Home › Brake › BRAKE (REAR) › REAR BRAKE (for AWD) › 2020.08–2021.07
RM3700E _54 Brake _093728 BRAKE (REAR) _0447171 REAR BRAKE(for AWD) A

BRAKE (REAR)  REAR BRAKE(for AWD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C449776N03
5.333,0.667 6.917,2.083 1.583,1.417 3.115,2.896 3.896,3.063 0.781,0.167 3.063,2.854 3.938,3.104 0.875,0.25 3.25,1.833 3.417,1.833 3.417,1.833 3.469,1.49 false 3.927,0.844 4.177,0.563 4.177,0.563 4.344,0.563 false 3.448,0.646 3.635,0.292 3.635,0.292 3.802,0.292 false 4.917,2.604 4.917,2.938 false 2.49,0.406 2.854,0.406 false 2.615,0.406 2.615,1.031 2.615,1.031 2.729,1.031 false 6.177,2.083 6.177,2.302 false 2.656,2.438 2.323,2.438 false 3.542,2.563 3.542,2.896 false 2.906,2.302 3.458,2.656 0.552,0.354 18 false 1 3.083,1.688 3.635,2.042 0.552,0.354 18 false 3 2.927,1.76 3.229,2.031 0.302,0.271 10 false ● 4.802,0.438 5.354,0.792 0.552,0.354 18 false 3 4.635,0.51 4.938,0.781 0.302,0.271 10 false ● 3.865,0.219 4.406,0.583 0.542,0.365 10 false ● *1 2.302,0.281 2.854,0.635 0.552,0.354 18 false 4 3.708,2.333 4.052,2.573 0.344,0.24 10 false x2 4.854,2.969 5.406,3.323 0.552,0.354 18 false 2 6.24,2.292 6.792,2.646 0.552,0.354 18 false 5 3.135,2.917 3.969,3.083 0.833,0.167 8 false 107 (1091, 79)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DISC 42431 (Click here) - -
2 REAR DISC BRAKE CYLINDER MOUNTING 47822 - - -
3 NO. 1 BUSH DUST BOOT 47775B (Click here) - -
4 REAR DISC BRAKE CYLINDER SLIDE PIN - (Click here) - -
5 REAR DISC BRAKE PAD SUPPORT PLATE - (Click here) - -

*1 NO. 1 REAR DISC BRAKE CYLINDER SLIDE BUSH - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) ● Non-reusable part
V100135

Lithium Soap Base Glycol Grease - -

C450153N01
4.583,2.583 6.083,4.167 1.5,1.583 2.802,1.583 4.302,3.167 1.5,1.583 2.083,3.5 3.24,4.25 1.156,0.75 0.99,0.583 2.438,2 1.448,1.417 6.25,1.323 7.021,1.51 0.771,0.188 6.208,1.292 7.073,1.552 0.865,0.26 3.115,0.688 3.906,0.854 0.792,0.167 3.073,0.646 3.948,0.896 0.875,0.25 5.938,0.625 6.271,0.625 false 6.5,0.99 6.5,1.323 false 5.104,0.594 5.406,0.594 false 5.792,2.01 6.125,2.01 false 6.094,3.417 6.427,3.417 false 2.427,2.594 2.792,2.594 false 1.781,3.875 2.083,3.875 false 0.656,1.333 0.99,1.333 false 3.906,0.771 4.24,0.771 false 6.323,0.542 6.5,0.75 0.177,0.208 10 false ● 6.052,1.333 6.271,1.5 0.219,0.167 10 false ● 4.938,0.448 5.344,0.76 0.406,0.313 18 false 9 4.5,0.719 4.76,1.052 0.26,0.333 10 false x2 6.51,1.885 6.938,2.219 0.427,0.333 18 false 8 6.76,3.271 7.104,3.604 0.344,0.333 18 false 6 2.219,2.458 2.552,2.792 0.333,0.333 18 false 7 1.615,3.729 1.948,4.063 0.333,0.333 18 false 6 1.448,3.813 1.667,3.979 0.219,0.167 10 false ● 0.385,1.198 0.719,1.531 0.333,0.333 18 false 6 6.281,1.354 7.052,1.51 0.771,0.156 8 false 30.4 (310, 22) 3.146,0.708 4.01,0.875 0.865,0.167 8 false 34.3 (350, 25)

Procedure Part Name Code
Z101186

Z101188

Z101187

6 REAR DISC BRAKE ANTI-SQUEAL SHIM KIT 04946 (Click here) - -
7 REAR DISC BRAKE PAD 04466 (Click here) - -
8 REAR DISC BRAKE CYLINDER ASSEMBLY 47850 (Click here) - -
9 REAR FLEXIBLE HOSE 46310B (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) ● Non-reusable part

C449777N02
2.01,1.031 2.969,1.208 0.958,0.177 1.969,0.99 3.01,1.26 1.042,0.271 0.583,2.229 1.302,2.396 0.719,0.167 0.531,2.188 1.344,2.448 0.813,0.26 6.469,0.25 6.802,0.25 false 6.396,1.052 6.75,1.052 false 6.417,1.604 6.823,1.604 false 2.813,0.167 2.979,0.167 2.979,0.167 3.188,0.427 false 4.292,0.604 4.438,1.031 4.438,1.031 4.604,1.031 false 3.969,1.302 4.354,1.302 false 4.635,5.063 5.021,5.063 false 2.469,1.031 2.469,0.865 2.469,0.865 2.688,0.688 false 1.073,1.188 1.458,1.188 false 1.031,2.229 1.031,1.938 false 4.938,0.115 5.5,0.531 0.563,0.417 18 false , 16 5.375,0.146 5.813,0.427 0.438,0.281 12 false (*A) 5.667,0.115 6.594,0.51 0.927,0.396 18 false , 18 6.052,0.385 6.552,0.719 0.5,0.333 18 false , 21 6.146,0.146 6.583,0.427 0.438,0.281 12 false (*B) 5.667,1.49 6.5,1.833 0.833,0.344 18 false 15, 17 4.323,4.917 4.688,5.271 0.365,0.354 18 false 20 4.896,0.896 5.26,1.25 0.365,0.354 18 false 11 2.49,0.031 2.854,0.385 0.365,0.354 18 false 10 4.406,1.229 4.844,1.51 0.438,0.281 10 false ● 2.875,0.615 3.313,0.896 0.438,0.281 10 false x2 5.448,0.406 6.073,0.781 0.625,0.375 18 false 19 5.74,0.417 6.177,0.698 0.438,0.281 12 false (*A) 2.031,1.063 2.99,1.26 0.958,0.198 8 false 8.4 (86, 74 in.*lbf) 4.656,0.094 5.521,0.479 0.865,0.385 18 false 13 5.333,0.948 6.24,1.313 0.906,0.365 18 false 22, 23 6.052,0.969 6.49,1.25 0.438,0.281 12 false (*A) 0.646,2.26 1.344,2.427 0.698,0.167 8 false 49 (500, 36) 0.385,1.052 1.104,1.396 0.719,0.344 18 false 12, 14

Procedure Part Name Code
Z101186

Z101188

Z101187

10 PARKING BRAKE ACTUATOR ASSEMBLY 46310B (Click here) - -
11 NO. 2 PARKING BRAKE WIRE ASSEMBLY 890C0A (Click here) - -
12 TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY 48540 (Click here) - -
13 STABILIZE SUSPENSION - (Click here) - -
14 FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY 48540 (Click here) - -
15 ADD BRAKE FLUID - - (Click here) -
16 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - (Click here) - -
17 BLEED BRAKE LINE - - (Click here) -
18 BLEED REAR DISC BRAKE CYLINDER ASSEMBLY 47850 (Click here) - -
19 BLEED REAR DISC BRAKE CYLINDER ASSEMBLY 47850 (Click here) - -
20 REAR WHEEL - - - -
21 INSPECT AND ADJUST REAR WHEEL ALIGNMENT - (Click here) - -
22 NORMAL CONDITION RECOVERY - - - (Click here)
23 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

*A for HV Model *B for Gasoline Model
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) ● Non-reusable part
V100135

Lithium soap base glycol grease - -

CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the front disc brake pads, always perform a road test to check the braking performance and check for vibrations.

·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC [C13CD00, C13CE00, C140000] may be stored. As there is no malfunction, clear the DTC. (for HV Model)

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

Z101186

NOTICE:

When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



a.
C445676C04
3.406,1.042 3.906,1.052 true 3.396,1.115 3.563,1.115 3.563,1.115 3.563,1.042 true 1.906,0.063 2.281,0.417 0.375,0.354 18 true i, ii 3.938,0.969 4.25,1.167 0.313,0.198 10 true *a
*a Matchmark - -


i.

Align the matchmarks of the rear disc and rear axle hub and bearing assembly, and install the rear disc.



Hide 47822 2.INSTALL REAR DISC BRAKE CYLINDER MOUNTING

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)

Hide 47775B 3.INSTALL NO. 1 BUSH DUST BOOT

a.
C445694C02
3.927,0.104 4.208,0.458 0.281,0.354 18 false ii 1.156,0.146 1.438,0.5 0.281,0.354 18 false i
V100155

Lithium Soap Base Glycol Grease - -


i.

Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



ii.

Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.



Hide 4.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C445695C02
2.844,1.906 3.51,2.156 true 2.594,2.969 3.521,3.313 true 0.573,0.083 0.854,0.438 0.281,0.354 18 false i 3.26,1.198 3.542,1.552 0.281,0.354 18 false ii 3.969,0.063 4.25,0.417 0.281,0.354 18 false iii 2.406,2.865 2.688,3.219 0.281,0.354 10 false *1 2.646,1.854 2.927,2.208 0.281,0.354 10 false *2 2,2.021 2.5,2.375 0.5,0.354 18 false iv, v
*1 Rear No. 1 Disc Brake Cylinder Slide Pin *2 Rear No. 2 Disc Brake Cylinder Slide Pin
V100155

Lithium Soap Base Glycol Grease - -


i.

Apply a light layer of lithium soap base glycol grease to the contact surface of the rear No. 2 disc brake cylinder slide pin.


ii.

Install a new rear disc brake cylinder slide bushing to the rear No. 2 disc brake cylinder slide pin.


iii.

Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin.


iv.

Install the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin to the rear disc brake cylinder mounting.


v.

Push the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin into each rear disc brake bushing dust boot to engage the pins to the boots.



Hide 5.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

Z101186

NOTICE:

Be sure to install each rear disc brake pad support plate in the correct position and direction.



Hide 04946 6.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM KIT

Hide 04466 7.INSTALL REAR DISC BRAKE PAD

a.
C449835C01
2.469,0.719 2.708,0.719 false 1.063,0.865 1.552,0.865 true 2.75,0.646 3.063,0.802 0.313,0.156 10 false *a 0.885,0.813 1.198,0.969 0.313,0.156 10 false *b 0.542,0.104 0.833,0.396 0.292,0.292 18 false i 4.24,0.115 4.427,0.448 0.188,0.333 18 false ii
*a Inner Side (Brown) *b Outer Side (Green)


i.

Check the rear disc brake pad has an identification mark, be sure to confirm the installation location.


ii.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:

Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.




Hide 47850 8.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

Z101186

NOTICE:

If bleeding of air from the rear brake cylinder assembly will be performed, reuse the bolts. If bleeding of air from the rear brake cylinder assembly will not be performed, install new bolts.



Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)

Hide 47319F 9.CONNECT REAR FLEXIBLE HOSE

Z101186

NOTICE:

Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.



Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

Hide 46310B 10.INSTALL PARKING BRAKE ACTUATOR ASSEMBLY

Z101186

Click here(Click here)

Hide 890C0A 11.INSTALL NO. 2 PARKING BRAKE WIRE ASSEMBLY

Z101186

Click here(Click here)

Hide 48540 12.TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY

Z101186

Click here(Click here)

Hide 13. STABILIZE SUSPENSION

Z101186

Click here(Click here)

Hide 48540 14.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY

Hide 16.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

Z101186

Click here(Click here)

Hide 47850 18.BLEED REAR DISC BRAKE CYLINDER ASSEMBLY (for Gasoline Model)

Z101186

CAUTION:

If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder assembly.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

While performing air bleeding of the rear disc brake cylinder assembly, the bolts can be reused during the bleeding procedure. After air bleeding is complete, replace the bolts with new ones.




a.
C445220N01
0.365,0.052 0.646,0.406 0.281,0.354 18 false i

i.

