Home › Engine / Hybrid System › 3UR-FE LUBRICATION › OIL PUMP
RM27M0U _51 Engine / Hybrid System _049114 3UR-FE LUBRICATION _0234071 OIL PUMP A

3UR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 16322 1.INSTALL WATER INLET PIPE

a.

Apply soapy water to 2 new O-rings and install them to the water inlet pipe.


b.

Install the water inlet pipe to the No. 1 heat exchanger cover.


Hide 11302 2.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new oil pump gasket.


b.

Install the oil pump gasket to the cylinder block.


c.

Apply a light coat of engine oil to a new O-ring.


d.

Install the O-ring to the oil pan sub-assembly.


e.

Apply seal packing in a continuous line to the timing chain cover sub-assembly as shown in the following illustration.

A380092E01
1.292,2.448 1.344,2.521 1.344,2.521 1.51,2.521 true 3.854,2.49 4,2.49 4,2.49 4.073,2.427 true 0.646,4.667 0.75,4.865 0.104,0.198 10 false : 0.656,5.042 0.76,5.24 0.104,0.198 10 false : 0.656,5.438 0.76,5.635 0.104,0.198 10 false : 0.75,4.698 0.948,4.906 0.198,0.208 10 false *a 0.771,5.438 0.969,5.646 0.198,0.208 10 false *c 0.76,5.052 0.958,5.26 0.198,0.208 10 false *b 1.063,3.573 1.26,3.781 0.198,0.208 10 false E 4.021,3.552 4.219,3.76 0.198,0.208 10 false E 2.177,3.063 2.375,3.271 0.198,0.208 10 true E 0.938,1.833 1.083,2.031 0.146,0.198 10 true E 2.99,2.469 3.135,2.667 0.146,0.198 10 true E 0.667,2.865 0.802,3.042 0.135,0.177 10 false C 2.333,1.208 2.469,1.385 0.135,0.177 10 false A 2.917,1.208 3.052,1.385 0.135,0.177 10 false B 4.563,2.875 4.698,3.052 0.135,0.177 10 false D 2.01,2.385 2.156,2.583 0.146,0.198 10 true F 1.552,2.427 1.906,2.625 0.354,0.198 10 true B - B 3.479,2.406 3.833,2.604 0.354,0.198 10 true A - A 3.906,4.156 4.385,4.365 0.479,0.208 10 false 7.0 mm 5.469,4.156 5.948,4.365 0.479,0.208 10 false 7.0 mm 4.719,5.156 5.073,5.354 0.354,0.198 10 false A - A 6.135,5.188 6.49,5.385 0.354,0.198 10 false B - B 5.396,2.667 6.75,2.865 1.354,0.198 10 false F: 18.0 mm (0.709 in.) 5.385,2.375 6.771,2.563 1.385,0.188 10 false E: 16.0 mm (0.630 in.) 5.385,2.094 6.771,2.281 1.385,0.188 10 false D: 34.5 mm (1.36 in.) 5.385,1.802 6.719,2 1.333,0.198 10 false C: 35.0 mm (1.38 in.) 5.385,1.5 6.719,1.698 1.333,0.198 10 false B: 32.5 mm (1.28 in.) 5.385,1.198 6.719,1.396 1.333,0.198 10 false A: 27.5 mm (1.08 in.)

Text in Illustration
*a Continuous Line Area *b Dashed Line Area
*c Diagonal Line Area - -

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


A150825E11
1.771,1.219 2.406,0.833 2.406,0.833 2.667,0.833 true 2.708,1.74 2.927,1.906 0.219,0.167 10 false *b 2.75,0.75 3.302,0.917 0.552,0.167 10 false *c 0.156,1.646 0.875,1.813 0.719,0.167 10 false 2.0 (0.079) 0.167,1.323 0.875,1.49 0.708,0.167 10 false 3.2 (0.126) 0.167,0.604 0.875,0.771 0.708,0.167 10 false 6.0 (0.236) 1.052,1.75 1.281,1.917 0.229,0.167 10 false 8.0 0.167,1.135 0.896,1.302 0.729,0.167 10 false 4.0 (0.157) 2.115,1.75 2.417,1.906 0.302,0.156 10 false 12.0 1.604,1.75 1.917,1.927 0.313,0.177 10 false 10.0 1.615,2.917 1.813,3.083 0.198,0.167 10 false *b 0.927,2.521 1.135,2.688 0.208,0.167 10 false *a 0.958,1.948 1.438,2.125 0.479,0.177 10 false (0.315) 1.542,1.958 2.021,2.146 0.479,0.188 10 false (0.394) 2.083,1.958 2.573,2.135 0.49,0.177 10 false (0.472) 0.74,0.313 0.938,0.5 0.198,0.188 10 false *a

