Home › Engine / Hybrid System › 3UR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2016.08
RM27M0U _51 Engine / Hybrid System _049106 3UR-FE ENGINE MECHANICAL _0234028 ENGINE UNIT A

3UR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the No. 1 camshaft, No. 2 camshaft, No. 3 camshaft, No. 4 camshaft, camshaft timing gear LH , camshaft timing gear RH, camshaft timing exhaust gear LH or camshaft timing exhaust gear RH (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


PROCEDURE

Hide 1.INSTALL STUD BOLT

A163193E01
1.889,2.233 3.144,2.422 1.254,0.188 10 24.5 mm (0.965 in.) 1.594,2.946 2.787,3.134 1.193,0.188 10 40 mm (1.58 in.) 1.883,2.533 3.061,2.721 1.178,0.188 10 14 mm (0.551 in.) 1.316,2.785 1.835,2.329 false 1.316,3.143 1.846,2.638 false

a.

Install the timing chain cover stud bolt.

i.

Using an E10 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



b.
A165519E04
0.656,3.344 0.865,3.948 0.865,3.948 0.656,3.719 false 2.281,3.76 2.594,3.979 false 1.917,2.979 2.115,2.979 2.115,2.979 2.281,3.427 false 1.438,0.094 1.583,0.281 0.146,0.188 10 false A 0.156,1.156 0.302,1.344 0.146,0.188 10 false A 2.125,2.25 2.302,2.458 0.177,0.208 10 false B 0.271,3.969 1.417,4.167 1.146,0.198 10 false 9 mm (0.354 in.) 0.969,3.333 1.677,3.771 0.708,0.438 10 false 19 mm (0.748 in.) 1.917,4 3.063,4.198 1.146,0.198 10 false 12 mm (0.472 in.) 0.5,2.885 1.677,3.146 1.177,0.26 10 false 22 mm (0.866 in.) 2.615,3.323 3.271,3.719 0.656,0.396 10 false 39 mm (1.54 in.) 0.271,2.563 0.469,2.76 0.198,0.198 10 false A: 1.896,2.563 2.063,2.76 0.167,0.198 10 false B:

Install the oil pan stud bolt.

i.

Using an E6 and E7 "TORX" socket wrench, install the 3 stud bolts as shown in the illustration.

Torque:
for stud bolt A : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for stud bolt B : 9.0 N*m (92 kgf*cm, 80 in.*lbf)



Hide 2.INSTALL RING PIN

A160726E01
0.367,1.451 0.506,1.622 0.140,0.171 10 A 0.578,1.945 0.718,2.116 0.140,0.171 10 A 2.786,1.434 2.913,1.599 0.127,0.165 10 B 2.811,1.832 2.938,2.000 0.127,0.168 10 B 0.837,2.75 1.750,2.934 0.913,0.184 10 7.5 to 8.5 mm 2.329,2.613 3.221,2.797 0.892,0.184 10 3.6 to 4.6 mm 0.213,2.335 0.385,2.506 0.172,0.171 10 A: 1.668,2.335 1.823,2.500 0.155,0.165 10 B:

a.

Using a plastic-faced hammer, tap in new ring pins to the timing chain cover.

Standard protrusion:
Item Ring Pin Diameter Specified Condition
Ring pin A 13 mm (0.512 in.) 7.5 to 8.5 mm (0.295 to 0.335 in.)
Ring pin B 11 mm (0.433 in.) 3.6 to 4.6 mm (0.142 to 0.181 in.)



Hide 11381A 3.INSTALL REAR CRANKSHAFT OIL SEAL

a.
A148433E01
0.141,0.746 0.509,0.988 0.367,0.242 10 SST 1.132,0.981 0.512,0.846 0.512,0.846 1.052,1.52 false

Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07100)

Standard depth:

0 to 1.0 mm (0 to 0.0394 in.)


NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap on the oil seal at an angle.




Hide 12109A 4.INSTALL OIL DRAIN PIPE SUB-ASSEMBLY

A160728

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the drain pipe.


c.

Install the oil drain pipe with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11381 5.INSTALL ENGINE REAR OIL SEAL RETAINER

A148434E12
3.104,1.698 3.063,1.448 false 0.365,1.688 0.344,1.458 false 0.729,0.094 2.656,0.281 1.927,0.188 10 false Seal diameter: 2.0 to 3.0 mm 2.833,1.688 3.323,1.865 0.49,0.177 10 false 3.5 mm 0.167,1.708 0.656,1.885 0.49,0.177 10 false 3.5 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


Application position from inside edge of retainer:

3.5 mm (0.138 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the engine rear oil seal retainer within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A145612

Install the oil seal retainer with the 6 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Do not start the engine for at least 2 hours after installing.

·

When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.

·

When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.




Hide 15104 6.INSTALL OIL STRAINER SUB-ASSEMBLY

A160724

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the oil strainer.


c.