Perform the following procedure.

1. Perform the procedure to enter rear disc brake pad replacement mode 5 times.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model)>TEST MODE PROCEDURE

2. Release the parking brake.

3. Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for 2WD)>REMOVAL

4. Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and separate the rear disc brake cylinder assembly from the rear disc brake cylinder mounting.(*1)

5. Hold the rear disc brake cylinder assembly horizontally, then tilt it 45° toward the bleeder plug side as shown in the illustration.(*2)

6. Temporarily install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.(*3)

7. Remove the center No. 1 cowl top ventilator louver.

Click hereGeneral>MAINTENANCE>BRAKE FLUID (for Gasoline Model)>REPLACEMENT

8. Remove the brake master cylinder reservoir filler cap assembly.

Click hereGeneral>MAINTENANCE>BRAKE FLUID (for Gasoline Model)>REPLACEMENT

9. Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

NOTICE:
·

Make sure that there is sufficient brake fluid in the reservoir.

·

Do not remove the filter from the brake master cylinder reservoir assembly and be sure to fill the brake master cylinder reservoir assembly with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.

·

If brake fluid leaks onto any painted surface, immediately wash it off.



10. Remove the rear disc brake bleeder plug cap.

11. Connect a vinyl tube to the rear disc brake bleeder plug.

12. Depress the brake pedal several times, and then loosen the rear disc brake bleeder plug with the pedal depressed.(*4)

13. When fluid stops coming out, tighten the rear disc brake bleeder plug and release the brake pedal.(*5)

NOTICE:

Repeat steps (*4) through (*5) until there are no signs of air in the brake fluid.


14. Repeat steps (*1) through (*5) 3 times.

NOTICE:

If there is still air in the system after performing steps (*1) through (*5) 3 times, repeat the steps (*1) through (*5) until the air has been bled.


15. Tighten the rear disc brake bleeder plug completely.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)

16. Install the rear disc brake bleeder plug cap.

17. Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with 2 new bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)

18. Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for 2WD)>INSTALLATION

19. Inspect for brake fluid leaks.

20. Inspect the brake fluid level in the reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for Gasoline Model)>ON-VEHICLE INSPECTION

21. Install the brake master cylinder reservoir filler cap assembly.

Click hereGeneral>MAINTENANCE>BRAKE FLUID (for Gasoline Model)>REPLACEMENT

22. Install the center No. 1 cowl top ventilator louver.

Click hereGeneral>MAINTENANCE>BRAKE FLUID (for Gasoline Model)>REPLACEMENT



Hide 47850 19.BLEED REAR DISC BRAKE CYLINDER ASSEMBLY (for HV Model)

Z101186

CAUTION:

If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder assembly.


NOTICE:
·

Perform air bleeding while maintaining the brake fluid level between the MAX and MIN lines on the brake fluid reservoir.

·

Do not allow brake fluid to contact any painted surface. If brake fluid leaks onto any painted surface, immediately wash it off.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

While performing air bleeding of the rear disc brake cylinder assembly, the bolts can be reused during the bleeding procedure. After air bleeding is complete, replace the bolts with new ones.




a.
C445220N01
0.365,0.052 0.646,0.406 0.281,0.354 18 false i

i.

Perform the following procedure.

1. Perform the procedure to enter rear disc brake pad replacement mode 5 times.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model)>UTILITY

2. Release the parking brake.

3. Force air within the rear disc brake cylinder assembly to accumulate at the rear disc brake bleeder plug.(*1)

(a) Disable brake control.

Click hereBrake>BRAKE (REAR)>REAR BRAKE (for 2WD)>REMOVAL

(b) Disconnect the No. 2 parking brake wire assembly connector.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for 2WD)>REMOVAL

(c) Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and separate the rear disc brake cylinder assembly from the rear disc brake cylinder mounting.

(d) Hold the rear disc brake cylinder assembly horizontally, then tilt it 45° toward the bleeder plug side as shown in the illustration.

(e) Temporarily install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.

(f) Connect the No. 2 parking brake wire assembly connector.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for 2WD)>INSTALLATION

(g) Connect the reservoir level switch connector.

(h) Connect the cable to the negative (-) auxiliary battery terminal.

Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>INSTALLATION

(i) Turn the ignition switch ON.

(j) Depress the brake pedal and release it.

(k) Apply the parking brake.

4. Enter ECB (Electronically Controlled Brake system) Invalid Mode.(*2)

NOTICE:
·

Performing the following procedure enters ECB (Electronically Controlled Brake system) Invalid Mode without using the GTS.

·

ECB (Electronically Controlled Brake system) Invalid Mode allows the brake lines to be bled without using the GTS.

·

The brake warning light blinks (yellow) to indicate that ECB (Electronically Controlled Brake system) Invalid Mode is selected.

·

Be sure to confirm that the brake warning light is blinking (yellow) throughout the brake line bleeding procedure.

·

If any of the following conditions are met, ECB (Electronically Controlled Brake system) Invalid Mode is canceled and the brake warning light (yellow) turns off. Do not allow ECB (Electronically Controlled Brake system) Invalid Mode to be canceled while bleeding the brake lines or DTCs may be stored.

The shift lever is moved from P to any other position.
The ignition switch to ON.
The ignition switch is turned off.
The parking brake is released.
The vehicle speed is more than 0 km/h (0 mph).

·

Do not rotate any brake disc while ECB (Electronically Controlled Brake system) Invalid Mode is selected.

·

Although the brake warning light (yellow) will blink and a buzzer will sound while performing brake line bleeding, this is not a malfunction.



(a) Perform the procedure listed below within 1 minute.

1.

Turn the power switch on (IG) with the shift lever in P and parking brake applied.

2.

Move the shift lever to N and then depress the brake pedal more than 8 times within 5 seconds.

3.

Move the shift lever to P and then depress the brake pedal more than 8 times within 5 seconds.

4.

Move the shift lever to N and then depress the brake pedal more than 8 times within 5 seconds.

5.

Move the shift lever to P.


(b) Check that the brake warning light is blinking (yellow).

5. Remove the center No. 1 cowl top ventilator louver.

Click hereGeneral>MAINTENANCE>BRAKE FLUID (for HV Model)>REPLACEMENT

6. Remove the brake master cylinder reservoir filler cap assembly.

7. Bleed the brake line.(*3)

(a) Remove the rear disc brake bleeder plug cap.

(b) Connect a vinyl tube to the rear disc brake bleeder plug.

(c) Add brake fluid to the reservoir until the fluid level is between the MAX and MIN lines on the brake fluid reservoir.(*a)

(d) Depress the brake pedal several times with approximately 1 second between each depression, and then loosen the bleeder plug with the pedal depressed.(*b)

(e) When brake fluid stops coming out, tighten the bleeder plug and then release the brake pedal for 1 second or more.(*c)

HINT:

When the brake pedal is released, the piston inside the master cylinder may take longer than the brake pedal to return to its original position. Therefore, make sure to wait for 1 second or more between each depression of the brake pedal.


(f) Repeat steps (*a) through (*c) until there are no signs of air in the brake fluid.

8. Repeat steps (*a) through (*c) until there are no signs of air in the brake fluid.

NOTICE:

If there is still air in the system after performing steps (*1) through (*3) 3 times, repeat the steps (*1) through (*3) until the air has been bled.


9. Tighten the rear disc brake bleeder plug completely.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)

10. Install the rear disc brake bleeder plug cap to the rear disc brake bleeder plug.

11. Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with 2 new bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)

12. Inspect for brake fluid leaks.

13. Adjust the brake fluid level in the reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>ON-VEHICLE INSPECTION

14. Install the brake master cylinder reservoir filler cap assembly.

15. Install the center No. 1 cowl top ventilator louver.

Click hereGeneral>MAINTENANCE>BRAKE FLUID (for HV Model)>REPLACEMENT

16. Turn the ignition switch off.

17. Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model)>DTC CHECK / CLEAR



Hide 20.INSTALL REAR WHEEL

Hide 23. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (for HV Model)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART