Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › CAMSHAFT › 2020.08–2021.07
RM3700E _51 Engine / Hybrid System _093331 M15A-FXE ENGINE MECHANICAL _0440544 CAMSHAFT A

M15A-FXE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A475102N01
6.385,0.313 6.719,0.313 false 5.396,2.979 5.729,2.979 false 5.75,3.615 6.083,3.615 false 3.854,3.271 4.188,3.271 false 3.573,3.448 3.823,3.448 false 4.083,1.823 4.344,1.823 false 4.26,1.302 4.594,1.302 false 3.354,1.01 3.573,1.01 false 2.281,1 2.531,1 false 4.219,0.813 4.552,0.813 false 3.76,0.625 4.094,0.625 false 1.635,2.5 1.74,2.333 1.74,2.333 1.865,2.333 false 1.729,3.844 1.729,4.031 false 1.531,3.156 1.865,3.156 false 0.906,3.094 0.906,3.229 false 1.125,2.521 1.208,2.188 1.208,2.188 1.375,2.188 false 3.979,2.26 4.813,2.26 false 2.427,2.875 2.594,2.875 2.594,2.875 2.677,2.708 false 6.167,0.188 6.448,0.542 0.281,0.354 18 false 1 4.896,1.177 5.177,1.531 0.281,0.354 18 false 5 4.823,1.667 5.458,1.979 0.635,0.313 18 false 11 5.135,2.135 5.771,2.458 0.635,0.323 18 false 10 3.188,0.885 3.521,1.208 0.333,0.323 18 false 6 2.104,0.865 2.438,1.188 0.333,0.323 18 false 4 2.146,2.229 2.479,2.552 0.333,0.323 18 false 7 0.875,3.219 1.208,3.542 0.333,0.323 18 false 9 1.802,3.969 2.135,4.292 0.333,0.323 18 false 8 6.135,3.479 6.469,3.802 0.333,0.323 18 false 3 5.792,2.844 6.125,3.167 0.333,0.323 18 false 2 4.615,0.74 5.031,0.906 0.417,0.167 10 false ● ★ 4.146,0.552 4.563,0.719 0.417,0.167 10 false ● ★ 2.729,0.396 3.146,0.563 0.417,0.167 10 false x3 2.615,1.375 3.031,1.542 0.417,0.167 10 false x3 2.594,1.771 3.01,1.938 0.417,0.167 10 false x11 1.208,2.448 1.625,2.615 0.417,0.167 10 false x2 0.344,2.635 0.76,2.802 0.417,0.167 10 false x3 4.771,4.021 5.188,4.188 0.417,0.167 10 false x4 4.25,3.198 4.667,3.365 0.417,0.167 10 false ● 3.885,3.375 4.302,3.542 0.417,0.167 10 false ● 3.646,1.5 4.063,1.667 0.417,0.167 10 false x2 1.927,3.083 2.344,3.25 0.417,0.167 10 false ● 1.417,2.104 1.833,2.271 0.417,0.167 10 false ● ★ 4.646,1.74 5.063,1.906 0.417,0.167 10 false ● 3.594,3.49 4.01,3.656 0.417,0.167 10 false x4 4.083,1.896 4.5,2.063 0.417,0.167 10 false x3 2.25,2.802 2.667,2.969 0.417,0.167 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
2 NO. 2 VENTILATION HOSE 12262 - - -
3 ENGINE WIRE 82121 - - -
4 IGNITION COIL ASSEMBLY 19500 (Click here) - -
5 CAMSHAFT POSITION SENSOR (for Intake Side) 11102A (Click here) - -
6 CAMSHAFT POSITION SENSOR (for Exhaust Side) 11102A (Click here) - -
7 CAM TIMING OIL CONTROL SOLENOID ASSEMBLY 15370 (Click here) - -
8 CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY) 135A0B (Click here) - -
9 CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY 13090D (Click here) - -
10 CYLINDER HEAD COVER SUB-ASSEMBLY 11201 (Click here) - -
11 SPARK PLUG TUBE GASKET 11193 (Click here) - -

● Non-reusable part ★ Precoated part

A462200N01
6.552,0.188 6.885,0.188 false 4.292,2.792 4.625,2.792 false 3.177,2.938 3.51,2.938 false 1.396,4.417 1.625,4.417 false 2.385,2.604 2.385,2.802 false 1.604,2.813 1.604,3 false 3,1.271 3,2.354 3,2.354 5.833,2.354 false 3.688,1.469 3.688,2.354 false 4.417,1.802 4.417,2.354 false 5.208,2.031 5.208,2.354 false 6.24,0.063 6.792,0.417 0.552,0.354 18 false 12 6.167,2.208 6.719,2.563 0.552,0.354 18 false 15 4.688,2.667 5.24,3.021 0.552,0.354 18 false 17 2.875,2.813 3.427,3.167 0.552,0.354 18 false 16 1.865,4.281 2.417,4.635 0.552,0.354 18 false 13 1.5,2.99 2.052,3.344 0.552,0.354 18 false 14 2.281,2.792 2.833,3.146 0.552,0.354 18 false 14 1.729,1.969 2.042,2.167 0.313,0.198 10 false x2 3.635,0.5 3.948,0.698 0.313,0.198 10 false x11 3.208,0.625 3.521,0.823 0.313,0.198 10 false x7

Procedure Part Name Code
Z101186

Z101188

Z101187

12 SET NO. 1 CYLINDER TO TDC (COMPRESSION) - (Click here) - -
13 STRAIGHT SCREW PLUG - (Click here) - -
14 CAMSHAFT TIMING GEAR ASSEMBLY 13050 (Click here) - -
15 CAMSHAFT BEARING CAP - (Click here) - -
16 INTAKE CAMSHAFT SUB-ASSEMBLY 13501A - - -
17 EXHAUST CAMSHAFT SUB-ASSEMBLY 13502B - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during camshaft removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Reconnected to auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.REMOVE CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 12262 2.DISCONNECT NO. 2 VENTILATION HOSE

a.
A461027


Hide 82121 3.REMOVE ENGINE WIRE

a.
A461025


Hide 19500 4.REMOVE IGNITION COIL ASSEMBLY

Z101186

Click here(Click here)

Hide 11102A 5.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Z101186

Click here(Click here)

Hide 11102A 6.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Z101186

Click here(Click here)

Hide 15370 7.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Z101186

Click here(Click here)

Hide 135A0B 8.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (EXHAUST CAMSHAFT TIMING GEAR BOLT ASSEMBLY)

Z101186

Click here(Click here)

Hide 13090D 9.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Z101186

Click here(Click here)

Hide 11201 10.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Z101186

Click here(Click here)

Hide 11193 11.REMOVE SPARK PLUG TUBE GASKET

Z101186

Click here(Click here)

Hide 12.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.
A462189C01
0.729,1.135 1.146,0.719 true 1.479,1.177 1.24,0.813 true 1.229,0.563 1.135,0.375 true 2.396,0.667 2.75,1.052 true 2.344,0.531 2.646,0.292 true 5.042,0.167 5.417,0.167 true 5.104,0.385 4.781,0.24 4.781,0.24 4.635,0.24 true 0.594,1.177 0.802,1.365 0.208,0.188 10 true *a 2.771,1.031 2.979,1.219 0.208,0.188 10 true *a 2.667,0.208 2.875,0.396 0.208,0.188 10 true *b 0.969,0.135 1.177,0.323 0.208,0.188 10 true *b 1.469,1.198 1.677,1.385 0.208,0.188 10 true *b 4.375,0.167 4.583,0.354 0.208,0.188 10 true *b 5.438,0.083 5.646,0.271 0.208,0.188 10 true *c 3.979,0.042 4.115,0.333 0.135,0.292 18 true i 0.375,0.063 0.844,0.333 0.469,0.271 18 true ii, iii
*a Paint Mark *b Timing Mark
*c "0" Timing Mark - -


i.

Turn the crankshaft clockwise to align the timing mark (cutout) on the crankshaft pulley with the "0" timing mark on the No. 2 timing chain cover assembly.


ii.

Check that the timing marks are positioned as shown in the illustration.

HINT:

If the timing marks are not positioned as shown in the illustration, turn the crankshaft clockwise and then align them again.



iii.

Place paint marks on the timing chain sub-assembly at points aligned with the timing marks on the camshaft timing gear assembly and camshaft timing exhaust gear assembly.



Hide 13.REMOVE STRAIGHT SCREW PLUG

Z101186

Click here(Click here)

Hide 13050 14.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A475441C01
1.438,2.521 1.708,2.521 true 4.906,2.938 5.052,3.302 true 1.479,0 1.677,0.167 0.198,0.167 10 true *a 5.094,0 5.292,0.167 0.198,0.167 10 true *a 1.229,2.427 1.427,2.594 0.198,0.167 10 true *b 5.042,3.333 5.24,3.5 0.198,0.167 10 true *c 2.948,4.115 3.146,4.281 0.198,0.167 10 true *d 5.906,4.24 6.104,4.406 0.198,0.167 10 true *d 0.427,0.073 0.604,0.385 0.177,0.313 18 true i 4.021,0.063 4.198,0.375 0.177,0.313 18 true ii 0.438,2.073 0.656,2.375 0.219,0.302 18 true iii 2.417,4.156 2.656,4.427 0.24,0.271 18 true iv 0.688,4.26 0.865,4.531 0.177,0.271 18 true v 5.448,4.271 5.646,4.542 0.198,0.271 18 true vi 4.396,4.719 4.656,4.99 0.26,0.271 18 true vii
*a Approximately 15° *b Pin
*c Pin Hole (No. 1 Chain Tensioner Assembly Side) *d Hold
V113147

Turn - -


i.

Rotate the crankshaft approximately 15° clockwise.


ii.

Rotate the crankshaft approximately 15° counterclockwise.


iii.

Insert the pin to the No. 1 chain tensioner assembly pin hole.


iv.

Using the hexagonal portion of the exhaust camshaft sub-assembly, secure the exhaust camshaft sub-assembly.

NOTICE:

Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.



v.

Remove the 2 bolts from the camshaft timing exhaust gear assembly.


vi.

Using the hexagonal portion of the intake camshaft sub-assembly, secure the intake camshaft sub-assembly.

NOTICE:
·

Do not damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube.

·

Do not disassemble the camshaft timing gear assembly.




vii.

Using a bi-hexagon socket wrench (10 mm), remove the bolt from the camshaft timing gear assembly.



b.
A475442C02
2.667,3.115 2.979,2.823 true 2.75,4.323 2.99,4.552 true 2.271,3.677 2.542,3.677 true 5.208,0.25 5.406,0.427 0.198,0.177 10 true *a 3.042,2.729 3.24,2.906 0.198,0.177 10 true *1 3.052,4.51 3.25,4.688 0.198,0.177 10 true *2 2.052,3.594 2.25,3.771 0.198,0.177 10 true *3 0.542,0.146 0.719,0.458 0.177,0.313 18 true i 0.615,2.813 0.792,3.125 0.177,0.313 18 true ii 3.698,2.771 4.417,3.083 0.719,0.313 18 false iii, iv
*1 Camshaft Timing Gear Assembly *2 Camshaft Timing Exhaust Gear Assembly
*3 Timing Chain Sub-assembly - -
*a Hold - -
V113147

Turn
V113148

Remove in this Direction


i.

Using the hexagonal portion of the exhaust camshaft sub-assembly, loosen and hold the timing chain sub-assembly while moving the exhaust camshaft sub-assembly in the direction shown in the illustration.


ii.

Move the camshaft timing gear assembly together with the camshaft timing exhaust gear assembly and timing chain sub-assembly toward the No. 2 timing chain cover assembly as shown in the illustration.


iii.

Remove the camshaft timing exhaust gear assembly from the timing chain sub-assembly.


iv.

Remove the camshaft timing gear assembly from the timing chain sub-assembly.



Hide 15.REMOVE CAMSHAFT BEARING CAP

a.
A462185C01
0.781,2.604 1.052,2.604 true 1.469,2.625 1.625,2.625 true 1.854,2.74 1.854,2.625 1.854,2.625 2.073,2.583 true 2.375,2.573 2.5,2.573 true 4.833,1.281 4.99,1.479 0.156,0.198 10 true 1 6.375,0.708 6.531,0.906 0.156,0.198 10 true 2 6.302,1.573 6.458,1.771 0.156,0.198 10 true 3 5.333,0.406 5.49,0.604 0.156,0.198 10 true 4 5.302,1.281 5.458,1.479 0.156,0.198 10 true 5 5.906,0.406 6.063,0.604 0.156,0.198 10 true 6 5.792,1.292 5.948,1.49 0.156,0.198 10 true 7 1.385,1.958 1.542,2.156 0.156,0.198 10 true 1 1.406,3.552 1.563,3.75 0.156,0.198 10 true 2 1.375,3.021 1.531,3.219 0.156,0.198 10 true 3 3.146,2.26 3.302,2.458 0.156,0.198 10 true 4 3.115,2.74 3.271,2.938 0.156,0.198 10 true 5 2.76,2.01 2.917,2.208 0.156,0.198 10 true 6 2.781,3.063 2.938,3.26 0.156,0.198 10 true 7 2.365,2.01 2.521,2.208 0.156,0.198 10 true 8 2.354,3.531 2.51,3.729 0.156,0.198 10 true 9 1.896,2.042 2.104,2.24 0.208,0.198 10 true 10 1.844,3.521 2.073,3.708 0.229,0.188 10 true 11 0.573,2.521 0.771,2.729 0.198,0.208 10 true *1 1.271,2.542 1.469,2.75 0.198,0.208 10 true *2 1.771,2.771 1.979,2.979 0.208,0.208 10 true *3 2.188,2.5 2.385,2.719 0.198,0.219 10 true *4 0.469,0.094 0.698,0.385 0.229,0.292 18 true i 3.958,0.115 4.188,0.406 0.229,0.292 18 true ii 0.51,2.01 0.74,2.302 0.229,0.292 18 true iii
*1 No. 1 Camshaft Bearing Cap *2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap *4 No. 4 Camshaft Bearing Cap


i.

Secure the timing chain sub-assembly to the vehicle using rope, etc.

NOTICE:

Do not drop the timing chain sub-assembly into the timing chain cover assembly.



ii.

Uniformly loosen and remove the 7 camshaft bearing cap bolts in the order shown in the illustration.


iii.

Uniformly loosen and remove the 11 camshaft bearing cap bolts in the order shown in the illustration.

NOTICE:

Uniformly loosen the camshaft bearing cap bolts while holding the camshaft horizontally.


1. Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, No. 3 camshaft bearing cap and No. 4 camshaft bearing cap.

HINT:

Arrange the removed parts so that they can be reinstalled in their original locations.




Hide 13501A 16.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY

a.
A462186


Hide 13502B 17.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY

a.
A462187