Apply Seal Packing As Follows:
Area Seal Packing Diameter Application Position from Inside Edge of Cover
Continuous Line Area 3.0 to 4.0 mm (0.118 to 0.157 in.) 2.5 mm (0.0984 in.)
Dashed Line Area 6.4 mm (0.252 in.) or more, or within OK area shown in illustration 7.0 mm (0.276 in.)
Diagonal Line Area 3.0 to 4.0 mm (0.118 to 0.157 in.) 5.5 mm (0.217 in.)



Text in Illustration
*a Seal Packing Thickness
*b Seal Packing Width
*c OK Area

NOTICE:
·

When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.

·

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installing.




f.
A162541

Align the oil pump drive rotor spline and crankshaft as shown in the illustration. Install the spline and timing chain cover sub-assembly to the crankshaft.


g.
U151511E02
2.813,0.771 2.958,0.948 0.146,0.177 10 false B 1.833,0.479 2.031,0.646 0.198,0.167 10 false *1 2.26,0.26 2.406,0.438 0.146,0.177 10 false A 1.781,2.083 1.927,2.26 0.146,0.177 10 true E 2.667,2.198 2.813,2.375 0.146,0.177 10 false F 2.948,1.896 3.094,2.073 0.146,0.177 10 false D 1.208,1.76 1.354,1.938 0.146,0.177 10 false C 2.542,2.76 2.688,2.938 0.146,0.177 10 false A 2.188,3.073 2.333,3.25 0.146,0.177 10 false A 1.771,3.125 1.917,3.302 0.146,0.177 10 false A 1.438,3.125 1.583,3.302 0.146,0.177 10 false A 1.021,3.052 1.167,3.229 0.146,0.177 10 false A 0.229,1.917 0.375,2.094 0.146,0.177 10 false A 0.167,1.01 0.313,1.188 0.146,0.177 10 false A 1.292,0.406 1.438,0.583 0.146,0.177 10 false A 1,0.302 1.146,0.479 0.146,0.177 10 false A 3.25,1.792 3.396,1.969 0.146,0.177 10 false A 3.156,1.01 3.302,1.188 0.146,0.177 10 false A 0.802,2.656 0.948,2.833 0.146,0.177 10 false B 0.74,2.375 0.885,2.552 0.146,0.177 10 false B 1.74,0.99 1.885,1.167 0.146,0.177 10 false B 2.594,2.438 2.74,2.615 0.146,0.177 10 false B 0.646,2.167 0.792,2.344 0.146,0.177 10 false D 2.24,1.469 2.385,1.646 0.146,0.177 10 false D 2.438,1.281 2.583,1.458 0.146,0.177 10 false D 0.927,1.302 1.073,1.479 0.146,0.177 10 true F 0.448,2.073 0.594,2.25 0.146,0.177 10 false F 1.406,0.625 1.552,0.802 0.146,0.177 10 false F 1.583,0.771 1.729,0.948 0.146,0.177 10 false F

Temporarily install the timing chain cover sub-assembly with the 28 bolts and nut.

Standard Bolt:
Item Length Thread Diameter
Bolt A 25 mm (0.984 in.) 8 mm (0.315 in.)
Bolt B 55 mm (2.17 in.) 8 mm (0.315 in.)
Bolt C 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt D 35 mm (1.38 in.) 10 mm (0.394 in.)
Bolt E 55 mm (2.17 in.) 10 mm (0.394 in.)
Bolt F 80 mm (3.15 in.) 10 mm (0.394 in.)


Text in Illustration
*1 Nut

NOTICE:

Make sure that there is no oil on the bolt threads.



h.
A174145E03
2.24,0.938 2.375,1.125 0.135,0.188 10 true 1 0.865,1.615 1.01,1.781 0.146,0.167 10 false 2 0.594,1.354 0.74,1.521 0.146,0.167 10 false 3

Tighten the 3 bolts in several steps in the sequence shown in the illustration.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


i.
A163330E04
2.375,1.99 2.5,2.156 0.125,0.167 10 false A 3.281,1.635 3.406,1.802 0.125,0.167 10 false B 0.521,0.146 0.646,0.313 0.125,0.167 10 true A 0.281,1.625 0.406,1.792 0.125,0.167 10 true A

Temporarily install the fan bracket assembly with the 4 bolts.

Standard Bolt:
Item Length Thread Diameter
Bolt A 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt B 80 mm (3.15 in.) 10 mm (0.394 in.)



j.

Temporarily install the V-ribbed belt tensioner assembly with the standard bolt and 6 mm hexagon wrench bolt.


k.
A174146E01
1.619,0.1 1.740,0.272 0.121,0.172 10 4 1.844,0.098 1.965,0.270 0.121,0.172 10 5 2.865,1.367 2.987,1.539 0.121,0.172 10 6 3.098,1.056 3.219,1.228 0.121,0.172 10 7 2.109,0 2.230,0.172 0.121,0.172 10 8 1.34,0 1.461,0.172 0.121,0.172 10 9 0.194,1.122 0.381,1.294 0.187,0.172 10 10 2.552,1.666 2.739,1.837 0.187,0.172 10 11

Tighten the 8 bolts labeled 4 to 11 in several steps in the sequence shown in the illustration.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


l.
A162544E04
0.552,1.844 0.75,2.021 0.198,0.177 10 true 12 1.74,0.729 1.938,0.906 0.198,0.177 10 false 13 2.531,2.729 2.729,2.906 0.198,0.177 10 false 19 2.594,2.448 2.792,2.625 0.198,0.177 10 false 18 2.479,2.135 2.677,2.313 0.198,0.177 10 false 17 1.479,2.052 1.677,2.229 0.198,0.177 10 true 16 1.406,0.969 1.604,1.146 0.198,0.177 10 false 15 2.01,1.75 2.208,1.927 0.198,0.177 10 true 14 0.615,2.146 0.813,2.323 0.198,0.177 10 false 20 0.177,1.01 0.375,1.188 0.198,0.177 10 false 28 0.25,1.917 0.448,2.094 0.198,0.177 10 false 27 2.135,3.083 2.333,3.26 0.198,0.177 10 false 26 1.729,3.104 1.927,3.281 0.198,0.177 10 false 25 0.719,2.688 0.917,2.865 0.198,0.177 10 false 22 0.969,3.063 1.167,3.24 0.198,0.177 10 false 24 1.396,3.104 1.594,3.281 0.198,0.177 10 false 23 0.688,2.396 0.885,2.573 0.198,0.177 10 false 21 0.958,0.25 1.156,0.427 0.198,0.177 10 false 30 1.24,0.406 1.438,0.583 0.198,0.177 10 false 29 2.896,1.958 3.094,2.135 0.198,0.177 10 false 34 2.219,0.208 2.417,0.385 0.198,0.177 10 false 33 1.917,0.458 2.115,0.635 0.198,0.177 10 false 32 2.542,1.615 2.74,1.792 0.198,0.177 10 true 31 3.052,0.99 3.25,1.167 0.198,0.177 10 false 35

Tighten the 23 bolts and nut labeled 12 to 35 in several steps in the sequence shown in the illustration.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

NOTICE:
A162545E01
0.846,1.634 0.983,1.823 0.137,0.188 10 A 1.309,0.348 0.931,1.621 false 0.931,1.621 2.17,0.366 false

After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration, wipe it off.



Hide 11202 3.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.

Install 5 new gaskets to the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.


b.

Install the gasket to the cylinder head cover sub-assembly LH.

NOTICE:

Remove any oil from the contact surface.



c.
A291560

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly LH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




d.
A162523E04
1.917,1.51 2.052,1.677 0.135,0.167 10 true A

Install the cylinder head cover sub-assembly LH washer with a new seal and the 14 bolts.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
except bolt A : 12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 11201 4.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

a.

Install 5 new gaskets to the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.


b.

Install the gasket to the cylinder head cover sub-assembly RH.

NOTICE:

Remove any oil from the contact surface.



c.
A291561

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly RH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




d.
A162525E04
1.427,1.5 1.563,1.667 0.135,0.167 10 true A

Install the cylinder head cover sub-assembly RH washer with a new seal and the 14 bolts.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
except bolt A : 12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 19500 5.INSTALL IGNITION COIL ASSEMBLY

a.

Install the 8 ignition coils with the 8 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13471 6.INSTALL CRANKSHAFT PULLEY

a.
A164230E07
0.179,0.536 0.363,0.707 0.184,0.172 10 *a 0.626,1.593 0.820,1.756 0.194,0.163 10 *b 2.365,1.739 2.716,1.909 0.350,0.170 10 SST 2.032,1.354 2.322,1.813 false 2.322,1.813 1.814,1.466 false

Align the crankshaft pulley set key with the key groove of the crankshaft pulley, and slide on the crankshaft pulley.

Text in Illustration
*a Hold
*b Turn
*c SST


b.

Using SST, install the crankshaft pulley set bolt.

SST
09213-70011  
09330-00021  

Torque:
300 N*m (3059 kgf*cm, 221 ft.*lbf)


Hide 7.CONNECT WIRE HARNESS CLAMP BRACKET

a.

Connect the wire harness clamp bracket to the timing chain cover sub-assembly with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 16603 8.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.

Install the No. 1 idler pulley sub-assembly with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16173 9.INSTALL WATER PUMP PULLEY

a.

Temporarily install the water pump pulley with the 4 bolts.


b.

Using SST, hold the water pump pulley and tighten the 4 bolts.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16323 10.INSTALL WATER INLET HOUSING

a.
A162555E05
0.493,0.13 0.681,0.305 0.188,0.174 10 *1 0.729,0.228 0.789,0.228 false 0.789,0.228 1.21,0.79 false

Install a new gasket to the timing chain cover sub-assembly.

Text in Illustration
*1 Gasket


b.

Install the water inlet housing with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17303 11.INSTALL AIR TUBE SUB-ASSEMBLY

a.

Connect the 2 hoses.


b.

Install the air tube sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16355 14.INSTALL FRONT WATER BY-PASS JOINT

a.

Install 2 new gaskets and the front water by-pass joint with the 4 nuts to the cylinder head.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the No. 2 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.


Hide 16293 15.CONNECT NO. 10 WATER BY-PASS HOSE

a.
A291559E05
2.177,0.083 2.292,0.083 2.292,0.083 2.417,0.448 true 1.146,0.729 1.313,0.729 1.313,0.729 1.823,1.135 true 1.042,2.063 1.208,2.063 1.208,2.063 1.375,1.865 true 2.042,2.083 1.875,2.083 1.875,2.083 1.708,1.885 true 0.958,0.656 1.135,0.854 0.177,0.198 10 true *1 1.969,0 2.156,0.198 0.188,0.198 10 false *2 0.813,1.969 0.99,2.125 0.177,0.156 10 true *a 2.073,1.99 2.26,2.135 0.188,0.146 10 true *b

Connect the No. 10 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.

Text in Illustration
*1 No. 9 Water By-pass Hose
*2 No. 10 Water By-pass Hose
*a Paint Mark (Orange)
*b Paint Mark (Yellow)


Hide 16297 16.CONNECT NO. 9 WATER BY-PASS HOSE

a.

Connect the No. 9 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.


Hide 16206 17.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Connect the No. 2 water by-pass hose and No. 3 water by-pass hose to the water by-pass pipe sub-assembly, and slide the 2 clamps to secure the hoses.


b.

Install the water by-pass pipe sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the air tube sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16261G 18.INSTALL NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose to the inlet water housing and front water by-pass joint, and slide the 2 clamps to secure the hoses.


Hide 27020 19.INSTALL GENERATOR ASSEMBLY

a.

Install the 2 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the generator assembly with the 2 bolts and 2 nuts.

Torque:
43 N*m (439 kgf*cm, 32 ft.*lbf)


c.

Connect the generator connector.


d.

Connect the generator assembly wire with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


e.

Install the terminal cap.


f.

Connect the wire harness bracket to the generator assembly with the bolt.

Torque:
31 N*m (316 kgf*cm, 23 ft.*lbf)


Hide 44320 20.CONNECT VANE PUMP ASSEMBLY

A163333E10
1.667,1.854 1.49,1.854 1.49,1.854 0.896,1.635 true 1.708,1.771 1.885,1.948 0.177,0.177 10 true *a

HINT:

Before performing the following procedures, move the spacer until the vane pump assembly can be installed.

Text in Illustration
*a Spacer


a.

Connect the vane pump assembly to the timing chain cover sub-assembly with the 2 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 11452 21.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 22.INSTALL OIL FILTER BRACKET (w/o Oil Cooler)

a.

Apply a light coat of engine oil to 2 new O-rings.


b.

Install the 2 O-rings to the timing chain cover sub-assembly.


c.

Install the oil filter bracket with the 2 bolts and 2 nuts.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 15671 23.INSTALL OIL FILTER BRACKET (w/ Oil Cooler)

Hide 15781 24.INSTALL NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)

Hide 16268A 25.INSTALL NO. 2 WATER BY-PASS PIPE (w/ Oil Cooler)

a.

Connect the 4 hoses to the No. 2 water by-pass pipe, and slide the 4 clamps to secure the hoses.


b.

Install the No. 2 water by-pass pipe with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 83520 26.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY

Hide 23902 28.CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY

a.

Connect the No. 2 fuel tube sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 88320 29.CONNECT COOLER COMPRESSOR ASSEMBLY

a.
A163332E01
2.93,1.786 3.058,1.951 0.128,0.165 10 2 3.071,1.054 3.199,1.219 0.128,0.165 10 3 2.779,1.349 2.907,1.514 0.128,0.165 10 1 2.254,1.782 2.382,1.947 0.128,0.165 10 4

Install the cooler compressor assembly with the 2 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the 2 bolts and 2 nuts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)

NOTICE:

Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor assembly.



Hide 30.CONNECT HEATER HOSE AND PIPE

a.

Connect the 3 hoses, and slide the 3 clamps to secure the hoses.


b.

Install the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 31.CONNECT AIR PUMP HOSE AND WIRE HARNESS

a.

Connect the No. 2 air hose and No. 3 air hose to the air tube sub-assembly, and slide the 2 clamps to secure the hoses.


b.

Connect the 2 clamps and air pump wire harness.


Hide 17111 32.INSTALL INTAKE MANIFOLD

Hide 33.CONNECT ENGINE WIRE

a.

Engine Room RH Side:

i.

Connect the 7 clamps.


ii.

Connect the throttle position sensor and throttle control motor connector.


iii.

Connect the 2 air pump connectors.


iv.

Install the ground wire RH with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


v.

Connect the 2 VVT sensor connectors.


vi.

Connect the injector connector.


vii.

Connect the 4 ignition coil connectors.


viii.

Connect the 2 camshaft timing oil control valve connectors.


ix.
A162564

Connect the 2 clamps and power steering oil pressure switch connector.


x.

for 4WD:

Connect the clamp and junction connector.



b.

Engine Room LH Side:

i.

Connect the cooler compressor connector.


ii.

Connect the 3 clamps.


iii.

Connect the camshaft position sensor connector.


iv.

Connect the 2 camshaft timing oil control valve connectors.


v.

Connect the engine coolant temperature sensor connector.


vi.

Connect the 5 clamps.


vii.

Install the ground wire LH with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


viii.

Connect the 2 VVT sensor connectors.


ix.

Connect the 4 ignition coil connectors.


x.

Connect the injector connector.


xi.

Connect the 2 wire harness clamps.


xii.

Connect the 4 air injection control driver connectors.


xiii.

Connect the 2 connectors and attach the 2 clamps to the engine room junction block.


xiv.

Install the engine room relay block cover.



Hide 16400 36.INSTALL RADIATOR ASSEMBLY

Hide 39.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL