTC
18.CHECK DTC
a.

Check for DTCs (See page Power Source / Network>MULTIPLEX COMMUNICATION>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B2325 output does not reoccur A
DTC B2325 output reoccurs B



A

END (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY [SLIDING ROOF ECU] IS DEFECTIVE)

B

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)