Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for HV Model LHD) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480876 BRAKE BOOSTER(for HV Model LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for HV Model LHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C461007N01
2.083,0.698 2.417,0.698 false 5.667,1.5 5.667,1.167 false 2.229,2.115 2.563,2.115 false 2.115,3.563 2.448,3.563 false 1.833,4.375 2.417,4.375 false 6.469,0.208 6.802,0.208 false 2.5,0.521 2.781,0.875 0.281,0.354 18 false 1 6.25,0.104 6.531,0.458 0.281,0.354 18 false 2 1.635,4.219 1.917,4.573 0.281,0.354 18 false 3 1.938,3.469 2.25,3.667 0.313,0.198 10 false *1 2.031,2 2.344,2.198 0.313,0.198 10 false *1 5.771,1.5 6.052,1.854 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INVERTER WITH CONVERTER ASSEMBLY G9200 - - -
2 DRAIN BRAKE FLUID - - (Click here) -
3 ENGINE ROOM MAIN WIRE 82111 (Click here) - -

*1 CONNECTOR - -

C461008N01
2.208,0.917 2.667,0.917 false 6.25,2.854 6.583,2.854 false 1.927,2.677 2.26,2.677 false 2.958,0.813 3.24,1.167 0.281,0.354 18 false 6 2.333,2.521 2.615,2.875 0.281,0.354 18 false 5 6.656,2.677 6.938,3.031 0.281,0.354 18 false 4 6.208,3.208 6.521,3.406 0.313,0.198 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

4 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
5 COLUMN HOLE COVER SILENCER SHEET 45259A - - -
6 NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY 45260 (Click here) - -

C461009N01
3.677,2.323 4.01,2.323 false 2.521,1.875 2.854,1.875 false 3.313,3.594 3.313,3.26 false 2.563,3.26 2.729,3.26 2.729,3.26 2.813,2.927 false 1.354,3.573 1.354,3.073 false 5.01,3.833 5.344,3.833 false 6.313,2.792 6.646,2.792 false 5.76,3.417 6.094,3.417 false 0.667,0.865 0.833,0.865 0.833,0.865 0.833,0.948 false 0.469,0.948 1.052,0.948 true 1.5,0.75 1.781,1.104 0.281,0.354 18 false 9 2.938,1.708 3.385,2.042 0.448,0.333 18 false 11 4.229,2.146 4.677,2.479 0.448,0.333 18 false 13 4.083,2.219 4.24,2.417 0.156,0.198 10 false ● 2.417,3.156 2.573,3.354 0.156,0.198 10 false ● 3.208,3.635 3.656,3.969 0.448,0.333 18 false 10 6.708,2.698 6.865,2.896 0.156,0.198 10 false ● 6.865,2.635 7.156,2.979 0.292,0.344 18 false 7 6.417,3.271 6.708,3.615 0.292,0.344 18 false 9 4.813,3.698 5.104,4.042 0.292,0.344 18 false 8 4.688,3.771 4.844,3.969 0.156,0.198 10 false ● 4.219,2.771 4.583,3.031 0.365,0.26 10 false x4 1.375,3.5 1.823,3.833 0.448,0.333 18 false 12

Procedure Part Name Code
Z101186

Z101188

Z101187

7 NO. 6 BRAKE TUBE CLAMP 47371B - - -
8 NO. 2 BRAKE TUBE CLAMP 47372 - - -
9 BRAKE LINE - (Click here) - -
10 BRAKE PEDAL RETURN SPRING 47101A - - -
11 PUSH ROD PIN 47264A - - -
12 BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 47210L (Click here) - -
13 BRAKE BOOSTER GASKET 44785C - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Electric brake booster (brake booster with master cylinder assembly)
1.

Bleed air

2.

Perform "Reset Memory"

3.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)

NOTICE:
·

When disassembling the brake pedal support assembly, do not loosen the breakaway bolt at the time of collisions.

·

If the breakaway bolt at the time of collisions is loosened, replace with a new brake pedal support assembly.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide G9200 1.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 2.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 82111 3.SEPARATE ENGINE ROOM MAIN WIRE

a.
C461000C01
0.281,0.063 0.823,0.406 0.542,0.344 18 false i, ii 3.833,0.073 4.375,0.417 0.542,0.344 18 false iii 3.552,3.083 4.094,3.427 0.542,0.344 18 false v, vi 0.438,3.052 0.979,3.396 0.542,0.344 18 false iv
V113147

Push in this direction
V113148

Disconnect the connector
V100137

Release the lock lever - -


i.

Disconnect the connector.


ii.

Disengage the clamp.


iii.

Disconnect the connector from the brake master cylinder reservoir assembly.


iv.

Release the lock lever and disconnect the connector from the booster with master cylinder assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



v.

Remove the bolt to separate the engine room main wire.


vi.

Disengage the clamp.



Hide 55606 4.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 45259A 5.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 6.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Z101186

Click here(Click here)

Hide 47371B 7.REMOVE NO. 6 BRAKE TUBE CLAMP

a.
C461001


Hide 47372 8.REMOVE NO. 2 BRAKE TUBE CLAMP

a.
C461002


Hide 9.DISCONNECT BRAKE LINE

Z101186

NOTICE:
·

Do not damage or deform the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




a.
C461003N01
0.365,0.052 0.646,0.406 0.281,0.354 18 false i 3.854,0.042 4.135,0.396 0.281,0.354 18 false ii 1.958,2.042 2.24,2.396 0.281,0.354 18 false iii

i.

Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder sub-assembly.


ii.

Using a union nut wrench, disconnect the brake line from the front No. 2 brake tube way.


iii.

Using a union nut wrench, disconnect the brake line from the front flexible hose.



Hide 47101A 10.REMOVE BRAKE PEDAL RETURN SPRING

Hide 47210L 12.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C461004N01
1.802,0.042 2.083,0.396 0.281,0.354 18 false i

i.

Remove the 4 nuts and brake booster with master cylinder assembly.

NOTICE:
·
C461005C01
1.365,1.865 1.698,1.865 false 2.917,0.99 2.917,0.656 false 2.552,0.531 2.635,0.198 2.635,0.198 2.802,0.198 false 1.719,0.396 1.635,0.146 1.635,0.146 1.469,0.146 false 0.719,1.083 0.646,1.406 0.646,1.406 0.479,1.406 false 1.188,1.771 1.5,1.927 0.313,0.156 10 false *a 1.281,0.052 1.594,0.208 0.313,0.156 10 false *b 2.854,0.115 3.167,0.271 0.313,0.156 10 false *c 2.854,1.021 3.167,1.177 0.313,0.156 10 false *d 0.302,1.292 0.615,1.448 0.313,0.156 10 false *e
*a ECU Connector
*b Connector
*c Boot
*d Brake Master Cylinder Push Rod Clevis
*e Brake Master Cylinder Reservoir Assembly


Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.

·

Do not kink or damage the brake lines.

·

Be careful not to allow any brake fluid to enter the connector.





Hide 44785C 13.REMOVE BRAKE BOOSTER GASKET

a.
C461006