Install the oil strainer with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Make sure the O-ring is not twisted or damaged.



Hide 12121 7.INSTALL NO. 1 OIL PAN BAFFLE PLATE

A160723

a.

Install the baffle plate with the 7 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12101 8.INSTALL NO. 1 OIL PAN SUB-ASSEMBLY

A160729E05
0.531,0.052 2.49,0.479 1.958,0.427 10 true Seal diameter: 3.0 to 4.0 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A160721E06
3.094,1.063 3.229,1.219 0.135,0.156 10 false A 2.313,1.781 2.448,1.938 0.135,0.156 10 true B 2.99,1.427 3.24,1.583 0.25,0.156 10 false Nut 1.146,0.813 1.417,1.146 0.271,0.333 10 true Nut 3.083,0.698 3.219,0.854 0.135,0.156 10 false A 1.875,1.823 2.01,1.979 0.135,0.156 10 true B 1.479,1.833 1.615,1.99 0.135,0.156 10 true B 1.188,1.833 1.323,1.99 0.135,0.156 10 true B 0.896,1.792 1.031,1.948 0.135,0.156 10 true B 0.302,1.458 0.438,1.615 0.135,0.156 10 false B 2.99,0.26 3.125,0.417 0.135,0.156 10 false B 2.219,0.021 2.354,0.177 0.135,0.156 10 false B 1.875,0.021 2.01,0.177 0.135,0.156 10 false B 1.438,0.031 1.573,0.188 0.135,0.156 10 true B 0.979,0.031 1.115,0.188 0.135,0.156 10 false B 0.292,0.26 0.427,0.417 0.135,0.156 10 false B

Install the oil pan with the 14 bolts and 2 nuts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B : 35 N*m (357 kgf*cm, 26 ft.*lbf)
for nut : 35 N*m (357 kgf*cm, 26 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after installing.



Hide 12102A 9.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

A160730E01
0.516,0.049 2.388,0.232 1.872,0.184 10 Seal diameter: 3.0 to 4.0 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.156 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A160720E04
2.885,0.531 3.156,0.708 0.271,0.177 10 false Nut 1.448,1.719 1.719,1.896 0.271,0.177 10 true Nut

Install the oil pan with the 14 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after installing.



Hide 16877 10.INSTALL NO. 1 HEAT EXCHANGER COVER

A161918E01
0.671,0.002 2.533,0.193 1.863,0.191 10 Seal diameter: 3.0 to 4.0 mm

a.

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 1 heat exchanger cover within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A161916E05
2.448,1.75 2.688,1.896 0.24,0.146 9 true Nut 0.646,1.896 0.885,2.042 0.24,0.146 9 true Nut 0.771,0.219 0.906,0.385 0.135,0.167 10 true A 0.49,1.438 0.625,1.604 0.135,0.167 10 true B 3.156,1.573 3.292,1.74 0.135,0.167 10 false C 1.188,0.115 1.323,0.281 0.135,0.167 10 true A 1.729,0.115 1.865,0.281 0.135,0.167 10 true A 2.125,0.094 2.26,0.26 0.135,0.167 10 true A 2.594,0.135 2.729,0.302 0.135,0.167 10 true A 2.99,0.333 3.125,0.5 0.135,0.167 10 true A 1.052,1.885 1.188,2.052 0.135,0.167 10 true A 1.635,1.885 1.771,2.052 0.135,0.167 10 true A 1.979,1.885 2.115,2.052 0.135,0.167 10 true A 3.292,0.979 3.427,1.146 0.135,0.167 10 false A

Install the heat exchanger cover with the 12 bolts and 2 nuts.

Torque:
for bolt C : 10 N*m (102 kgf*cm, 7 ft.*lbf)
except bolt C : 21 N*m (214 kgf*cm, 16 ft.*lbf)

Standard Bolt:
Item Length Thread Diameter
Bolt A 20 mm (0.787 in.) 8 mm (0.315 in.)
Bolt B 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt C 16 mm (0.630 in.) 6 mm (0.236 in.)


NOTICE:

Do not start the engine for at least 2 hours after installing.



Hide 12203A 11.INSTALL VENTILATION PIPE GASKET

A163596E03
1.344,1.271 0.896,1.448 0.896,1.448 1.333,1.521 true 0.51,1.396 0.802,1.583 0.292,0.188 10 true SST

a.

Using SST, evenly tap in a new ventilation pipe gasket until its surface is flush with the lip of the ventilation pipe.

SST
09950-60010  (09951-00360)
09950-70010  (09951-07100)

NOTICE:
·

Do not tap the gasket at an angle.

·

Do not tap the gasket excessively.




Hide 12209E 12.INSTALL OIL RETURN PIPE GASKET

A163394

a.

Install a new oil return pipe gasket.


