Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for HV Model TMMF Made RHD) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480878 BRAKE BOOSTER(for HV Model TMMF Made RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for HV Model TMMF Made RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C461026N02
6.021,1.313 6.771,1.479 0.75,0.167 5.979,1.271 6.813,1.521 0.833,0.25 1.333,2.729 2.333,3.063 1,0.333 1.292,2.688 2.375,3.104 1.083,0.417 4.625,4.813 5.708,5.229 1.083,0.417 4.667,4.854 5.667,5.188 1,0.333 4.813,1 5.146,1 false 2.708,0.396 3.083,0.146 3.083,0.146 3.25,0.146 false 5.688,1.385 6.021,1.385 false 5.177,2.063 5.677,2.063 false 4.927,3.375 4.927,3.042 4.927,3.042 5.76,3.042 false 5.042,3.417 5.042,3.052 true 5.677,5.021 6.26,5.021 6.26,5.021 6.26,4.771 false 6.104,5.021 6.104,4.688 true 1.469,4.917 1.802,4.917 false 3.396,3.885 3.729,3.885 false 2.417,3.5 2.75,3.5 false 2.333,2.885 2.917,2.885 false 2.76,2.885 2.76,2.969 2.76,2.969 3.094,2.969 false 4.198,1.865 4.198,2.198 false 2.771,2.094 3.271,2.094 false 3.552,0.042 3.833,0.396 0.281,0.354 18 false 3 5.375,0.885 5.656,1.24 0.281,0.354 18 false 1 5.24,0.917 5.396,1.115 0.156,0.198 10 false ● 4.177,2.219 4.333,2.417 0.156,0.198 10 false ● 5.583,1.427 5.833,1.625 0.25,0.198 10 false x4 4.313,5.167 4.563,5.365 0.25,0.198 10 false x2 6.073,1.302 6.906,1.458 0.833,0.156 8 false 12.7 (130, 9) 6.031,1.896 6.313,2.25 0.281,0.354 18 false 4 6.083,2.938 6.365,3.292 0.281,0.354 18 false 6 3.542,1.969 3.823,2.323 0.281,0.354 18 false 2 1.448,2.75 2.281,2.906 0.833,0.156 8 false 19.5 (199, 14) 1.448,2.906 2.365,3.063 0.917,0.156 8 false 17.4 (177, 13)* 2.229,3.333 2.51,3.688 0.281,0.354 18 false 8 3.208,3.74 3.49,4.094 0.281,0.354 18 false 7 1.26,4.781 1.542,5.135 0.281,0.354 18 false 5 2.094,3.396 2.25,3.594 0.156,0.198 10 false ● 3.052,3.792 3.208,3.99 0.156,0.198 10 false ● 4.75,4.875 5.583,5.031 0.833,0.156 8 false 19.5 (199, 14) 4.76,5.021 5.677,5.177 0.917,0.156 8 false 17.4 (177, 13)*

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE BOOSTER GASKET 44785C - - -
2 BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 47210L (Click here) - -
3 PUSH ROD PIN 47264A (Click here) - -
4 BRAKE PEDAL RETURN SPRING 47101A (Click here) - -
5 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
6 INSTALL BRAKE LINE - (Click here) - -
7 NO. 1 BRAKE TUBE CLAMP 47371A - - -
8 NO. 3 BRAKE TUBE CLAMP 47373B - - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) * For use with a union nut wrench
● Non-reusable part
V100135

Lithium soap base glycol grease

C461022N02
4.094,2.49 5.094,2.656 1,0.167 3.135,0.615 3.469,0.615 false 4.708,3.5 5.042,3.5 false 0.688,2.917 1.021,2.917 false 0.646,2.031 0.979,2.031 false 5.104,2.573 5.271,2.573 5.271,2.573 5.438,2.823 false 3.542,0.5 3.854,0.698 0.313,0.198 10 false *1 0.469,1.917 0.781,2.115 0.313,0.198 10 false *2 0.323,2.75 0.781,3.104 0.458,0.354 18 false 10 4.521,3.344 4.802,3.698 0.281,0.354 18 false 9 4.135,2.5 5.219,2.667 1.083,0.167 8 false 5.0 (51, 44 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

9 DASH PANEL HEAT INSULATOR 55225C - - -
10 ENGINE ROOM MAIN WIRE 82111 (Click here) - -

*1 NO. 2 ENGINE ROOM WIRE *2 CONNECTOR
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

C460849N02
1.021,1.417 1.771,1.583 0.75,0.167 3.073,0.938 3.406,0.938 false 4.156,1.302 4.49,1.302 false 5.292,1.917 5.625,1.917 false 4.521,3.365 4.854,3.365 false 6.396,0.323 6.729,0.323 false 6.375,0.75 6.708,0.75 false 6.323,1.115 6.656,1.115 false 1.771,1.5 2.104,1.5 false 5.177,0.167 6.49,0.521 1.313,0.354 18 false 17, 18, 20 6.021,0.573 6.396,0.927 0.375,0.354 18 false 15 5.573,0.969 6.396,1.344 0.823,0.375 18 false 16, 19 5.75,1.75 6.302,2.104 0.552,0.354 18 false 12 4.583,1.083 5.177,1.438 0.594,0.354 18 false 13 3.5,0.729 3.958,1.073 0.458,0.344 18 false 14 4.979,3.167 5.438,3.531 0.458,0.365 18 false 11 2.271,1.333 2.729,1.531 0.458,0.198 10 false x12 1.104,1.427 1.865,1.688 0.76,0.26 8 false 12 (122, 9)

