MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU monitors the high-voltage wiring between the HV battery and hybrid motor control inverter assembly and detects an open circuit malfunction.
This DTC is differentiated from P300449 based on detection timing (after ignition switch is turned to ON (READY)). If P300449 is also output at the same time, first perform troubleshooting for P300449.
If there is a SMRG stuck open malfunction, only P1C8449 is output.
The cause of this malfunction may be one of the following:
Voltage sensor (VH or VL) malfunction
Motor generator control ECU (MG ECU) malfunction
Communication (wire harness) malfunction
HV battery malfunction
No. 1 traction battery device box assembly malfunction
Hybrid motor control inverter assembly malfunction
High-voltage wire harness malfunction
High-voltage connector or connection malfunction
Hybrid vehicle control ECU malfunction
No. 1 traction battery device box assembly malfunction
Low voltage wire harness malfunction
Low voltage connector malfunction
Refer to the description for DTC P0AE411.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE411
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate | DTC Output from | Priority |
|---|---|---|---|---|---|---|---|
| P1C8449 | High Voltage Power Resource Circuit Short during Ready ON | High-voltage circuit malfunctions between the HV battery and hybrid motor control inverter assembly.
When the ignition switch is ON (READY), both "VL-Voltage before Boosting" and "VH-Voltage after Boosting" drop abnormally. The EV electric battery fuse is blown, the service plug grip is removed, SMRB or SMRG remains open, or the high-voltage cable has an open circuit. (1 trip detection logic) |
·
No. 1 traction battery device box assembly ·
Wire harness or connector ·
Hybrid vehicle control ECU |
Comes on | Master Warning: Comes on | Hybrid Control | A |
| DTC No. | Data List |
|---|---|
| P1C8449 | ·
Hybrid/EV Battery Voltage ·
Hybrid/EV Battery Current ·
VL-Voltage before Boosting ·
VH-Voltage after Boosting |
The following items can be helpful when performing repairs:
Ready Signal
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON (READY) and wait for 3 minutes or more.
According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes. If the difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V, the vehicle has returned to normal.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE, perform driving pattern again.
Refer to the wiring diagram for the HV Battery High-voltage Line Circuit.
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*
*: for AWD
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the hybrid motor control inverter assembly and rear hybrid motor control inverter assembly*.
*: for AWD
After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P1C8449 and Microcomputer malfunction of Hybrid control system DTCs in the table below are output | A |
| P1C8449 and Microcomputer malfunction of Motor generator control system DTCs in the table below are output | B |
| P1C8449 and Power source circuit malfunction of Motor generator control system DTCs in the table below are output | C |
| P1C8449 and Communication system malfunction of Hybrid control system DTCs in the table below are output | D |
| P1C8449 and System malfunction of Hybrid control system DTCs in the table below are output | E |
| P1C8449 and System malfunction of Motor generator control system DTCs in the table below are output | F |
| P0A9563 and DTCs other than the DTCs in the table below are output | G |
| P1C8449 and P0A9563 are output | H |
| Only P1C8449 is output | I |
| Malfunction Content | System | Relevant DTC | |
|---|---|---|---|
| Microcomputer malfunction | Hybrid control system | P0A1B49 | Drive Motor "A" Control Module Internal Electronic Failure |
| P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure | ||
| Motor generator control system | P0A1B1F | Generator Control Module Circuit Intermittent | |
| P0A1A47 | Generator Control Module Watchdog / Safety MC Failure | ||
| P0A1A49 | Generator Control Module Internal Electronic Failure | ||
| P1C2A1C | Generator A/D Converter Circuit Circuit Voltage Out of Range | ||
| P1C2A49 | Generator A/D Converter Circuit Internal Electronic Failure | ||
| P313383 | Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect | ||
| P313386 | Communication Error from Generator to Drive Motor "A" Signal Invalid | ||
| P313387 | Communication Error from Generator to Drive Motor "A" Missing Message | ||
| Power source circuit malfunction | Motor generator control system | P06D61C | Generator Control Module Offset Power Circuit Voltage Out of Range |
| Communication system malfunction | Hybrid control system | P312387 | Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message |
| System malfunction | Hybrid control system | P0C7600 | Hybrid/EV Battery System Discharge Time Too Long |
| P0D2D1C | Drive Motor "A" Inverter Voltage Sensor Voltage Out of Range | ||
| P1C8349 | High Voltage Power Resource Circuit Voltage Sensor after Boosting Malfunction | ||
| P0E311C | Boosting Converter Voltage Sensor "A" Voltage Out of Range | ||
| Motor generator control system | P0D2D16 | Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Below Threshold | |
| P0D2D17 | Drive Motor "A" Inverter Voltage Sensor(VH) Circuit Voltage Above Threshold | ||
| P1CB69E | Drive Motor "A" Inverter Voltage Sensor(VH) Stuck On | ||
| P0CA300 | DC/DC Converter Step Up Voltage Performance | ||
P1C8449 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Post-procedure1
Turn the ignition switch off.
A
B
C
D
E
F
G
H
I
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
With the vehicle stopped, apply the parking brake and turn the ignition switch to ON (READY).
Perform this test with the AUTO function (shift-linked function) of the electronic parking brake system off.
If the ignition switch could not be turned ON (READY), turn the ignition switch off and check for DTCs after turning the ignition switch to ON (READY) again.
When the parking brake indicator (red) is illuminated after the electric parking brake switch (electric parking brake switch assembly) has been pulled to the lock side, the maximum amount of braking force is applied if the electric parking brake switch (electric parking brake switch assembly) is pulled to the lock side one more time.
Because P300449 uses 2 trip detection logic, the DTC detection conditions need to be met 2 times.
When P300449 is detected, the ignition switch cannot be turned ON (READY).
Ensure the safety of the areas in front and at the back of the vehicle.
Move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time.
Depressing both the accelerator pedal and brake pedal at the same time causes the HV battery current to flow and ensures that there is no problem with the high-voltage wiring.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P1C8449 is output | A |
| DTCs are not output | B |
| P300449 is output | C |
Post-procedure1
Turn the ignition switch off.
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000
| Result | Proceed to |
|---|---|
| OK | A |
| NG (The connector is not connected securely.) | B |
| NG (The terminals are not making secure contact or are deformed, or water or foreign matter exists in the connector.) | C |
A
B
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA000
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the O70 No. 1 traction battery device box assembly connector.
Disconnect the H44 hybrid vehicle control ECU connector.
Procedure1
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H44,O70)Location & Routingewd_type=routing;type=c,c;code=H44,O70 Click Connector(H44)Instrument Panel>Instrument Panel Wire / Speaker Wire>Hybrid Vehicle Control ECUewd_type=component;type=c;code=H44;pinno=2,27 Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assemblyewd_type=component;type=c;code=O70;pinno=1,4 |
||
| H44-2 (SMRB) - O70-1 (SMRB) | Ignition switch off | Below 1 Ω |
| H44-27 (SMRG) - O70-4 (SMRG) | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the H44 hybrid vehicle control ECU connector.
Reconnect the O70 No. 1 traction battery device box assembly connector.
Install the HV battery upper cover panel.
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the O70 No. 1 traction battery device box assembly connector.
Procedure1
| *a | Front view of wire harness connector
(to No. 1 Traction Battery Device Box Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O70)Location & Routingewd_type=routing;type=c;code=O70 Click Connector(O70)Body>Floor Wire>HV Battery Junction Block Assemblyewd_type=component;type=c;code=O70;pinno=3 |
||
| O70-3 (GND) - Body ground | Ignition switch off | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
Reconnect the O70 No. 1 traction battery device box assembly connector.
Install the HV battery upper cover panel.
OK
NG
| Proceed to |
|---|
| NEXT |
NEXT
Be sure to wear insulated gloves.
Pre-procedure1
Install the service plug grip.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
None.
NEXT
Pre-procedure1
Turn the ignition switch off and wait for 2 minutes or more.
Turn the ignition switch to ON (READY).
Procedure1
According to the display on the GTS, read the Data List and monitor the values of "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" for 3 minutes.
| Tester Display |
|---|
| VL-Voltage before Boosting |
| Hybrid/EV Battery Voltage |
| Result | Proceed to |
|---|---|
| Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is always less than 50 V. | A |
| Difference between "Hybrid/EV Battery Voltage" and "VL-Voltage before Boosting" is 50 V or more | B |
Post-procedure1
Turn the ignition switch off.
A
B