Home › Brake › BRAKE (REAR) › REAR BRAKE (for AWD) › 2020.08–2021.07
RM3700E _54 Brake _093728 BRAKE (REAR) _0447171 REAR BRAKE(for AWD) A

BRAKE (REAR)  REAR BRAKE(for AWD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C450151N02
6.417,0.281 6.802,0.281 false 6.417,0.656 6.771,0.656 false 6.417,1.073 6.813,1.073 false 2.708,0.156 2.875,0.156 2.875,0.156 3.156,0.49 false 4.302,0.594 4.531,0.813 4.531,0.813 4.698,0.813 false 4.021,1.25 4.406,1.25 false 4.635,5.063 5.021,5.063 false 0.917,1.177 1.458,1.177 false 5.302,0.167 5.583,0.521 0.281,0.354 18 false 1 5.448,0.208 5.885,0.49 0.438,0.281 12 false (*A) 5.74,0.177 6.365,0.552 0.625,0.375 18 false , 4 6.25,0.51 6.615,0.865 0.365,0.354 18 false 3 6.063,0.208 6.5,0.49 0.438,0.281 12 false (*A) 6.229,0.938 6.594,1.292 0.365,0.354 18 false 5 4.448,4.927 4.813,5.281 0.365,0.354 18 false 2 5.031,0.667 5.396,1.021 0.365,0.354 18 false 7 2.521,0.021 2.885,0.375 0.365,0.354 18 false 8 4.458,1.188 4.896,1.469 0.438,0.281 10 false ● 2.719,0.792 3.156,1.073 0.438,0.281 10 false x2 0.74,1.052 1.104,1.406 0.365,0.354 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 REAR WHEEL - - - -
3 PERFORM REAR BRAKE PAD REPLACEMENT MODE - - - (Click here)
4 DISABLE BRAKE CONTROL - (Click here) - -
5 BRAKE FLUID - - - (Click here)
6 REAR SHOCK ABSORBER ASSEMBLY 48540 (Click here) - -
7 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A (Click here) - -
8 PARKING BRAKE ACTUATOR ASSEMBLY 46310B (Click here) - -

*A for HV Model - -
● Non-reusable part - -

C445223N04
4.583,2.583 6.083,4.167 1.5,1.583 2.802,1.583 4.302,3.167 1.5,1.583 2.083,3.5 3.24,4.25 1.156,0.75 0.99,0.583 2.438,2 1.448,1.417 5.938,0.625 6.271,0.625 false 6.5,0.99 6.5,1.323 false 5.177,0.75 5.51,0.75 false 5.792,2.01 6.125,2.01 false 6.094,3.417 6.427,3.417 false 2.458,2.75 2.792,2.75 false 1.854,3.896 2.083,3.896 false 0.656,1.333 0.99,1.333 false 6.323,0.542 6.5,0.75 0.177,0.208 10 false ● 6.427,1.354 6.646,1.521 0.219,0.167 10 false ● 4.948,0.646 5.365,1.01 0.417,0.365 18 false 9 4.323,0.885 4.583,1.219 0.26,0.333 10 false x2 6.167,1.875 6.604,2.26 0.438,0.385 18 false 10 6.74,3.281 7.083,3.615 0.344,0.333 18 false 12 2.167,2.604 2.5,2.938 0.333,0.333 18 false 11 1.573,3.75 1.958,4.083 0.385,0.333 18 false 12 1.458,3.802 1.677,3.969 0.219,0.167 10 false ● 0.365,1.198 0.698,1.531 0.333,0.333 18 false 12

Procedure Part Name Code
Z101186

Z101188

Z101187

9 REAR FLEXIBLE HOSE 47319F - - -
10 REAR DISC BRAKE CYLINDER ASSEMBLY 47850 - - -
11 REAR DISC BRAKE PAD 04466 - - -
12 REAR DISC BRAKE ANTI-SQUEAL SHIM KIT 04946 (Click here) - -

● Non-reusable part - -

C449775N03
5.333,0.667 6.917,2.083 1.583,1.417 3.25,1.75 3.417,1.75 3.417,1.75 3.5,1.51 false 3.958,0.885 4.083,0.75 4.083,0.75 4.25,0.75 false 3.448,0.646 3.635,0.292 3.635,0.292 3.802,0.292 false 4.917,2.615 4.917,2.948 false 6.167,2.083 6.167,2.333 false 2.656,2.438 2.323,2.438 false 2.854,0.385 2.604,0.385 false 2.729,1.01 2.479,1.01 false 2.896,2.302 3.448,2.656 0.552,0.354 18 false 17 2.927,1.573 3.479,1.927 0.552,0.354 18 false 15 2.781,1.615 3.083,1.885 0.302,0.271 10 false ● 4.438,0.604 4.99,0.958 0.552,0.354 18 false 15 4.302,0.656 4.604,0.927 0.302,0.271 10 false ● 3.854,0.219 4.438,0.594 0.583,0.375 10 false ● *1 2.281,0.271 2.833,0.625 0.552,0.354 18 false 14 3.708,2.333 4.052,2.573 0.344,0.24 10 false x2 4.813,2.969 5.365,3.323 0.552,0.354 18 false 16 6.208,2.281 6.76,2.635 0.552,0.354 18 false 13 2.177,0.896 2.729,1.25 0.552,0.354 18 false 14

Procedure Part Name Code
Z101186

Z101188

Z101187

13 REAR DISC BRAKE PAD SUPPORT PLATE - (Click here) - -
14 REAR DISC BRAKE CYLINDER SLIDE PIN - (Click here) - -
15 NO. 1 BUSH DUST BOOT 47775B - - -
16 REAR DISC BRAKE CYLINDER MOUNTING 47822 - - -
17 REAR DISC 42321 (Click here) - -

*1 NO. 1 REAR DISC BRAKE CYLINDER SLIDE BUSH - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear brake removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC (C13CD00, C13CE00, C140000) may be stored. As there is no malfunction, clear the DTC. (for HV Model)

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)



HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used. (for HV Model)

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

for HV Model: Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

Make sure to read the precautions of the electric parking brake system before removing the rear brake assembly.

for HV Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model)>PRECAUTION

for Gasoline Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model)>PRECAUTION



Hide 2.REMOVE REAR WHEEL

Hide 4.DISABLE BRAKE CONTROL (for HV Model)

Z101186

Click here(Click here)

Hide 5.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 48540 6.DISCONNECT REAR SHOCK ABSORBER ASSEMBLY

Z101186

Click here(Click here)

Hide 890C0A 7.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

Z101186

Click here(Click here)

Hide 46310B 8.REMOVE PARKING BRAKE ACTUATOR ASSEMBLY

Z101186

Click here(Click here)

Hide 47319F 9.SEPARATE REAR FLEXIBLE HOSE

a.
C445669


Hide 47850 10.REMOVE REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C445670


Hide 04466 11.REMOVE REAR DISC BRAKE PAD

a.
C445671


Hide 04946 12.REMOVE REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

Z101186

Click here(Click here)

Hide 13.REMOVE REAR DISC BRAKE PAD SUPPORT PLATE

Z101186

NOTICE:

Each rear disc brake pad support plate has a different shape. Be sure to put an identification mark on each rear disc brake pad support plate so that it can be reinstalled to its original position.



a.
C445672


Hide 14.REMOVE REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C445673N02
0.76,0.052 1.042,0.406 0.281,0.354 18 false i 3.99,0.083 4.271,0.438 0.281,0.354 18 false ii

i.

Remove the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin from the rear disc brake cylinder mounting.


ii.

Using a screwdriver with its tip wrapped with protective tape, remove the rear disc brake cylinder slide bushing from the rear No. 2 disc brake cylinder slide pin.

NOTICE:

Do not damage the rear No. 2 disc brake cylinder slide pin.




Hide 47775B 15.REMOVE NO. 1 BUSH DUST BOOT

a.
C445674


Hide 47822 16.REMOVE REAR DISC BRAKE CYLINDER MOUNTING

a.
C445675


Hide 42431 17.REMOVE REAR DISC

a.
C445676C03
2.771,1.052 3.354,1.052 true 3.198,1.042 3.198,1.104 3.198,1.104 3.365,1.104 true 1.927,0.073 2.365,0.375 0.438,0.302 18 true i, ii 2.583,0.969 2.896,1.167 0.313,0.198 10 false *a
*a Matchmark - -


i.

Put matchmarks on the rear disc and rear axle hub and bearing assembly.


ii.

Remove the rear disc.