| ● | Non-reusable part | - | - |
| *A | for 2-piece Type | *B | for 1-piece Type |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the windshield glass removal/installation are shown below.
When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the front camera system, pre-collision system, dynamic radar cruise control system, lane tracing assist system, road sign assist system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.
1.REMOVE WINDSHIELD WIPER MOTOR AND LINK
8646C
2.REMOVE FORWARD RECOGNITION CAMERA
86401
3.REMOVE FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY
87810
4.REMOVE INNER REAR VIEW MIRROR ASSEMBLY
62311B
5.SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
62312B
6.SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Use the same procedure as for the RH side.
62212
8.REMOVE FRONT PILLAR GARNISH LH
Use the same procedure as for the RH side.
74310
10.REMOVE VISOR ASSEMBLY RH
74320
11.REMOVE VISOR ASSEMBLY LH
Use the same procedure as for the RH side.
74348B
12.REMOVE VISOR HOLDER RH
74348C
13.REMOVE VISOR HOLDER LH
Use the same procedure as for the RH side.
63310
16.SEPARATE ROOF HEADLINING ASSEMBLY
Slightly lower the front section of the roof headlining so that the windshield glass can be removed.
Do not damage the roof headlining or vehicle interior.
56111
17.REMOVE WINDSHIELD GLASS
|
|
| *a | When using a new Windshield Glass | *b | When reusing the Windshield Glass |
| *c | Matchmark | - | - |
Apply protective tape to the area around the installation position of the windshield glass sub-assembly on the vehicle body to prevent it from being scratched as shown in the illustration.
When reusing the windshield glass, place matchmarks on the windshield glass sub-assembly and vehicle body at the locations indicated in the illustration.
| *a | Suction Cup | - | - |
Install the suction cups to the windshield glass sub-assembly.
| *1 | Windshield Glass Stopper | - | - |
| *a | Piano Wire | - | - |
Cut the adhesive by the below procedure.
1. Pass a piano wire between the vehicle body and windshield glass sub-assembly from the interior.
2. Tie both wire ends to wooden blocks or similar objects that can serve as handles.
3. Cut the adhesive by pulling the piano wire around the windshield glass sub-assembly.
When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.
To prevent the safety pad from being scratched when removing the windshield glass sub-assembly, place a plastic sheet between the piano wire and safety pad.
Be careful not to damage the front window inner center moulding.
| *A | for 1-piece Type | *B | for 2-piece Type |
| *1 | No. 1 Windshield Glass Stopper | *2 | No. 2 Windshield Glass Stopper |
Using suction cups, disengage the windshield glass stoppers to remove the windshield glass sub-assembly.
Be careful not to drop the windshield glass sub-assembly.
Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.
75533G
18.REMOVE WINDSHIELD OUTSIDE MOULDING
When reusing the windshield glass sub-assembly:
| *a | Back Side of Windshield Glass Sub-assembly | - | - |
Using a scraper, remove the windshield outside moulding.
Be careful not to damage the windshield glass sub-assembly.
Be sure to replace the windshield outside moulding with a new one.
56117A
19.REMOVE WINDOW GLASS ADHESIVE DAM
When reusing the windshield glass sub-assembly:
| *a | Back Side of Windshield Glass Sub-assembly | - | - |
Using a scraper, remove the window glass adhesive dam.
Be careful not to damage the windshield glass sub-assembly.
Be sure to replace the window glass adhesive dam with a new one.
56115A
20.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)
When reusing the windshield glass sub-assembly:
| *a | Back Side of Windshield Glass Sub-assembly | - | - |
Using a scraper, remove the 2 No. 1 windshield glass stoppers.
Be careful not to damage the windshield glass sub-assembly.
Be sure to replace the No. 1 windshield glass stoppers with new ones.
56116C
21.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
When reusing the windshield glass sub-assembly:
| *a | Back Side of Windshield Glass Sub-assembly | - | - |
Using a scraper, remove the 2 No. 2 windshield glass stoppers.
Be careful not to damage the windshield glass sub-assembly.
Be sure to replace the No. 2 windshield glass stoppers with new ones.
56115A
22.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Remove the 2 No. 1 windshield glass stoppers.
Be sure to replace the No. 1 windshield glass stoppers with new ones.