Hide 11445 13.INSTALL CYLINDER BLOCK WATER JACKET SPACER

A161997E01
0.073,0.13 0.695,0.336 0.621,0.207 10 Up Mark 0.775,0.937 0.8,0.231 0.8,0.231 2.507,0.729 false

a.

Install the 2 water jacket spacers as shown in the illustration.

NOTICE:
·

Face the cutouts indicated by the arrows in illustration away from the engine.

·

Face the "up mark" as shown in the illustration.




Hide 13716 18.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem caps.


b.

Install the 32 valve stem caps to the cylinder head.


Hide 13750 19.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

b.

Install the 32 valve lash adjusters to the cylinder head.

NOTICE:

Install the lash adjuster at the same place it was removed from.



Hide 13801 20.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Apply engine oil to the lash adjuster tips and valve stem cap ends.


b.
A386787E01
0.74,1.042 0.823,1.042 0.823,1.042 1.031,1.094 false 2.094,0.188 1.865,0.188 1.865,0.188 1.615,0.396 false 2.458,1.125 2.667,1.125 true 2.146,0.094 3.365,0.281 1.219,0.188 10 false Valve Rocker Arm 2.708,1.031 3.417,1.385 0.708,0.354 10 false Valve Lash Adjuster 0.01,0.948 0.771,1.344 0.76,0.396 10 false Valve Stem Cap

Install the 32 valve rocker arms as shown in the illustration.


Hide 21.INSTALL CAMSHAFT BEARING CAP RH

HINT:

Perform "Inspection After Repairs" after replacing the No. 1 or No. 2 camshaft sub-assembly (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


b.
A316364E01
0.006,0.007 1.179,0.187 1.173,0.180 10 Identification Mark 1.446,0.097 1.627,0.097 1.627,0.097 1.275,1.408 false 1.625,0.097 0.919,0.834 false

Install the No. 1 and No. 2 camshafts to the camshaft housing.

HINT:

Check the identification mark stamped on the camshaft.

Item Mark
for Intake Side NO. 1
for Exhaust Side NO. 2



c.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.


d.
A160687E05
2.792,1.708 2.906,1.875 0.115,0.167 10 true 1 2.823,0.208 2.938,0.375 0.115,0.167 10 true 2 2.104,1.719 2.219,1.885 0.115,0.167 10 true 3 2.104,0.24 2.219,0.406 0.115,0.167 10 false 4 1.552,1.719 1.667,1.885 0.115,0.167 10 true 5 1.552,0.208 1.667,0.375 0.115,0.167 10 false 6 1.01,1.719 1.125,1.885 0.115,0.167 10 true 7 1,0.219 1.115,0.385 0.115,0.167 10 false 8 0.354,1.719 0.469,1.885 0.115,0.167 10 false 9 0.313,0.229 0.5,0.396 0.188,0.167 10 false 10

Temporarily install the 10 bolts in the order shown in the illustration.


Hide 11103C 22.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

A386786E01
0.896,0.604 1.385,0.604 false 2.375,0.604 2.917,0.604 2.917,0.604 2.917,0.792 false 2.052,0.219 2.208,0.219 false 0.146,0.5 0.885,0.885 0.74,0.385 10 false Valve Lash Adjuster 2.583,0.823 3.365,1.208 0.781,0.385 10 false Valve Stem Cap 2.24,0.125 3.427,0.313 1.188,0.188 10 false Valve Rocker Arm

a.

Make sure that the valve rocker arms are installed as shown in the illustration.


b.
A380007E01
0.729,1.708 2.625,1.927 1.896,0.219 10 false Seal diameter: 3.5 to 4.0 mm

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.0 mm (0.138 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
A163556E06
0.865,2.625 1.698,2.938 1.698,2.938 2.25,2.729 false 1.479,1.323 1.573,1.479 0.094,0.156 10 true 1 0.854,1.323 0.948,1.479 0.094,0.156 10 true 2 1.979,1.313 2.073,1.469 0.094,0.156 10 true 3 0.219,1.344 0.313,1.5 0.094,0.156 10 true 4 2.625,1.313 2.719,1.469 0.094,0.156 10 true 5 1.427,1.896 1.521,2.052 0.094,0.156 10 false 6 1.365,0 1.458,0.156 0.094,0.156 10 false 7 0.875,1.885 0.969,2.042 0.094,0.156 10 false 8 0.844,0 0.938,0.156 0.094,0.156 10 false 9 1.948,1.896 2.135,2.052 0.188,0.156 10 false 10 1.917,0 2.104,0.156 0.188,0.156 10 false 11 0.177,1.896 0.365,2.052 0.188,0.156 10 false 12 0.188,0 0.375,0.156 0.188,0.156 10 false 13 3.042,1.313 3.229,1.469 0.188,0.156 10 false 14 2.49,0.063 2.677,0.219 0.188,0.156 10 false 15 3.115,0 3.302,0.156 0.188,0.156 10 false 17 2.333,1.677 2.521,1.833 0.188,0.156 10 true 18 0.021,0.406 0.208,0.563 0.188,0.156 10 true 16 1.323,2.958 2.021,3.125 0.698,0.167 10 false Knock Pin 0.573,2.125 0.948,2.323 0.375,0.198 10 false 55° 2,2.219 2.375,2.417 0.375,0.198 10 false 70° 1.281,2.146 1.531,2.344 0.25,0.198 10 false EX 2.667,2.125 2.917,2.323 0.25,0.198 10 false IN 2.802,1.875 2.927,2.042 0.125,0.167 10 false A

