|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | ★ | Precoated part |
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1.INSTALL CAMSHAFT
|
|
| *1 | No. 1 Valve Rocker Arm Sub-assembly | *2 | Valve Lash Adjuster Assembly |
| *3 | Valve Stem Cap | - | - |
| *a | "0" Timing Mark | *b | Timing Mark |
Turn the crankshaft clockwise to align the timing mark (cutout) on the crankshaft pulley with the "0" timing mark on the No. 2 timing chain cover assembly.
Check that the No. 1 valve rocker arm sub-assembly is correctly installed as shown in the illustration.
Clean the camshaft housing sub-assembly and the cams and journals of the intake camshaft sub-assembly and exhaust camshaft sub-assembly, and then apply engine oil to them.
Apply a light coat of engine oil to the journals of the exhaust camshaft sub-assembly and install the exhaust camshaft sub-assembly to the camshaft housing sub-assembly.
Apply a light coat of engine oil to the journals of the intake camshaft sub-assembly and install the intake camshaft sub-assembly to the camshaft housing sub-assembly.
2.INSTALL CAMSHAFT BEARING CAP
| *1 | No. 1 Camshaft Bearing Cap | *2 | No. 2 Camshaft Bearing Cap |
| *3 | No. 3 Camshaft Bearing Cap | *4 | No. 4 Camshaft Bearing Cap |
Set the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap as shown in the illustration.
Uniformly tighten the 11 camshaft bearing cap bolts in the order shown in the illustration.
Uniformly tighten the 7 camshaft bearing cap bolts in the order shown in the illustration.
3.TEMPORARILY TIGHTEN CAMSHAFT TIMING GEAR
| *a | Paint Mark | *b | Timing Mark |
| *c | Knock Pin | - | - |
Set the camshaft timing gear assembly and camshaft timing exhaust gear assembly to the timing chain sub-assembly in order as shown in the illustration.
Align the timing mark on the camshaft timing gear assembly with the paint mark on the timing chain sub-assembly.
Align the timing mark on the camshaft timing exhaust gear assembly with the paint mark on the timing chain sub-assembly.
Using the hexagonal portion of the intake camshaft sub-assembly, install the camshaft timing gear assembly to the intake camshaft sub-assembly.
Check that the knock pin matches the pin hole from the No. 2 timing chain cover sub-assembly side.
Using a bi-hexagon socket wrench (10 mm), temporarily install the camshaft timing gear assembly with the bolt.
Temporarily install the bolt enough that the camshaft timing gear assembly does not detach from the knock pin of the intake camshaft sub-assembly.
Using the hexagonal portion of the exhaust camshaft sub-assembly, install the camshaft timing exhaust gear assembly to the exhaust camshaft sub-assembly.
Temporarily install with the 2 bolts.
The 2 bolts can only be installed as shown in the illustration if the knock pin on the exhaust camshaft sub-assembly and the pin hole on the camshaft timing exhaust gear assembly match. If the 2 bolts cannot be installed, the knock pin and pin hole do not match.
13506
4.INSPECT CHAIN SUB-ASSEMBLY
| *1 | No. 1 Chain Vibration Damper | *2 | Chain Tensioner Slipper |
Check the status of the camshaft timing gear assembly and camshaft timing exhaust gear assembly temporarily installed to each camshaft.
Camshaft timing gear assembly side:
Check that the timing chain sub-assembly does not overlap the No. 1 chain vibration damper as shown in the illustration.
If the timing chain sub-assembly overlaps the No. 1 chain vibration damper, install it again.
Camshaft timing exhaust gear assembly side:
Check that the timing chain sub-assembly does not overlap the chain tensioner slipper as shown in the illustration.
5.TIGHTEN CAMSHAFT TIMING GEAR
| *a | Hold | *b | Paint Mark |
| *c | Timing Mark | - | - |
Using the hexagonal portion of the intake camshaft sub-assembly, hold the intake camshaft sub-assembly.
Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.
Do not disassemble the camshaft timing gear assembly.
Using a bi-hexagon socket wrench (10 mm), tighten the bolt on the camshaft timing gear assembly.
Using the hexagonal portion of the exhaust camshaft sub-assembly, hold the exhaust camshaft sub-assembly.
Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.
Do not disassemble the camshaft timing gear assembly.
Using a hexagon wrench (5 mm), tighten the 2 bolts.
Check that the paint marks and timing marks are positioned as shown in the illustration.
| *a | Hold | - | - |
|
Turn | - | - |
Using the hexagonal portion of the intake camshaft sub-assembly, check that the timing chain sub-assembly slackens when the intake camshaft sub-assembly is moved in the direction shown in the illustration.
If the timing chain sub-assembly remains tight and does not slacken, the chain tensioner slipper and No. 1 chain vibration damper may overlap the timing chain sub -assembly, so install them again.
Remove the pin from the No. 1 chain tensioner assembly.
11102A
9.INSTALL CAMSHAFT POSITION SENSOR
135A0
12.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)
82121
15.CONNECT ENGINE WIRE
12262
16.INSTALL NO. 2 VENTILATION HOSE
17.INSTALL CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL