Home › Power Source / Network › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM
RM27M0U _57 Power Source / Network _049168 CAN COMMUNICATION _0234510 CAN COMMUNICATION SYSTEM C

CAN COMMUNICATION  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module  


DESCRIPTION

·

The main body ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.

·

When the main body ECU receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 Lost communication with gateway module
·

MS bus circuit

·

Front power seat control ECU and switch LH CAN branch wire or connector

·

Multiplex tilt and telescopic ECU CAN branch wire or connector

·

Outer mirror control ECU assembly CAN branch wire or connector

·

Combination meter assembly CAN main wire or connector

·

Main body ECU (driver side junction block assembly) CAN main wire or connector

·

Front power seat control ECU and switch LH

·

Multiplex tilt and telescopic ECU

·

Outer mirror control ECU assembly

·

Combination meter assembly

·

Main body ECU (driver side junction block assembly)

·

No. 3 junction connector



For vehicle with a seat memory.


WIRING DIAGRAM

C288314E02
5.6,1.202 6.034,1.340 0.434,0.139 10 MSCL 5.6,0.648 6.034,0.787 0.434,0.139 10 MSCH 5.308,1.03 5.496,1.169 0.187,0.139 10 19 5.308,0.648 5.496,0.787 0.187,0.139 10 18 2.909,4.897 3.274,5.046 0.365,0.149 10 J76 2.909,5.051 4.507,5.200 1.598,0.149 10 No. 3 Junction Connector 0.604,3.165 0.895,3.314 0.291,0.149 10 N8 0.604,3.299 2.350,3.604 1.746,0.305 10 Outer Mirror Control ECU Assembly 3.984,1.03 4.172,1.169 0.187,0.139 10 12 3.984,0.648 4.093,0.787 0.108,0.139 10 1 3.098,1.03 3.285,1.169 0.187,0.139 10 13 3.178,0.648 3.286,0.787 0.108,0.139 10 2 1.919,1.03 2.106,1.169 0.187,0.139 10 14 1.919,0.648 2.027,0.787 0.108,0.139 10 5 1.386,1.116 1.778,1.254 0.392,0.139 10 CANL 1.363,0.73 1.778,0.869 0.415,0.139 10 CANH 3.984,2.744 4.172,2.883 0.187,0.139 10 14 3.984,2.362 4.093,2.501 0.108,0.139 10 3 3.984,4.471 4.172,4.609 0.187,0.139 10 15 3.984,4.094 4.093,4.232 0.108,0.139 10 4 3.098,2.744 3.285,2.883 0.187,0.139 10 16 3.178,2.362 3.286,2.501 0.108,0.139 10 5 5.391,2.744 5.496,2.883 0.106,0.139 10 7 5.388,2.362 5.496,2.501 0.108,0.139 10 8 5.6,2.83 6.029,2.968 0.429,0.139 10 CANN 5.6,2.444 6.034,2.583 0.434,0.139 10 CANP 5.6,4.653 6.029,4.791 0.429,0.139 10 CANN 5.6,4.094 6.034,4.232 0.434,0.139 10 CANP 1.919,2.744 2.106,2.883 0.187,0.139 10 21 1.919,2.362 2.027,2.501 0.108,0.139 10 1 1.349,2.83 1.778,2.968 0.429,0.139 10 CGND 1.461,2.444 1.779,2.583 0.318,0.139 10 CAN 5.324,4.094 5.496,4.234 0.172,0.141 10 16 5.315,4.471 5.496,4.609 0.180,0.138 10 15 5.204,4.881 5.496,5.030 0.291,0.149 10 J2 5.204,5.015 6.958,5.320 1.754,0.305 10 Main Body ECU (Cowl Side Junction Block LH) 5.4,1.45 5.692,1.599 0.291,0.149 10 J28 5.4,1.583 6.688,1.889 1.288,0.305 10 Combination Meter Assembly 5.144,3.183 5.435,3.332 0.291,0.149 10 Z10 5.144,3.316 7.064,3.621 1.920,0.305 10 Front Power Seat Control ECU and Switch LH 0.604,1.45 0.895,1.599 0.291,0.149 10 J47 0.604,1.583 2.350,1.889 1.746,0.305 10 Multiplex Tilt and Telescopic ECU