Install the camshaft housing, and install the 18 bolts in the order shown in the illustration.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for except bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Do not start the engine for at least 2 hours after the installation.

·

Make sure that the knock pin of the camshaft is positioned as shown in the illustration before installing the camshaft housing.




d.
A160684E11
2.823,1.646 2.938,1.802 0.115,0.156 10 true 1 2.802,0.198 2.917,0.354 0.115,0.156 10 true 2 2.125,1.646 2.24,1.802 0.115,0.156 10 true 3 2.104,0.219 2.219,0.375 0.115,0.156 10 true 4 1.563,1.646 1.677,1.802 0.115,0.156 10 true 5 1.552,0.208 1.667,0.365 0.115,0.156 10 false 6 0.99,1.646 1.104,1.802 0.115,0.156 10 true 7 0.969,0.188 1.083,0.344 0.115,0.156 10 false 8 0.365,1.646 0.479,1.802 0.115,0.156 10 true 9 0.313,0.198 0.5,0.354 0.188,0.156 10 false 10

Tighten the 10 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.



Hide 23.INSTALL CAMSHAFT BEARING CAP LH

HINT:

Perform "Inspection After Repairs" after replacing the No. 3 or No. 4 camshaft (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


a.

Apply a light coat of engine oil to the camshaft journals, camshaft housings and bearing caps.


b.
A316365E01
1.991,0.021 3.161,0.205 1.170,0.185 10 Identification Mark 1.96,0.105 1.702,0.105 1.702,0.105 1.889,1.297 false 1.702,0.105 2.212,0.777 false

Install the No. 3 and No. 4 camshafts to the camshaft housing.

HINT:

Check the identification mark stamped on the camshaft.

Item Mark
for Intake Side NO. 3
for Exhaust Side NO. 4



c.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.


d.
U151457E02
0.615,1.75 0.719,1.896 0.104,0.146 10 true 1 0.594,0.26 0.698,0.406 0.104,0.146 10 true 2 1.229,1.781 1.333,1.927 0.104,0.146 10 true 3 1.219,0.25 1.323,0.396 0.104,0.146 10 false 4 1.708,1.781 1.813,1.927 0.104,0.146 10 false 5 1.688,0.25 1.792,0.396 0.104,0.146 10 false 6 2.198,1.771 2.302,1.917 0.104,0.146 10 true 7 2.188,0.271 2.292,0.417 0.104,0.146 10 false 8 2.75,1.75 2.865,1.896 0.115,0.146 10 false 9 2.698,0.271 2.885,0.427 0.188,0.156 10 false 10

Temporarily install the 10 bolts in the order shown in the illustration.


Hide 11104A 24.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A386786E01
0.896,0.604 1.385,0.604 false 2.375,0.604 2.917,0.604 2.917,0.604 2.917,0.792 false 2.052,0.219 2.208,0.219 false 0.146,0.5 0.885,0.885 0.74,0.385 10 false Valve Lash Adjuster 2.583,0.823 3.365,1.208 0.781,0.385 10 false Valve Stem Cap 2.24,0.125 3.427,0.313 1.188,0.188 10 false Valve Rocker Arm

Install the valve rocker arms as shown in the illustration.


b.
A380006E01
0.781,1.688 2.594,1.906 1.813,0.219 10 false Seal diameter: 3.5 to 4.0 mm