Procedure Part Name Code
Z101186

Z101188

Z101187

11 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -
12 WATER GUARD PLATE LH 55735A - - -
13 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
14 WINDSHIELD WIPER MOTOR AND LINK - - - -
15 CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
16 UPDATE ECU SECURITY KEY - - - (Click here)
17 BLEED BRAKE LINE - (Click here) - -
18 INSPECT AND ADJUST BRAKE PEDAL - (Click here) - -
19 PERFORM INITIALIZATION AND CALIBRATION - - - (Click here)
20 CHECK AND CLEAR DTCS - (Click here) - -

V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

CAUTION / NOTICE / HINT

NOTICE:

After performing the update ECU security key procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 44785C 1.INSTALL BRAKE BOOSTER GASKET

Hide 47210L 2.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C461019N03
1.771,0.021 2.052,0.375 0.281,0.354 18 false i 2.958,1.313 3.094,1.49 0.135,0.177 10 true 1 4.167,0.365 4.302,0.542 0.135,0.177 10 true 2 2.927,0.365 3.063,0.542 0.135,0.177 10 true 3 4.146,1.313 4.281,1.49 0.135,0.177 10 true 4

i.

Install the brake booster with master cylinder assembly with the 4 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Tighten the nuts in the order shown in the illustration.

·
C461020C01
2,1.469 2.313,1.938 2.313,1.938 2.479,1.938 true 2.542,0.635 2.656,0.229 2.656,0.229 2.823,0.229 false 0.427,1.323 0.594,1.323 0.594,1.323 0.677,0.958 false 1.365,0.146 1.531,0.146 1.531,0.146 1.698,0.479 false 2.885,1.094 2.885,0.76 false 2.552,1.833 2.865,1.99 0.313,0.156 10 false *a 1.167,0.042 1.479,0.198 0.313,0.156 10 false *b 2.885,0.135 3.198,0.292 0.313,0.156 10 false *c 2.813,1.135 3.125,1.292 0.313,0.156 10 false *d 0.25,1.219 0.563,1.375 0.313,0.156 10 false *e
*a ECU Connector
*b Connector
*c Boot
*d Brake Master Cylinder Push Rod Clevis
*e Brake Master Cylinder Reservoir Assembly


Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.

·

Do not kink or damage the brake lines.

·

Be careful not to allow brake fluid to enter the connector.

·

If installing a new brake booster with master cylinder assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with master cylinder is filled with brake fluid.





Hide 47264A 3.INSTALL PUSH ROD PIN

Z101186

Click here(Click here)

Hide 47101A 4.INSTALL BRAKE PEDAL RETURN SPRING

Z101186

Click here(Click here)

Hide 55606 5.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 6.INSTALL BRAKE LINE

Z101186

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




a.
C461024C01
3.635,2.438 3.948,2.594 0.313,0.156 10 false *a 0.427,0 0.583,0.292 0.156,0.292 18 false i 3.885,0.01 4.125,0.313 0.24,0.302 18 false ii
*a Torque Wrench Fulcrum Length - -


i.

Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




ii.

Using a union nut wrench, connect the 2 brake lines to the brake actuator assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)





Hide 47371A 7.INSTALL NO. 1 BRAKE TUBE CLAMP

Hide 47373B 8.INSTALL NO. 3 BRAKE TUBE CLAMP

Hide 55225C 9.INSTALL DASH PANEL HEAT INSULATOR

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

Hide 82111 10.INSTALL ENGINE ROOM MAIN WIRE

a.
C461025C01
0.385,0.042 0.667,0.396 0.281,0.354 18 false i 3.948,0.031 4.229,0.385 0.281,0.354 18 false ii 3.906,2 4.188,2.354 0.281,0.354 18 false v 0.219,2.031 0.781,2.313 0.563,0.281 14 false iii, iv
V113147

Connect the connector
V113148

Lock the lock lever


i.

Connect the connector to the brake booster with master cylinder assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.




ii.

Connect the connector to the brake master cylinder reservoir assembly.


iii.

Engage the clamp to install the No. 2 engine room wire to the brake booster with master cylinder assembly.


iv.

Connect the connector to the brake booster with master cylinder assembly.


v.

Connect the connector to the No. 2 engine room wire.



Hide 55701J 11.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55735A 12.INSTALL WATER GUARD PLATE LH

Hide 55815E 13.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 14.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 15.CONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 18.INSPECT AND ADJUST BRAKE PEDAL