| *A | for Front Pssenger Side | *B | for Driver Side |
|
MP grease | - | - |
| *A | for Driver Side | *B | for Front Pssenger Side |
| ● | Non-reusable part |
|
MP grease |
| *A | for Type A | *B | for Type B |
| ● | Non-reusable part |
|
MP grease |
| ★ | Precoated part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front door removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the LH side and RH side.
The following procedure is for the RH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2. CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>REMOVAL
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
67491A
3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)
5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)
67655
6.REMOVE FRONT DOOR TRIM GARNISH
|
Remove in this Direction | - | - |
67601
7.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Using a screwdriver with its tip wrapped in protective tape, disengage the claw to open the front door inside handle bezel plug.
| *1 | Front Door Inside Locking Cable Assembly | *2 | Front Door Lock Remote Control Cable Assembly |
|
Place Hands Here |
|
Remove in this Direction |
Disengage the clips as shown in the illustration.
Disengage the front door trim board sub-assembly with the front door glass inner weatherstrip, front door vent seal and front door panel protector as shown in the illustration.
Disengage the guides to disconnect the front door inside locking cable assembly and front door lock remote control cable assembly to remove the front door trim board sub-assembly as shown in the illustration.
69205
8.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
69283A
9.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
68171B
10.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP
|
Remove in this Direction | - | - |
Disengage the claws to remove the front door glass inner weatherstrip with the front vent seal and front door panel protector as shown in the illustration.
67837A
11.REMOVE FRONT DOOR VENT SEAL
67855B
12.REMOVE FRONT DOOR PANEL PROTECTOR
86160
13.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
67831
14.REMOVE FRONT DOOR SERVICE HOLE COVER
Turn the 3 front door service hole cover clips 45° to remove it clips as shown in the illustration.
Disengage the guide and clamp to separate the wire harness from the front door service hole cover.
Disengage the clips to remove the front door service hole cover.
8983A
15.REMOVE SIDE AIR BAG PRESSURE SENSOR
68101
16.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the hole plug.
| *A | for Driver Side | *B | for Front Passenger Side |
| *a | Bolt | - | - |
for Driver Side:
1. Connect the multiplex network master switch assembly.
for Front Passenger Side:
1. Connect the power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
| *A | for Driver Side | *B | for Front Passenger Side |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disconnect the cable from the negative (-) auxiliary battery terminal.
for Driver Side:
1. Disconnect the multiplex net work master switch assembly.
for Front Passenger Side:
1. Disconnect the power window regulator switch assembly.
Remove the 2 bolts.
Remove the front door glass sub-assembly as shown in the illustration.
Do not damage the front door glass sub-assembly.
69801
17.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY
68141C
18.REMOVE FRONT DOOR GLASS RUN
67403F
19.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
|
Remove in this Direction | - | - |
67401F
20.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
69220
21.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
|
Remove in this Direction | - | - |
w/ Entry and Start System:
1. Disengage the claws.
2. Using a screwdriver with its tip wrapped in protective tape, disconnect the connector.
Disengage the 2 claws and move the lever as shown in the illustration.
Remove the front door outside handle assembly as shown in the illustration.
22.REMOVE HOLE PLUG
23.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
Using a T30 "TORX" socket wrench, loosen the screw.
Remove the front door lock cylinder assembly.
69217D
24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the claws and guides to remove the front door outside handle cover.
69241H
25.REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD
69242H
26.REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD
69030A
27.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY
69318C
28.REMOVE DOOR LOCK WIRING HARNESS SEAL
69201A
29.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
| *A | w/ Entry and Start System | - | - |
|
Remove in this Direction | - | - |
w/ Entry and Start System:
1. Disengage the clamp to separate the wire harness.
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the guides to remove the front door outside handle frame sub-assembly as shown in the illustration.
69311A
30.REMOVE FRONT DOOR LOCK OPEN ROD
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
68160C
31.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>REMOVAL
32.REMOVE HOLE COVER
75073
33.REMOVE FRONT DOOR OUTSIDE LOWER MOULDING SUB-ASSEMBLY
67835E
34.REMOVE NO. 2 FRONT DOOR SERVICE HOLE SEAL
87910
35.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
67495C
36.REMOVE FRONT DOOR FRONT LOWER FRAME COVER UPPER
68610B
37.REMOVE FRONT DOOR CHECK ASSEMBLY
67861
38.REMOVE FRONT DOOR WEATHERSTRIP
67001A
39.REMOVE FRONT DOOR PANEL CUSHION
75921C
40.REMOVE NO. 1 BLACK OUT TAPE
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Front Door)>REMOVAL
75925
41.REMOVE NO. 3 BLACK OUT TAPE
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Front Door)>REMOVAL
67837B
42.REMOVE FRONT DOOR DUST PROOF SEAL
for Type A:
Disengage the claws to remove the 3 front door dust proof seals.
Disengage the claws to remove the 3 reardoor dust proof seals.
for Type B:
Disengage the claws to remove the 2 front door dust proof seals.