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.0 mm (0.138 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
A163732E06
0.917,2.583 1.813,2.938 1.813,2.938 2.51,2.573 false 1.51,0.552 1.615,0.708 0.104,0.156 10 true 1 1.042,0.552 1.146,0.708 0.104,0.156 10 true 2 2.156,0.552 2.26,0.708 0.104,0.156 10 true 3 0.406,0.563 0.51,0.719 0.104,0.156 10 true 4 2.802,0.552 2.948,0.719 0.146,0.167 10 true 5 1.604,0 1.708,0.156 0.104,0.156 10 false 6 1.521,1.885 1.625,2.042 0.104,0.156 10 false 7 1.042,0 1.146,0.156 0.104,0.156 10 false 8 1.031,1.885 1.135,2.042 0.104,0.156 10 false 9 2.135,0 2.323,0.156 0.188,0.156 10 false 10 2.083,1.885 2.271,2.042 0.188,0.156 10 false 11 0.354,0 0.542,0.156 0.188,0.156 10 false 12 0.365,1.885 0.552,2.042 0.188,0.156 10 false 13 3.208,0.531 3.396,0.688 0.188,0.156 10 false 14 2.646,1.844 2.833,2 0.188,0.156 10 false 15 0.052,1.406 0.24,1.563 0.188,0.156 10 false 16 2.979,1.438 3.167,1.594 0.188,0.156 10 false 17 1.302,2.094 1.49,2.271 0.188,0.177 10 false IN 2.875,2.125 3.146,2.26 0.271,0.135 10 false EX 1.448,2.927 2.125,3.094 0.677,0.167 10 false Knock Pin 2.5,2.073 2.781,2.25 0.281,0.177 10 false 3° 0.698,2.083 1.01,2.292 0.313,0.208 10 false 45° 3.208,0.021 3.396,0.177 0.188,0.156 10 false 18 2.885,0.021 3.021,0.188 0.135,0.167 10 false A

Install the camshaft housing, and install the 18 bolts in the order shown in the illustration.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for except bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Do not start the engine for at least 2 hours after the installation.

·

Make sure that the knock pin of the camshaft is positioned as shown in the illustration before installing the camshaft housing.




d.
A163592E09
2.885,0.208 3,0.396 0.115,0.188 10 true 1 2.875,1.729 2.99,1.917 0.115,0.188 10 true 2 2.188,0.198 2.302,0.385 0.115,0.188 10 true 3 2.156,1.729 2.271,1.917 0.115,0.188 10 false 4 1.625,0.198 1.74,0.385 0.115,0.188 10 true 5 1.604,1.729 1.719,1.917 0.115,0.188 10 false 6 1.073,0.208 1.188,0.396 0.115,0.188 10 true 7 1.021,1.729 1.135,1.917 0.115,0.188 10 false 8 0.438,0.219 0.552,0.406 0.115,0.188 10 true 9 0.385,1.729 0.563,1.917 0.177,0.188 10 false 10

Tighten the 10 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.



Hide 13521A 25.INSTALL CRANKSHAFT TIMING GEAR KEY

A164296

a.

Install the timing gear key.

HINT:

The other timing gear key will be installed at a later step.



Hide 13550 26.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

A148228E07
2.01,2.646 2.917,2.417 2.917,2.417 2.792,1.667 true 1.406,2.698 1.531,2.896 false 2.469,0.927 2.875,1.344 0.406,0.417 10 true Push 2.958,2.313 3.198,2.479 0.24,0.167 10 false Pin 1.24,2.906 1.74,3.073 0.5,0.167 10 false Plunger

a.

Install the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.


Hide 13506 27.INSTALL NO. 1 CHAIN SUB-ASSEMBLY RH

HINT:

Perform "Inspection After Repairs" after replacing the No. 1 or No. 2 camshaft sub-assembly or camshaft timing gear RH or camshaft timing exhaust gear RH (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


A198566E03
1.781,0.219 1.979,0.219 1.979,0.219 2.385,0.604 false 2.375,0.708 2.375,1.208 false 0.906,0.115 1.646,0.323 0.74,0.208 10 false Mark Plate 1.958,1.208 2.865,1.458 0.906,0.25 10 true Timing Mark

a.

Align the No. 1 chain's orange mark plate with the camshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.


b.
A149461E09
2.385,1.708 1.99,1.844 true 1.885,1.771 1.135,1.604 true 0.271,1.521 1.063,1.698 0.792,0.177 10 false Timing Mark 2.438,1.625 3.156,1.792 0.719,0.167 10 false Mark Plate

Align the No. 1 chain's orange mark plate with the crankshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.


c.
A160663E08
0.854,1.115 1.979,1.885 1.979,1.885 2.75,1.115 true 0.885,0.771 1.198,0.156 1.198,0.156 1.333,0.156 false 2.385,0.167 2.531,0.167 2.531,0.167 2.74,0.833 false 1.573,1.927 2.313,2.094 0.74,0.167 10 false Mark Plate 1.448,0.083 2.302,0.281 0.854,0.198 10 false Timing Mark

Align the No. 2 chain's mark plates (yellow) with the timing marks of the camshaft timing gear and camshaft timing exhaust gear, and attach the No. 2 chain to the gears as shown in the illustration.

NOTICE:

The camshaft timing exhaust gear has 2 grooves. Align the mark plates of the No. 2 chain with the first groove.


HINT:

The crankshaft timing gear and camshaft exhaust gear will be installed with the No. 1 and No. 2 chains connected to the gears.



d.

Install the crankshaft timing sprocket to the crankshaft.


e.

Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear.


f.

Using the hexagonal portion of the No. 2 camshaft, align and attach the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear.


g.

Remove the pin from the No. 2 chain tensioner.


Hide 13561 28.INSTALL NO. 1 CHAIN VIBRATION DAMPER RH

A160658

a.

Install the vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13559 29.INSTALL NO. 1 CHAIN TENSIONER SLIPPER RH

A178486

HINT:

If you cannot install the chain tensioner slipper due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain, and then install the chain tensioner slipper.


Hide 13540 30.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY RH

A148260E01
2.712,1.388 3.255,1.572 0.543,0.184 10 Plunger 0.1,0.606 0.973,0.794 0.873,0.188 10 Stopper Plate 2.425,1.1 2.682,1.467 2.682,1.467 1.951,1.72 false 1.996,0.979 1.174,0.693 1.174,0.693 1.361,1.403 false

a.

Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.


c.
A150146

Install the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the hexagon wrench from the chain tensioner.


Hide 13560A 31.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

A148227E06
1.99,1.802 1.875,1.802 1.875,1.802 1.813,2.188 false 1.292,2.542 1.979,2.365 false 2.479,0.333 3.021,0.583 0.542,0.25 10 true Push 2.052,1.729 2.292,1.896 0.24,0.167 10 false Pin 0.719,2.448 1.281,2.656 0.563,0.208 10 false Plunger

a.

Install the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

While pushing down the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.


Hide 13506 32.INSTALL NO. 1 CHAIN SUB-ASSEMBLY LH

HINT:

Perform "Inspection After Repairs" after replacing the camshaft timing gear LH or camshaft timing exhaust gear LH (See page Engine / Hybrid System>3UR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).


A198567E03
1.094,0.656 1.406,0.188 1.406,0.188 1.604,0.188 true 1.104,0.74 1.104,1.167 false 1.646,0.104 2.385,0.302 0.74,0.198 10 false Mark Plate 0.656,1.167 1.531,1.542 0.875,0.375 10 true Timing Mark

a.

Align the No. 1 chain's orange mark plate with the camshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.


b.
A149462E11
2.333,1.563 1.813,1.698 false 1.677,1.479 1.188,1.427 true 0.354,1.313 1.146,1.49 0.792,0.177 10 false Timing Mark 2.365,1.479 3.083,1.646 0.719,0.167 10 false Mark Plate

Align the No. 1 chain's orange mark plate with the crankshaft timing gear's timing mark, and attach the chain to the gear as shown in the illustration.


c.
A160666E08
0.813,0.802 1,0.135 1,0.135 1.115,0.135 false 2.135,0.115 2.24,0.115 2.24,0.115 2.458,0.667 false 0.792,1.104 1.594,1.906 1.594,1.906 2.479,1 true 1.229,0.063 2.063,0.271 0.833,0.208 10 false Timing Mark 1.208,1.958 1.979,2.135 0.771,0.177 10 true Mark Plate

Align the No. 2 chain's mark plates (yellow) with the timing marks of the camshaft timing gear and camshaft timing exhaust gear, and attach the No. 2 chain to the gears as shown in the illustration.

NOTICE:

The camshaft timing exhaust gear has 2 grooves. Align the mark plates of the No. 2 chain with the first groove.


HINT:

The crankshaft timing gear and camshaft exhaust gear will be installed with the No. 1 and No. 2 chains connected to the gears.



d.

Install the crankshaft timing sprocket to the crankshaft.


e.

Align and attach the knock pin of the No. 3 camshaft with the pin hole of the camshaft timing gear.


f.

Using the hexagonal portion of the No. 4 camshaft, align and attach the knock pin of the No. 4 camshaft with the pin hole of the camshaft timing exhaust gear.

NOTICE:

Because the gears' timing mark positions may shift due to looseness of the No. 1 chain, use the hexagonal portion of the camshaft to hold the No. 3 camshaft in place until the No. 1 chain tensioner is installed.



g.

Remove the pin from the No. 2 chain tensioner.


Hide 13559 33.INSTALL NO. 1 CHAIN TENSIONER SLIPPER LH

A178487

HINT:

If you cannot install the chain tensioner slipper due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain and install the chain tensioner.


Hide 13540 34.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY LH

A148260E01
2.712,1.388 3.255,1.572 0.543,0.184 10 Plunger 0.1,0.606 0.973,0.794 0.873,0.188 10 Stopper Plate 2.425,1.1 2.682,1.467 2.682,1.467 1.951,1.72 false 1.996,0.979 1.174,0.693 1.174,0.693 1.361,1.403 false

a.

Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.


c.
A160733

Install a new gasket and the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13561 35.INSTALL NO. 1 CHAIN VIBRATION DAMPER LH

A178533

a.

Install the vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Remove the hexagon wrench from the No. 1 chain tensioner.


Hide 13050 36.TIGHTEN CAMSHAFT TIMING GEAR

A161993E03
2.979,0.042 3.323,0.333 0.344,0.292 10 true Hold 0.698,0.042 1.042,0.229 0.344,0.188 10 false Turn

a.

LH:

i.

Using a wrench to hold the hexagonal portion of the No. 3 camshaft, tighten the camshaft timing gear with the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


ii.
A161994E03
0.854,0.406 1.188,0.615 0.333,0.208 10 true Turn 3.063,0.552 3.385,0.792 0.323,0.24 10 true Hold

Using a wrench to hold the hexagonal portion of the No. 4 camshaft, tighten the camshaft timing exhaust gear with the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)



b.
A161995E03
2.698,0.5 3.094,0.896 0.396,0.396 10 true Turn 1.292,0.042 1.646,0.25 0.354,0.208 10 false Hold

RH:

i.

Using a wrench to hold the hexagonal portion of the No. 1 camshaft, tighten the camshaft timing gear with the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


ii.
A161996E03
2.469,0.958 2.865,1.333 0.396,0.375 10 true Turn 0.958,0.083 1.292,0.438 0.333,0.354 10 true Hold

Using a wrench to hold the hexagonal portion of the No. 2 camshaft, tighten the camshaft timing exhaust gear with the bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)



Hide 37.CHECK NO. 1 CYLINDER TO TDC / COMPRESSION

a.

Temporarily install the pulley set bolt.


b.

Rotate the crankshaft clockwise, and check that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.


c.

Remove the crankshaft pulley bolt.

A160654E04
3.49,4.823 4.021,5.063 4.021,5.063 4.021,5.177 false 3.656,4.396 4.052,4.01 4.052,4.01 4.177,4.01 false 0.625,0.302 0.438,0.302 0.438,0.302 0.542,0.885 true 1.5,0.323 1.719,0.323 1.719,0.323 1.667,0.792 true 5.646,0.323 5.49,0.323 5.49,0.323 5.563,0.813 true 6.51,0.333 6.76,0.333 6.76,0.333 6.698,0.948 true 0.542,5.604 0.813,6.146 0.813,6.146 1.354,5.604 true 0.333,4.427 0.229,4.427 0.229,4.427 0.531,5.365 false 0.531,3.385 1.042,4.094 1.042,4.094 1.375,3.479 true 5.833,5.604 6.094,6.177 6.094,6.177 6.563,5.604 false 5.323,4.656 5.073,4.656 5.073,4.656 5.542,5.26 false 6.365,4.427 6.875,4.427 6.875,4.427 6.615,5.354 false 5.469,3.708 5.99,4.125 5.99,4.125 6.458,3.5 true 0.604,3.208 0.354,2.385 0.354,2.385 0.458,2.385 true 1.74,3.188 2.042,2.385 2.042,2.385 1.906,2.385 true 5.417,3.229 5.177,2.458 5.177,2.458 5.281,2.458 true 6.552,3.281 6.854,2.479 6.854,2.479 6.719,2.479 true 1.396,5.375 1.74,4.948 1.74,4.948 1.635,4.948 false 1.667,5.26 2.083,4.688 2.083,4.688 1.99,4.688 false 1.813,5.302 1.99,5.51 1.99,5.51 1.99,5.781 false 5.385,5.292 5.281,5.438 5.281,5.438 5.281,5.667 false 5.563,4.906 5.448,4.906 5.448,4.906 5.823,5.375 false 3.656,5.198 4.51,5.365 0.854,0.167 10 false Timing Mark 4.229,3.927 4.542,4.125 0.313,0.198 10 false Key 0.688,0.25 1.521,0.427 0.833,0.177 10 false Timing Mark 5.708,0.25 6.542,0.427 0.833,0.177 10 false Timing Mark 0.198,6.177 1.573,6.385 1.375,0.208 10 false Timing Mark Position 0.5,4.083 1.75,4.385 1.25,0.302 10 true Knock Pin Position 5.375,4.583 6.604,4.833 1.229,0.25 10 false Approximately 45° 5.604,4.823 6.833,5.073 1.229,0.25 10 false Approximately 32° 5.5,6.208 6.875,6.417 1.375,0.208 10 false Timing Mark Position 5.427,4.146 6.677,4.354 1.25,0.208 10 true Knock Pin Position 0.521,2.313 1.896,2.49 1.375,0.177 10 false Timing Mark Position 5.354,2.396 6.729,2.573 1.375,0.177 10 false Timing Mark Position 0.365,4.365 1.594,4.615 1.229,0.25 10 true Approximately 2° 0.479,4.885 1.708,5.135 1.229,0.25 10 false Approximately 16° 0.802,4.625 2.031,4.875 1.229,0.25 10 false Approximately 45° 1.708,5.813 2.198,6.188 0.49,0.375 10 false Toward Ceiling 5.031,5.667 5.521,6.042 0.49,0.375 10 false Toward Ceiling 5.167,4.344 6.396,4.594 1.229,0.25 10 true Approximately 18° 3.094,1.104 4.115,1.479 1.021,0.375 10 false Toward Ceiling


Hide 11302 39.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11301C 41.INSTALL FRONT CRANKSHAFT OIL SEAL

a.
A163995E07
1.771,2.635 1.854,3.01 true 1.854,3.01 1.927,2.604 true 1.688,3.031 2.01,3.208 0.323,0.177 10 true SST

Apply MP grease to the lip of a new oil seal.


b.

Using SST and a hammer, tap in the oil seal to a depth between 0 to 1.0 mm (0 to 0.0394 in.) from the timing chain cover edge.

SST
09223-22010  
09506-35010  

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap oil seal at an angle.




Hide 13521A 42.INSTALL CRANKSHAFT TIMING GEAR KEY

a.
A163993

Install the crankshaft timing gear key to the crankshaft.


Hide 11193 43.INSTALL SPARK PLUG TUBE GASKET

A380019E01
0.552,1.885 2.844,2.083 2.292,0.198 10 false Area to cut off

a.

Using a cutter knife, cut off the seal part of the removed gasket.


b.
A164316E04
1.167,0.594 1.271,0.344 1.271,0.344 1.396,0.344 false 1.688,1.156 1.688,1.5 true 1.427,0.281 2.594,0.51 1.167,0.229 10 false Removed Gasket 1.333,1.542 2.188,1.75 0.854,0.208 10 false New Gasket

Using the removed gasket and a hammer, tap in a new gasket until it stops.

HINT:

If the removed gasket does not fit on the new one, correct the removed one with pliers.



c.

Apply a light coat of MP grease to the gasket lip.


d.

Return the 4 ventilation baffle plate claws to the original positions.


Hide 15678A 44.INSTALL OIL CONTROL VALVE FILTER

A164313E08
2.49,0.885 2.49,1.302 false 2.813,0.115 2.969,0.115 2.969,0.115 3.125,0.896 true 1.708,0.427 2.167,0.427 2.167,0.427 2.813,0.802 true 2.313,1.302 2.708,1.542 0.396,0.24 10 false Filter 1.156,0.344 1.698,0.531 0.542,0.188 10 true Gasket 0.885,0.031 2.813,0.323 1.927,0.292 10 true Cylinder Head Cover Spacer

a.

LH:

i.

Install the valve filter in the cylinder head cover.


ii.

Install a new gasket and the cylinder head cover spacer with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.
A164314E08
0.917,0.781 0.917,1.208 false 0.281,0.792 0.635,0.115 0.635,0.115 0.771,0.115 true 0.625,0.688 0.99,0.406 0.99,0.406 1.917,0.406 true 0.75,1.271 1.125,1.479 0.375,0.208 10 false Filter 1.958,0.323 2.458,0.531 0.5,0.208 10 true Gasket 0.802,0.042 2.656,0.25 1.854,0.208 10 true Cylinder Head Cover Spacer

RH:

i.

Install the valve filter in the cylinder head cover.


ii.

Install a new gasket and the cylinder head cover spacer with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 11201 45.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

Hide 11202 46.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 15330B 47.INSTALL CAMSHAFT OIL CONTROL VALVE ASSEMBLY

a.
A161909

LH:

i.

Apply a light coat of engine oil to 2 new O-rings.


ii.

Install the 2 O-rings to the 2 oil control valves.


iii.

Install the 2 oil control valves with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.
A161910

RH:

i.

Apply a light coat of engine oil to 2 new O-rings.


ii.

Install the 2 O-rings to the 2 oil control valves.


iii.

Install the 2 oil control valves with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 15100R 48.INSTALL CRANKSHAFT POSITION SENSOR

A161908

a.

Install the crankshaft position sensor with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 19312 49.INSTALL CRANK POSITION SENSOR PROTECTOR

A161907

a.

Install the sensor protector with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11102A 50.INSTALL CAMSHAFT POSITION SENSOR

A161906

a.

Install the camshaft position sensor with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 51.INSTALL VVT SENSOR

a.
A161904

LH:

i.

Install the 2 VVT sensors with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.
A161905

RH:

i.

Install the 2 VVT sensors with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 19100P 52.INSTALL SPARK PLUG

Hide 12185 53.INSTALL OIL FILLER CAP HOUSING

a.
A161917

Align the protrusion of a new gasket with the cutout of the oil filler cap housing, and install the gasket to the housing.


b.
A161903

Install the cap housing with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12108 54.INSTALL OIL FILLER CAP SUB-ASSEMBLY

Hide 15671 56.INSTALL OIL FILTER BRACKET (w/o Oil Cooler)

Hide 15671 57.INSTALL OIL FILTER BRACKET (w/ Oil Cooler)

Hide 15781 58.INSTALL NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)