| ● | Non-reusable part | ★ | Precoated part |
| ● | Non-reusable part | ★ | Precoated part |
| *A | w/ Stud Bolt | *B | w/o Stud Bolt |
| ● | Non-reusable part | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 52 | STUD BOLT | - | ( )
|
- | - |
| 53 | RING PIN | - | ( )
|
- | - |
| 54 | STRAIGHT PIN | - | ( )
|
- | - |
| 55 | REAR ENGINE OIL SEAL | 11401L | - | - | - |
| *A | w/ Stud Bolt | - | - |
| ● | Non-reusable part | - | - |
This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
12180E
10.REMOVE OIL FILLER CAP ASSEMBLY
12108A
11.REMOVE OIL FILLER CAP GASKET
12204C
13.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
13470
14.REMOVE CRANKSHAFT PULLEY ASSEMBLY
| *1 | Crankshaft Pulley Set Bolt | - | - |
| *a | Hold | *b | Turn |
Using SST, hold the crankshaft pulley assembly and loosen the crankshaft pulley set bolt. Further loosen the crankshaft pulley set bolt until 2 or 3 threads remain screwed into the crankshaft.
Using SST and the crankshaft pulley set bolt, remove the crankshaft pulley assembly and crankshaft pulley set bolt.
Apply lubricant to the threads and end of SST.
16304
15.REMOVE OUTLET WATER SUB-ASSEMBLY
Using an 8 mm socket wrench, remove the 2 bolts, outlet water sub-aseembly and water outlet gasket from the cylinder head sub-assembly.
16305E
16.REMOVE OUTLET WATER BY-PASS SUB-ASSEMBLY
Using an 8 mm socket wrench, remove the 2 bolts, outlet water by-pass sub-assembly and outlet water pipe gasket from the cylinder head sub-assembly.
11201
17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Using an 8 mm socket wrench, remove the 13 bolts and cylinder head cover sub-assembly from the camshaft housing sub-assembly.
Remove the 5 cylinder head cover gaskets from the cylinder head cover sub-assembly.
Remove the camshaft bearing cap oil hole gasket from the No. 1 camshaft bearing cap.
11193
18.REMOVE SPARK PLUG TUBE GASKET
Using a screwdriver, pry out the 3 spark plug tube gaskets from the cylinder head cover sub-assembly.
Be careful not to damage the cylinder head cover sub-assembly.
Tape the screwdriver tip before use.
12315A
19.REMOVE ENGINE MOUNTING BRACKET RH
13519
22.REMOVE OIL PUMP DRIVE GEAR
23.SET NO. 1 CYLINDER TO TDC (COMPRESSION)
| *a | Approximately 45.32° | *b | Approximately 16.89° |
| *c | Approximately 95° | *d | Timing Mark |
Temporarily install the crankshaft pulley bolt.
Rotate the crankshaft clockwise and align the crankshaft timing gear key as shown in the illustration.
Check that the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.
Remove the crankshaft pulley bolt.
As the exhaust camshaft sub-assembly may rotate counterclockwise strongly when the crankshaft pulley bolt is removed, use a wrench to hold the hexagonal portion of the exhaust camshaft sub-assembly.
13050
24.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
| *a | Loosen | *b | Hexagon Wrench |
| *c | Hold | - | - |
|
Turn | - | - |
Hold the hexagonal portion of the exhaust camshaft sub-assembly with a wrench and turn the camshaft timing gear assembly clockwise to loosen the chain sub-assembly between the camshaft timing exhaust gear assembly and camshaft timing gear assembly.
Push the plunger all the way in then insert the 1.5 mm hexagon wrench into the No. 1 chain tensioner assembly hole.
Using a wrench, hold the hexagonal portion of the intake camshaft sub-assembly.
Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube with the wrench.
Do not disassemble the camshaft timing gear assembly.
Remove the bolt and camshaft timing gear assembly from the intake camshaft sub-assembly
13506
25.REMOVE CHAIN SUB-ASSEMBLY
13521
26.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET
13540
27.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
| *A | w/ Stud Bolt | *B | w/o Stud Bolt |
13559
28.REMOVE CHAIN TENSIONER SLIPPER
13561
29.REMOVE NO. 1 CHAIN VIBRATION DAMPER
13070A
30.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
| *1 | Camshaft Timing Exhaust Gear Assembly | *2 | Camshaft Timing Oil Control Valve Assembly (Exhaust Camshaft Timing Gear Bolt Assembly) |
Using a wrench, hold the hexagonal portion of the exhaust camshaft sub-assembly.
Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly or spark plug tube with the wrench.
Using a 5 mm hexagon socket wrench, remove the 3 bolts.
Remove the camshaft timing exhaust gear assembly and camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) from the exhaust camshaft sub-assembly.
11310
31.REMOVE TIMING CHAIN COVER ASSEMBLY
Remove the timing chain cover assembly by prying between the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly with a screwdriver with its tip wrapped with protective tape.
Be careful not to damage the contact surfaces of the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly, stiffening crankcase assembly and timing chain cover assembly.
13478
32.REMOVE CRANKSHAFT PULLEY SPACER
13471A
33.REMOVE CRANKSHAFT TIMING GEAR KEY
Using a screwdriver, remove the 2 crankshaft timing gear keys from the crankshaft.
Tape the screwdriver tip before use.
11103
34.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY
Uniformly loosen and remove the 14 bolts in the order shown in the illustration.
Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.
Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.
Tape the screwdriver tip before use.
35.REMOVE CAMSHAFT BEARING CAP
| *1 | No. 1 Camshaft Bearing Cap | *2 | No. 2 Camshaft Bearing Cap |
| *3 | No. 3 Camshaft Bearing Cap | *4 | No. 4 Camshaft Bearing Cap |
Remove the 7 bolts in the order shown in the illustration.
Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap from the camshaft housing sub-assembly.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
13501A
36.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY
13502B
37.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY
13801
38.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
13750
39.REMOVE VALVE LASH ADJUSTER ASSEMBLY
13716
40.REMOVE VALVE STEM CAP
11101
41.REMOVE CYLINDER HEAD SUB-ASSEMBLY
|
|
|
Front of Engine | - | - |
Using a 12 mm socket wrench, uniformly loosen the 8 cylinder head set bolts in the order shown in the illustration. Remove the 8 cylinder head set bolts and 8 plate washers.
11115
42.REMOVE CYLINDER HEAD GASKET
11445
43.REMOVE CYLINDER BLOCK WATER JACKET SPACER
|
|
15600A
45.REMOVE OIL FILTER UNION
Using a 12 mm hexagon socket wrench, remove the oil filter union from the stiffening crankcase assembly.
12101A
46.REMOVE OIL PAN DRAIN PLUG
12101
47.REMOVE OIL PAN SUB-ASSEMBLY
| *a | Nut | - | - |
Remove the 9 bolts and 2 nuts.
Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and stiffening crankcase assembly, cut through the applied sealer and remove the oil pan sub-assembly.
Be careful not to damage the contact surfaces of the stiffening crankcase assembly and oil pan sub-assembly.
Be careful not to damage the oil pan sub-assembly flange.
15104
48.REMOVE OIL STRAINER SUB-ASSEMBLY
Using an 8 mm socket wrench, remove the bolt, oil strainer sub-assembly and oil strainer gasket from the stiffening crankcase assembly.
11420
50.REMOVE STIFFENING CRANKCASE ASSEMBLY
Remove the 8 bolts.
Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block sub-assembly at the places shown in the illustration.
Be careful not to damage the contact surfaces of the cylinder block sub-assembly and stiffening crankcase assembly.
Tape the screwdriver tip before use.
51.REMOVE STRAIGHT SCREW PLUG
Using a 10 mm hexagon socket wrench, remove the straight screw plug from the stiffening crankcase assembly.
52.REMOVE STUD BOLT
|
|
| *A | w/ Stud Bolt | - | - |
Using an E8 "TORX" socket wrench, remove the stud bolt shown in the illustration from the cylinder head sub-assembly.
Using an E6 "TORX" socket wrench, remove the stud bolt shown in the illustration from the timing chain cover assembly.
Using an E6 "TORX" socket wrench, remove the stud bolt shown in the illustration from the stiffening crankcase assembly.
53.REMOVE RING PIN
|
|
54.REMOVE STRAIGHT PIN
|
|
11401L
55.REMOVE REAR ENGINE OIL SEAL