Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for HV Model TMMF Made RHD) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480878 BRAKE BOOSTER(for HV Model TMMF Made RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for HV Model TMMF Made RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C456276N02
3.073,0.938 3.406,0.938 false 4.156,1.302 4.49,1.302 false 5.292,1.917 5.625,1.917 false 4.521,3.365 4.854,3.365 false 6.396,0.323 6.729,0.323 false 6.375,0.75 6.708,0.75 false 6.406,1.115 6.74,1.115 false 6.167,0.146 6.448,0.5 0.281,0.354 18 false 1 6.156,0.563 6.438,0.917 0.281,0.354 18 false 2 6.188,0.958 6.469,1.313 0.281,0.354 18 false 7 5.75,1.75 6.031,2.104 0.281,0.354 18 false 5 4.583,1.083 4.865,1.438 0.281,0.354 18 false 4 3.5,0.729 3.781,1.083 0.281,0.354 18 false 3 4.969,3.167 5.25,3.521 0.281,0.354 18 false 6 2.271,1.333 2.729,1.531 0.458,0.198 10 false x12

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 WINDSHIELD WIPER MOTOR AND LINK - - - -
4 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
5 WATER GUARD PLATE LH 55735A - - -
6 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
7 DRAIN BRAKE FLUID - - (Click here) -

C461022N01
3.135,0.615 3.469,0.615 false 4.708,3.5 5.042,3.5 false 0.542,2.917 1.042,2.917 false 0.646,2.031 0.979,2.031 false 3.542,0.5 3.854,0.698 0.313,0.198 10 false *1 0.469,1.917 0.781,2.115 0.313,0.198 10 false *2 0.354,2.771 0.635,3.125 0.281,0.354 18 false 8 4.521,3.344 4.802,3.698 0.281,0.354 18 false 9

Procedure Part Name Code
Z101186

Z101188

Z101187

8 SEPARATE ENGINE ROOM MAIN WIRE 82111 (Click here) - -
9 DASH PANEL HEAT INSULATOR 55225C - - -

*1 NO. 2 ENGINE ROOM WIRE *2 CONNECTOR

C461023N02
4.813,1 5.146,1 false 2.698,0.26 3.063,0.156 3.063,0.156 3.229,0.156 false 5.177,2.063 5.677,2.063 false 4.927,3.375 4.927,3.042 4.927,3.042 5.76,3.042 false 5.042,3.417 5.042,3.052 true 1.469,4.917 1.802,4.917 false 3.396,3.885 3.729,3.885 false 2.417,3.5 2.75,3.5 false 4.198,1.865 4.198,2.198 false 2.771,2.094 3.271,2.094 false 3.302,0.031 3.76,0.396 0.458,0.365 18 false 15 5.375,0.885 5.792,1.229 0.417,0.344 18 false 17 5.24,0.917 5.396,1.115 0.156,0.198 10 false ● 4.177,2.219 4.333,2.417 0.156,0.198 10 false ● 5.635,1.458 5.885,1.656 0.25,0.198 10 false x4 4.313,5.167 4.563,5.365 0.25,0.198 10 false x2 5.75,1.896 6.167,2.24 0.417,0.344 18 false 14 6.083,2.938 6.531,3.302 0.448,0.365 18 false 12 3.542,1.969 3.969,2.344 0.427,0.375 18 false 16 2.094,3.344 2.531,3.708 0.438,0.365 18 false 10 3.115,3.74 3.542,4.094 0.427,0.354 18 false 11 1.115,4.771 1.49,5.115 0.375,0.344 18 false 13 1.979,3.396 2.135,3.594 0.156,0.198 10 false ● 2.979,3.781 3.135,3.979 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

10 NO. 3 BRAKE TUBE CLAMP 47373B - - -
11 NO. 1 BRAKE TUBE CLAMP 47371A - - -
12 BRAKE LINE - (Click here) - -
13 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
14 BRAKE PEDAL RETURN SPRING 47101A - - -
15 PUSH ROD PIN 47264A - - -
16 BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 47210L (Click here) - -
17 BRAKE BOOSTER GASKET 44785C - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
Electric brake booster (brake booster with master cylinder assembly)
1.

Bleed air

2.

Perform "Reset Memory"

3.

Perform calibration


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)

NOTICE:
·

When disassembling the brake pedal support assembly, do not loosen the breakaway bolt at the time of collisions.

·

If the breakaway bolt at the time of collisions is loosened, replace with a new brake pedal support assembly.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55815E 4.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55701J 6.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 7.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 82111 8.SEPARATE ENGINE ROOM MAIN WIRE

a.
C461014C01
0.292,0.042 0.573,0.396 0.281,0.354 18 false i 3.74,0.094 4.281,0.458 0.542,0.365 18 false ii, iii 0.198,2.115 0.479,2.469 0.281,0.354 18 false iv 3.969,2.542 4.25,2.896 0.281,0.354 18 false v
V113147

Push in this direction
V113148

Disconnect the connector
V100137

Release the lock lever - -


i.

Disconnect the connector from the No. 2 engine room wire.


ii.

Disconnect the connector from the brake booster with master cylinder assembly.


iii.

Disengage the clamp to remove the No. 2 engine room wire from the brake booster with master cylinder assembly.


iv.

Disconnect the connector from the brake master cylinder reservoir assembly.


v.

Release the lock lever and disconnect the connector from the brake booster with master cylinder assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.




Hide 55225C 9.SEPARATE DASH PANEL HEAT INSULATOR

a.
C461015


Hide 47373B 10.REMOVE NO. 3 BRAKE TUBE CLAMP

a.
C461017


Hide 47371A 11.REMOVE NO. 1 BRAKE TUBE CLAMP

a.
C461018


Hide 12.REMOVE BRAKE LINE

Z101186

NOTICE:
·

Do not damage or deform the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




a.
C461016N01
0.396,0.042 0.677,0.396 0.281,0.354 18 false i 3.896,0.021 4.177,0.375 0.281,0.354 18 false ii

i.

Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder sub-assembly.


ii.

Using a union nut wrench, disconnect the 2 brake lines from the brake actuator assembly.



Hide 55606 13.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 47101A 14.REMOVE BRAKE PEDAL RETURN SPRING

Hide 47210L 16.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C461019N01
1.771,0.021 2.052,0.375 0.281,0.354 18 false i

i.

Remove the 4 nuts and brake booster with master cylinder assembly.

NOTICE:
·
C461020C01
2,1.469 2.313,1.938 2.313,1.938 2.479,1.938 true 2.542,0.635 2.656,0.229 2.656,0.229 2.823,0.229 false 0.427,1.323 0.594,1.323 0.594,1.323 0.677,0.958 false 1.365,0.146 1.531,0.146 1.531,0.146 1.698,0.479 false 2.885,1.094 2.885,0.76 false 2.552,1.833 2.865,1.99 0.313,0.156 10 false *a 1.167,0.042 1.479,0.198 0.313,0.156 10 false *b 2.885,0.135 3.198,0.292 0.313,0.156 10 false *c 2.813,1.135 3.125,1.292 0.313,0.156 10 false *d 0.25,1.219 0.563,1.375 0.313,0.156 10 false *e
*a ECU Connector
*b Connector
*c Boot
*d Brake Master Cylinder Push Rod Clevis
*e Brake Master Cylinder Reservoir Assembly


Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.

·

Do not kink or damage the brake lines.

·

Be careful not to allow any brake fluid to enter the connector.





Hide 44785C 17.REMOVE BRAKE BOOSTER GASKET

a.
C461021