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any other switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.PRECAUTION
NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



NEXT

2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




NEXT

3.CHECK CAN BUS WIRE (CHECK MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
3.CHECK CAN BUS WIRE (CHECK MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
a.
U152534E01
0.069,0.049 0.288,0.246 0.218,0.198 10 *a 1.604,0.281 1.845,0.423 0.242,0.142 10 J28 2.325,1.152 2.509,1.522 2.509,1.522 2.661,1.522 false 0.736,0.497 0.843,0.497 0.843,0.497 1.073,0.992 false 2.586,1.009 2.774,0.841 2.774,0.841 2.897,0.841 false 0.982,0.992 0.78,0.765 0.78,0.765 0.688,0.765 false 0.187,0.692 0.591,0.834 0.404,0.142 10 MSCL 0.207,0.403 0.633,0.545 0.427,0.142 10 MSCH 2.675,1.434 2.885,1.576 0.210,0.142 10 ES 2.934,0.758 3.058,0.900 0.125,0.142 10 B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance of Malfunction
J28-18 (MSCH) - J28-19 (MSCL) Ignition switch off 54 to 69 Ω Below 53 Ω: Short in line
J28-18 (MSCH) - J28-19 (MSCL) Ignition switch off 54 to 69 Ω 70 Ω or higher: Open in CAN main bus line
J28-18 (MSCH) - J28-1 (B) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
J28-19 (MSCL) - J28-1 (B) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
J28-18 (MSCH) - J28-24 (ES) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short
J28-19 (MSCL) - J28-24 (ES) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

Result
Result Proceed to
NG
·

Open in CAN main wire


A
NG
·

Short in line

·

+B short

·

Ground short


B
OK C



A

4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

B

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FRONT POWER SEAT CONTROL ECU AND SWITCH LH)

C

25.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U152535E01
1.946,1.417 2.39,1.866 2.39,1.866 2.572,1.866 false 1.946,1.199 2.39,0.75 2.39,0.75 2.572,0.75 false 0.441,1.236 0.684,1.377 0.243,0.140 10 J76 2.59,0.674 3.051,0.814 0.460,0.140 10 CANH 2.59,1.791 3.051,1.931 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Disconnect the J76 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J76-4 (CANH) - J76-15 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

8.CONNECT CONNECTOR
5.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U152536E01
0.441,1.236 0.684,1.377 0.243,0.140 10 J76 2.266,1.417 2.39,1.663 2.39,1.663 2.572,1.663 false 2.266,1.199 2.453,0.959 2.453,0.959 2.635,0.959 false 2.653,0.883 3.114,1.023 0.460,0.140 10 CANH 2.59,1.588 3.051,1.728 0.460,0.140 10 CANL 0.061,0.049 0.415,0.190 0.354,0.140 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J76-1 (CANH) - J76-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

6.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the J76 No. 3 junction connector.



NEXT

7.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)
a.
U152502E01
1.018,1.1 0.881,0.886 0.881,0.886 0.763,0.886 false 1.113,1.1 1.01,0.636 1.01,0.636 0.893,0.636 false 0.364,0.55 0.795,0.692 0.431,0.142 10 MSCH 0.267,0.811 0.677,0.953 0.410,0.142 10 MSCL 0.08,0.057 0.500,0.199 0.420,0.142 10 *a 1.571,0.208 1.815,0.350 0.244,0.142 10 J28

Disconnect the J28 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J28-18 (MSCH) - J28-19 (MSCL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the J76 No. 3 junction connector.



NEXT

9.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)
9.CHECK FOR OPEN IN CAN BUS WIRE (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)
a.
U152507E01
2.05,1.533 2.305,1.928 2.305,1.928 2.443,1.928 false 1.934,1.533 1.679,1.928 1.679,1.928 1.541,1.928 false 2.469,1.853 2.891,1.989 0.422,0.137 10 CANP 1.021,1.853 1.443,1.989 0.422,0.137 10 CANN 0.7,1.161 0.876,1.298 0.176,0.137 10 J2 0.067,0.048 0.267,0.185 0.199,0.137 10 *a

Disconnect the J2 main body ECU (driver side junction block assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J2-16 (CANP) - J2-15 (CANN) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Driver Side Junction Block Assembly])



OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 3 JUNCTION CONNECTOR)

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - FRONT POWER SEAT CONTROL ECU AND SWITCH LH)
a.
U152579E01
0.418,2.696 0.662,2.835 0.244,0.140 10 J17 0.552,1.091 0.795,1.231 0.243,0.140 10 J76 1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.018,1.291 2.25,1.651 2.25,1.651 2.347,1.651 false 2.414,0.792 2.299,0.792 2.299,0.792 2.018,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.436,0.715 2.855,0.857 0.420,0.142 10 CANH 2.373,1.565 2.797,1.707 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Disconnect the J76 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J76-3 (CANH) - J76-14 (CANL) Ignition switch off 200 Ω or higher
J76-3 (CANH) - J17-4 (CG) Ignition switch off 200 Ω or higher
J76-14 (CANL) - J17-4 (CG) Ignition switch off 200 Ω or higher
J76-3 (CANH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
J76-14 (CANL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

NG

15.CONNECT CONNECTOR
11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)
a.
U152575E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.112,1.291 2.271,1.569 2.271,1.569 2.369,1.569 false 2.482,0.882 2.368,0.882 2.368,0.882 2.112,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.504,0.805 2.924,0.947 0.420,0.142 10 CANH 2.395,1.483 2.819,1.625 0.424,0.142 10 CANL 2.54,3.123 2.964,3.265 0.424,0.142 10 BAT 1.062,2.087 1.291,2.229 0.229,0.142 10 CG 0.418,2.696 0.662,2.835 0.244,0.140 10 J17 0.552,1.091 0.795,1.231 0.243,0.140 10 J76

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J76-2 (CANH) - J76-13 (CANL) Ignition switch off 200 Ω or higher
J76-2 (CANH) - J17-4 (CG) Ignition switch off 200 Ω or higher
J76-13 (CANL) - J17-4 (CG) Ignition switch off 200 Ω or higher
J76-2 (CANH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
J76-13 (CANL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY)

NG

17.CONNECT CONNECTOR
12.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY)
a.
U152576E01
0.418,2.696 0.662,2.835 0.244,0.140 10 J17 0.552,1.091 0.795,1.231 0.243,0.140 10 J76 1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.817,1.291 2.048,1.681 2.048,1.681 2.145,1.681 false 2.392,0.643 2.278,0.643 2.278,0.643 1.817,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.414,0.566 2.834,0.708 0.420,0.142 10 CANH 2.171,1.595 2.595,1.737 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J76-5 (CANH) - J76-16 (CANL) Ignition switch off 200 Ω or higher
J76-5 (CANH) - J17-4 (CG) Ignition switch off 200 Ω or higher
J76-16 (CANL) - J17-4 (CG) Ignition switch off 200 Ω or higher
J76-5 (CANH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
J76-16 (CANL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

NG

19.CONNECT CONNECTOR
13.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.
U152577E01
0.418,2.696 0.662,2.835 0.244,0.140 10 J17 0.552,1.091 0.795,1.231 0.243,0.140 10 J76 1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.215,1.291 2.374,1.489 2.374,1.489 2.472,1.489 false 2.511,0.937 2.396,0.937 2.396,0.937 2.215,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.533,0.86 2.953,1.002 0.420,0.142 10 CANH 2.498,1.403 2.922,1.545 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J76-1 (CANH) - J76-12 (CANL) Ignition switch off 108 to 132 Ω
J76-1 (CANH) - J17-4 (CG) Ignition switch off 200 Ω or higher
J76-12 (CANL) - J17-4 (CG) Ignition switch off 200 Ω or higher
J76-1 (CANH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
J76-12 (CANL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

14.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

21.CONNECT CONNECTOR
14.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U152578E01
0.418,2.696 0.662,2.835 0.244,0.140 10 J17 0.552,1.091 0.795,1.231 0.243,0.140 10 J76 1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.932,1.291 2.164,1.651 2.164,1.651 2.261,1.651 false 2.414,0.732 2.299,0.732 2.299,0.732 1.932,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.436,0.655 2.855,0.797 0.420,0.142 10 CANH 2.287,1.565 2.711,1.707 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J76-4 (CANH) - J76-15 (CANL) Ignition switch off 108 to 132 Ω
J76-4 (CANH) - J17-4 (CG) Ignition switch off 200 Ω or higher
J76-15 (CANL) - J17-4 (CG) Ignition switch off 200 Ω or higher
J76-4 (CANH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
J76-15 (CANL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

23.CONNECT CONNECTOR
15.CONNECT CONNECTOR
a.

Reconnect the J76 No. 3 junction connector.



NEXT

16.CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT CONTROL ECU AND SWITCH LH)
16.CHECK FOR SHORT IN CAN BUS WIRES (FRONT POWER SEAT CONTROL ECU AND SWITCH LH)
a.
U152450E01
2.546,1.533 2.980,1.711 0.434,0.178 10 CANN 2.282,1.484 2.441,1.618 2.441,1.618 2.525,1.618 false 2.459,1.774 2.892,1.952 0.434,0.178 10 CANP 2.199,1.484 2.35,1.861 2.35,1.861 2.434,1.861 false 1.201,1.243 1.458,1.383 0.257,0.140 10 Z10 0.351,2.696 0.674,2.874 0.324,0.178 10 J17 0.105,1.977 0.318,2.155 0.213,0.178 10 *b 2.673,3.114 3.106,3.292 0.434,0.178 10 BAT 2.355,3.045 2.559,3.209 2.559,3.209 2.646,3.209 false 0.105,0.017 0.318,0.195 0.213,0.178 10 *a 0.947,2.037 1.179,2.215 0.232,0.178 10 CG 1.731,2.579 1.399,2.134 1.399,2.134 1.239,2.134 false

Disconnect the Z10 front power seat control ECU and switch LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
Z10-8 (CANP) - Z10-7 (CANN) Ignition switch off 54 to 69 Ω
Z10-8 (CANP) - J17-4 (CG) Ignition switch off 200 Ω or higher
Z10-7 (CANN) - J17-4 (CG) Ignition switch off 200 Ω or higher
Z10-8 (CANP) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
Z10-7 (CANN) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Front Power Seat Control ECU and Switch LH)
*b Front view of DLC3



OK

REPLACE FRONT POWER SEAT CONTROL ECU AND SWITCH LH

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO FRONT POWER SEAT CONTROL ECU AND SWITCH LH (CANP, CANN)

17.CONNECT CONNECTOR
a.

Reconnect the J76 No. 3 junction connector.



NEXT

18.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)
18.CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)
a.
U152550E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.368,1.732 1.491,1.732 1.491,1.732 1.741,1.36 false 2.206,0.553 2.083,0.553 2.083,0.553 1.727,1.083 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.228,0.476 2.648,0.618 0.420,0.142 10 CANH 0.889,1.653 1.278,1.795 0.389,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.422,2.696 0.708,2.835 0.286,0.140 10 J17 0.422,1.127 0.696,1.267 0.274,0.140 10 J47 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Disconnect the J47 multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J47-5 (CANH) - J47-14 (CANL) Ignition switch off 54 to 69 Ω
J47-5 (CANH) - J17-4 (CG) Ignition switch off 200 Ω or higher
J47-14 (CANL) - J17-4 (CG) Ignition switch off 200 Ω or higher
J47-5 (CANH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
J47-14 (CANL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANH, CANL)

19.CONNECT CONNECTOR
a.

Reconnect the J76 No. 3 junction connector.



NEXT

20.CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU ASSEMBLY)
20.CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU ASSEMBLY)
a.
U152551E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 0.755,1.267 0.905,1.582 0.905,1.582 1.002,1.582 false 0.532,0.778 0.604,0.778 0.604,0.778 0.746,1.104 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.156,0.686 0.576,0.828 0.420,0.142 10 CAN 1.017,1.505 1.472,1.647 0.455,0.142 10 CGND 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.422,2.696 0.708,2.835 0.286,0.140 10 J17 1.602,0.367 1.818,0.507 0.216,0.140 10 N8 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Disconnect the N8 outer mirror control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
N8-1 (CAN) - N8-21 (CGND) Ignition switch off 54 to 69 Ω
N8-1 (CAN) - J17-4 (CG) Ignition switch off 200 Ω or higher
N8-21 (CGND) - J17-4 (CG) Ignition switch off 200 Ω or higher
N8-1 (CAN) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
N8-21 (CGND) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly)
*b Front view of DLC3



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU ASSEMBLY (CAN, CGND)

21.CONNECT CONNECTOR
a.

Reconnect the J76 No. 3 junction connector.



NEXT

22.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
22.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)
a.
U152511E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 1.221,0.922 1.022,0.412 1.022,0.412 0.839,0.412 false 0.85,0.696 0.974,0.696 0.974,0.696 1.135,0.922 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.3,0.335 0.743,0.477 0.443,0.142 10 MSCH 0.362,0.607 0.785,0.749 0.424,0.142 10 MSCL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.422,2.696 0.708,2.835 0.286,0.140 10 J17 2.8,0.441 3.074,0.581 0.274,0.140 10 J28 1.062,2.087 1.291,2.229 0.229,0.142 10 CG

Disconnect the J28 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J28-18 (MSCH) - J28-19 (MSCL) Ignition switch off 108 to 132 Ω
J28-18 (MSCH) - J17-4 (CG) Ignition switch off 200 Ω or higher
J28-19 (MSCL) - J17-4 (CG) Ignition switch off 200 Ω or higher
J28-18 (MSCH) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
J28-19 (MSCL) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)
*b Front view of DLC3



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (MSCH, MSCL)

23.CONNECT CONNECTOR
a.

Reconnect the J76 No. 3 junction connector.



NEXT

24.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
24.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U152522E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.005,1.457 2.172,1.596 2.172,1.596 2.269,1.596 false 2.236,1.11 2.164,1.11 2.164,1.11 1.89,1.364 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.258,1.033 2.678,1.175 0.420,0.142 10 CANN 2.295,1.51 2.719,1.652 0.424,0.142 10 CANP 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.422,2.696 0.708,2.835 0.286,0.140 10 J17 1.062,2.087 1.291,2.229 0.229,0.142 10 CG 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.685,1.129 0.880,1.268 0.195,0.140 10 J2

Disconnect the J2 main body ECU (driver side junction block assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
J2-16 (CANP) - J2-15 (CANN) Ignition switch off 108 to 132 Ω
J2-16 (CANP) - J17-4 (CG) Ignition switch off 200 Ω or higher
J2-15 (CANN) - J17-4 (CG) Ignition switch off 200 Ω or higher
J2-16 (CANP) - J17-16 (BAT) Ignition switch off 6 kΩ or higher
J2-15 (CANN) - J17-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Driver Side Junction Block Assembly])
*b Front view of DLC3



OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)

25.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

U152728E01
0.227,0.14 0.464,0.363 0.237,0.223 10 *a 1.043,0.796 1.255,0.940 0.211,0.144 10 DA 0.268,2.441 0.726,2.594 0.458,0.152 10 ALTB 6.279,0.975 6.699,1.137 0.420,0.163 10 ACC 6.46,1.203 6.880,1.366 0.420,0.163 10 IG 1.038,2.043 0.753,2.505 0.753,2.505 0.62,2.505 false 3.189,1.064 3.401,1.208 0.211,0.144 10 DB 5.45,1.064 5.669,1.208 0.218,0.144 10 DD 2.712,2.231 3.149,2.390 0.437,0.159 10 BECU 2.467,1.828 2.565,2.291 2.565,2.291 2.698,2.291 false 3.735,2.231 4.172,2.390 0.437,0.159 10 GND1 3.517,1.94 3.587,2.291 3.587,2.291 3.721,2.291 false 6.019,1.743 6.304,1.28 6.304,1.28 6.437,1.28 false 5.847,1.745 6.12,1.039 6.12,1.039 6.254,1.039 false

Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Driver Side Junction Block Assembly])
- -

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the DA, DB and DD main body ECU (driver side junction block assembly) connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DB-21 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DA-1 (ALTB) - Body ground Always 11 to 14 V
DB-13 (BECU) - Body ground Always 11 to 14 V
DD-43 (IG) - Body ground Ignition switch ON 11 to 14 V
DD-45 (ACC) - Body ground Ignition switch ACC 11 to 14 V




OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR