When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| P030000 | Random/Multiple Cylinder Misfire Detected | Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
Engine | B | SAE Code: P0300 |
| P030027 | Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold | An emission deterioration misfire occurs (2 trip detection logic). | ·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on | Engine | B | SAE Code: - |
| P030085 | Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range | A misfire occurs that may damage the three-way catalytic converter (2 trip detection logic). | ·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
Engine | B | SAE Code: - |
| P030100 | Cylinder 1 Misfire Detected | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
Engine | B | SAE Code: P0301 |
| P030200 | Cylinder 2 Misfire Detected | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
Engine | B | SAE Code: P0302 |
| P030300 | Cylinder 3 Misfire Detected | Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
·
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected). ·
An emission deterioration misfire occurs (MIL illuminates). |
·
Open or short in engine wire harness ·
Connector connection ·
Vacuum hose connections ·
Ignition system ·
Fuel injector assembly ·
Fuel pressure ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Compression pressure ·
Valve timing ·
PCV valve and hose ·
PCV hose connections ·
Intake system ·
EGR valve assembly ·
ECM |
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected. |
Engine | B | SAE Code: P0303 |
When DTCs for misfiring cylinders are randomly stored, but DTC P030000 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P030000 is only stored when several misfiring cylinders are detected at the same time.
The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
An excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.
At a normal engine speed, a sufficient amount of misfires to damage the catalyst and occurring within 200 crankshaft revolutions is detected 3 times.
| Required Sensors/Components (Main) | Crankshaft position sensor
Camshaft position sensor |
| Required Sensors/Components (Related) | Engine coolant temperature
Intake air temperature sensor (mass air flow meter) Mass air flow meter |
| Frequency of Operation | Continuous |
| Either of the following conditions is met | (a) or (b) |
| (a) Engine coolant temperature at engine start | Higher than -7°C (19°F) |
| (b) Engine coolant temperature | Higher than 20°C (68°F) |
| Monitor period | Crankshaft 1000 revolutions x 4 |
| Monitor period | Crankshaft 200 revolutions x 3 |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Record the DTC(s) and Freeze Frame Data.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Put the engine in Inspection Mode (Maintenance Mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
Using the GTS, switch the ECM from normal mode to check mode.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE
Start the engine.
Read the misfire counts of each cylinder, Misfire Count Cylinder #1 to Misfire Count Cylinder #3, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the Freeze Frame Data. Perform this step several times.
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.
| Engine speed | Duration |
|---|---|
| Idling | 4.5 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
Check whether misfires have occurred by checking DTCs and Freeze Frame Data.
Do not turn the ignition switch off until the output DTC(s) and Freeze Frame Data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), Freeze Frame Data and other data are cleared.
Record the DTC(s), Freeze Frame Data and misfire counts.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Refer to DTC P010012 for the mass air flow meter circuit.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>P010012
Refer to Fuel Injector Circuit.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>Fuel Injector Circuit
Inspect the fuses for circuits related to this system before performing the following procedure.
Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY
(Select Powertrain in Health Check and then check the time stamp data.)
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR
If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY
In the past, when the primary ignition system (the igniter drive circuit in the ECM, the primary circuit in the ignition coil assembly, the related wire harness, or the connector) was out of order, diagnostic codes from P035113 to P035313 were output. However, these codes are not output in this vehicle.
When a failure in the primary ignition system is suspected, refer to "Catalyst OT Misfire Fuel Cut History", "Catalyst OT Misfire Fuel Cut Cylinder #1 to #3", and "Misfire Count Cylinder #1 to #3" in the Freeze Frame Data, the pending Freeze Frame Data, and the Data List, and confirm in which cylinder the high-frequency misfire was concentrated.
Referring to the following contents of the Freeze Frame Data (or the pending Freeze Frame Data) enables an estimation of which cylinder has misfired and to what degree.
Misfire Count Cylinder #1 to #3: Misfire count according to cylinder.
Catalyst OT Misfire Fuel Cut Cylinder #1 to #3: This expresses that a high-frequency misfire was concentrated in a certain cylinder and that the cylinder's fuel injection was stopped.
If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as Freeze Frame Data.
If the misfire still cannot be reproduced even though the conditions stored in the ECM as Freeze Frame Data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
There was insufficient fuel in the tank.
Improper fuel was used.
The spark plugs have been contaminated.
The problem requires further diagnosis.
After finishing repairs, check the misfire counts of the cylinders (Misfire Count Cylinder #1 to Misfire Count Cylinder #3).
Be sure to confirm that no misfiring cylinder DTCs are stored again by performing the confirmation driving pattern after finishing repairs.
When either Short FT B1S1, Long FT B1S1 in the Freeze Frame Data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (+20% or higher).
When Coolant Temperature in the Freeze Frame Data is below 75°C (167°F), the misfires have occurred only while warming up the engine.
Vehicle body vibrations caused by an extremely imbalanced drive wheel may cause misfire DTCs to be stored.
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P030000, P030027, P030085, P030100, P030200 or P030300 and other DTCs are output | A |
| P030000, P030027, P030085, P030100, P030200 or P030300 is output | B |
If any DTCs other than P030000, P030027, P030085, P030100, P030200 and/or P030300 are output, troubleshoot those DTCs first.
A
B
Check the PCV hose connections.
Check the PCV valve.
Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>PCV VALVE>INSPECTION
PCV hose and PCV valve are connected correctly and are not damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read and note the Misfire RPM and Misfire Load values.
| Tester Display |
|---|
| Misfire RPM |
| Misfire Load |
The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
| Proceed to |
|---|
| NEXT |
NEXT
Read the value displayed on the GTS.
| Tester Display |
|---|
| Catalyst OT Misfire Fuel Cut |
| Data List | Result | Proceed to |
|---|---|---|
| Catalyst OT Misfire Fuel Cut | Avail | A |
| Not Avl | B |
A
B
Using the GTS, confirm the vehicle conditions recorded in the Freeze Frame Data which were present when the DTC was stored.
| Freeze Frame Data Item | Result | Proceed to |
|---|---|---|
| Catalyst OT Misfire Fuel Cut History | ON | A |
| OFF | B |
A
B
Pre-procedure1
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Procedure1
Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #3 displayed on the GTS while performing the Active Test.
| Active Test Display |
|---|
| Prohibit the Catalyst OT Misfire Prevent Fuel Cut |
| Data List Display |
|---|
| Coolant Temperature |
| Misfire Count Cylinder #1 |
| Misfire Count Cylinder #2 |
| Misfire Count Cylinder #3 |
| Result | Proceed to |
|---|---|
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders have equal misfire counts | B |
If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.
Post-procedure1
None.
A
B
Pre-procedure1
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Procedure1
Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #3 displayed on the GTS.
| Tester Display |
|---|
| Coolant Temperature |
| Misfire Count Cylinder #1 |
| Misfire Count Cylinder #2 |
| Misfire Count Cylinder #3 |
Start the engine and allow the engine to idle.
Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #3 displayed on the GTS. If no misfire counts occur in any cylinders, perform procedures [A] and [B] and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].
Read the Misfire Count Cylinder #1 to Misfire Count Cylinder #3 or DTCs displayed on the GTS [B].
| Result | Proceed to |
|---|---|
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders have equal misfire counts | B |
If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.
Post-procedure1
None.
A
B
Inspect the spark plug of the misfiring cylinder.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Perform a spark test.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Pre-procedure1
Disconnect the ECM connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D52,A53)Location & Routingewd_type=routing;type=c,c;code=D52,A53 Click Connector(D52)Engine Compartment>Engine Wire>ECMewd_type=component;type=c;code=D52;pinno=96,95,94 Click Connector(A53)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A53;pinno=6 |
||
| D52-96 (#10) - A53-6 (E1) | Ignition switch ON | 11 to 14 V |
| D52-95 (#20) - A53-6 (E1) | Ignition switch ON | 11 to 14 V |
| D52-94 (#30) - A53-6 (E1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Check the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>REMOVAL
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>M15A-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List twice, when the engine is both cold and warmed up.
| Tester Display |
|---|
| Coolant Temperature |
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Coolant Temperature | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher with all the accessories switched off and shift position N.
Read the Mass Air Flow Sensor while maintaining an engine speed of 2500 rpm.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
| Coolant Temperature |
| Result | Proceed to |
|---|---|
| The value of Mass Air Flow Sensor is between 4.0 and 18.6 gm/sec | A |
| None of the above conditions are met | B |
A
B
Pre-procedure1
Remove the cylinder head cover sub-assembly.
Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.
Procedure1
| *a | Timing Mark |
| *b | TDC Timing Mark |
| *c | Groove |
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration. If the timing marks are not as shown, turn the crankshaft one revolution clockwise.
Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.
The A/C switch and all accessories should be off.
Procedure1
Confirm that the value of Data List item Engine Independent is "Operate" and then check the value of Intake Manifold Absolute Pressure while performing the Active Test.
| Active Test Display |
|---|
| Control the EGR Step Position |
| Data List Display |
|---|
| Intake Manifold Absolute Pressure |
| Coolant Temperature |
| EGR Step Position |
| Engine Independent |
Make sure that the value of Data List item Engine Independent is "Operate" while performing the Active Test.
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
The value of Intake Manifold Absolute Pressure changes in response to the EGR step position when the value of Engine Independent is "Operate".
| - | EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| Intake Manifold Absolute Pressure
(Data List) |
(EGR valve is fully closed) | Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed |
If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).
While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be a malfunctioning.
Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Remove the EGR valve assembly.
Procedure1
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>M15A-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks from intake system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List twice, when the engine is both cold and warmed up.
| Tester Display |
|---|
| Coolant Temperature |
| GTS Display | Condition | Specified Condition |
|---|---|---|
| Coolant Temperature | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Pre-procedure1
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
Procedure1
Read the Data List.
| Tester Display |
|---|
| Engine Speed |
| Mass Air Flow Sensor |
| Coolant Temperature |
Allow the engine to idle until Coolant Temperature is 75°C (167°F) or higher with all the accessories switched off and shift position N.
Read Mass Air Flow Sensor with the engine speed at 2500 rpm.
During charge control, the engine speed is set at idle. Therefore, the engine speed will not increase when the accelerator pedal is depressed. In this case, read the Data List after charge control has completed.
| Result | Proceed to |
|---|---|
| The value of Mass Air Flow Sensor is between 4.0 and 18.6 gm/sec | A |
| None of the above conditions are met | B |
Post-procedure1
None.
A
B
Pre-procedure1
Remove the cylinder head cover sub-assembly.
Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain or belt cover sub-assembly.
Procedure1
| *a | Timing Mark |
| *b | TDC Timing Mark |
| *c | Groove |
Check that the timing marks of the camshaft timing gear assembly and camshaft timing sprocket are at the positions shown in the illustration. If the timing marks are not as shown, turn the crankshaft one revolution clockwise.
Timing marks on camshaft timing gear assembly and camshaft timing sprocket are at the positions shown in the illustration.
If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
Put the engine in Inspection Mode (Maintenance Mode).
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.
The A/C switch and all accessories should be off.
Procedure1
Confirm that the value of Data List item Engine Independent is "Operate" and then check the value of Intake Manifold Absolute Pressure while performing the Active Test.
| Active Test Display |
|---|
| Control the EGR Step Position |
| Data List Display |
|---|
| Intake Manifold Absolute Pressure |
| EGR Step Position |
| Engine Independent |
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
Be sure to return the EGR valve to step 0 when the Active Test is completed.
Do not open the EGR valve 30 steps or more during the Active Test.
The value of Intake Manifold Absolute Pressure changes in response to the EGR step position when the value of Engine Independent is "Operate".
| - | Control the EGR Step Position (Active Test) | |
|---|---|---|
| 0 Steps | 0 to 30 Steps | |
| Intake Manifold Absolute Pressure
(Data List) |
(EGR valve is fully closed) | Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when the EGR valve is fully closed |
If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).
While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be malfunctioning.
Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.
| Result | Proceed to |
|---|---|
| The value of Intake Manifold Absolute Pressure increases by 10 kPa (abs) or more, compared to when the EGR valve was fully closed (0 step) | OK |
| Other than above | NG |
10 kPa = 1.45 psi
Post-procedure1
None.
OK
NG
Pre-procedure1
Remove the EGR valve assembly.
Procedure1
Check if the EGR valve is stuck open.
EGR valve is tightly closed.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Inspect the spark plug of the misfiring cylinder.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL
Perform "Inspection After Repair" after replacing the spark plug.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION
If the result of the spark test is normal, proceed to the next step.
Perform "Inspection After Repair" after repairing or replacing the ignition system.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Measure the cylinder compression pressure of the misfiring cylinder.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Pre-procedure1
Disconnect the ECM connector.
Turn the ignition switch to ON.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D52,A53)Location & Routingewd_type=routing;type=c,c;code=D52,A53 Click Connector(D52)Engine Compartment>Engine Wire>ECMewd_type=component;type=c;code=D52;pinno=96,95,94 Click Connector(A53)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A53;pinno=6 |
||
| D52-96 (#10) - A53-6 (E1) | Ignition switch ON | 11 to 14 V |
| D52-95 (#20) - A53-6 (E1) | Ignition switch ON | 11 to 14 V |
| D52-94 (#30) - A53-6 (E1) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Check the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL INJECTOR>REMOVAL
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Pre-procedure1
Disconnect the mass air flow meter connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D23,D52)Location & Routingewd_type=routing;type=c,c;code=D23,D52 Click Connector(D23)Engine Compartment>Engine Wire>Intake Mass Air Flow Meter Sub-Assemblyewd_type=component;type=c;code=D23;pinno=4,3,2 Click Connector(D52)Engine Compartment>Engine Wire>ECMewd_type=component;type=c;code=D52;pinno=107,139,106 |
||
| D23-4 (VCC) - D52-107 (VCVG) | Always | Below 1 Ω |
| D23-3 (FG) - D52-139 (VG) | Always | Below 1 Ω |
| D23-2 (E2G) - D52-106 (E2G) | Always | Below 1 Ω |
| D23-4 (VCC) or D52-107 (VCVG) - Body ground and other terminals | Always | 10 kΩ or higher |
| D23-3 (FG) or D52-139 (VG) - Body ground and other terminals | Always | 10 kΩ or higher |
| D23-2 (E2G) or D52-106 (E2G) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
If the results of the inspections performed in steps 16 and 23 (READ VALUE USING GTS (MASS AIR FLOW SENSOR)) indicated no problem, proceed to the next step without replacing the mass air flow meter.
Perform "Inspection After Repair" after replacing the mass air flow meter.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off and wait for at least 30 seconds.
NEXT
Pre-procedure1
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Procedure1
Perform the All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P030000, P030027, P030085, P030100, P030200 or P030300.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200 or P030300 is output) |
B |
Post-procedure1
None.
A
B
Check the fuel lines for leaks or blockage.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION