| *1 | BUTYL TAPE | - | - |
| ● | Non-reusable part |
|
MP grease |
| *A | for Type A | *B | for Type B |
| ● | Non-reusable part |
|
MP grease |
| ★ | Precoated part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear door removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the LH side and RH side.
The following procedure is for the RH side.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>REMOVAL
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
3.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL
67603
4.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Using a screwdriver with its tip wrapped in protective tape, open the rear door inside handle bezel plug.
Remove the 3 screws.
|
Place Hands Here |
|
Remove in this Direction |
Disengage the clips as shown in the illustration.
Disengage the rear door trim board sub-assembly with the rear door glass inner weatherstrip and rear door belt seal as shown in the illustration.
Disengage the guides to disconnect the rear door inside locking cable assembly and rear door lock remote control cable assembly to remove the rear door trim board sub-assembly as shown in the illustration.
69205A
5.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
69283A
6.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
68173B
7.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP
|
Remove in this Direction | - | - |
Disengage the claws to remove the rear door glass inner weatherstrip with the rear door belt front seal as shown in the illustration.
68196B
8.REMOVE REAR DOOR BELT FRONT SEAL
68198
9.REMOVE REAR DOOR BELT REAR SEAL
86160B
10.REMOVE REAR SPEAKER ASSEMBLY
67841E
11.REMOVE REAR DOOR SERVICE HOLE COVER
Remove the rear door service hole cover.
Remove any remaining butyl tape from the rear door panel.
68142C
12.REMOVE REAR DOOR GLASS RUN
68103
13.REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Connect the rear power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the rear door glass sub-assembly so that the door glass bolts can be seen.
|
Remove in this Direction | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the rear power window regulator switch assembly.
Remove the 2 bolts.
Remove the rear door glass sub-assembly as shown in the illustration.
Do not damage the front door glass subassembly.
68011
14.REMOVE REAR DOOR QUARTER WINDOW GLASS SUB-ASSEMBLY
|
Remove in this Direction | - | - |
67447C
15.REMOVE REAR DOOR WINDOW GUIDE PLATE LOWER
69803
16.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY
69318D
18.REMOVE DOOR LOCK WIRING HARNESS SEAL
69210
19.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY
|
Remove in this Direction | - | - |
69227J
20.REMOVE REAR DOOR OUTSIDE HANDLE COVER
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the claws to remove the rear door outside handle cover.
69241G
21.REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD
69242G
22.REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD
69203A
23.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
|
Remove in this Direction | - | - |
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the guides to remove the rear door outside handle frame sub-assembly as shown in the illustration.
68180C
24.REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>REMOVAL
75923C
25.REMOVE NO. 2 BLACK OUT TAPE
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Rear Door)>REMOVAL
68630
26.REMOVE REAR DOOR CHECK ASSEMBLY
67871
27.REMOVE REAR DOOR WEATHERSTRIP
67887F
28.REMOVE NO. 2 REAR DOOR WEATHERSTRIP
75873
29.REMOVE QUARTER PANEL WHEEL OPENING MOULDING RH
75077
30.REMOVE REAR DOOR OUTSIDE LOWER MOULDING SUB-ASSEMBLY
67837C
31.REMOVE REAR DOOR DUST PROOF SEAL
for Type A:
Disengage the claws to remove the 3 rear door dust proof seals.
When installing, install 2 dust proof seals in the same way as for type B.
for Type B:
Disengage the claws to remove the 2 rear door dust proof seals.