| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | FRONT DISC BRAKE DUST COVER | 47782 | - | - | - |
| 2 | FRONT AXLE HUB SUB-ASSEMBLY | 43502C | ( )
|
- | - |
| *1 | STEERING KNUCKLE | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | - | - |
| *A | for HV Model TMC Made | *B | for TMMF Made |
| *1 | FRONT FLEXIBLE HOSE | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
|
Toyota body grease W |
|
Do not apply lubricants to the threaded parts |
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
47782
1.INSTALL FRONT DISC BRAKE DUST COVER
43502C
2.INSTALL FRONT AXLE HUB SUB-ASSEMBLY
Secure the steering knuckle between aluminum plates in a vise.
Do not overtighten the vise.
Install the front axle hub sub-assembly and front disc brake dust cover to the steering knuckle with the 3 bolts.
Be careful not to damage the speed sensor rotor or contact surfaces.
Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.
3.INSTALL FRONT AXLE ASSEMBLY
|
Toyota Body Grease W | - | - |
Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz.) of Toyota Body Grease W to each of the 4 areas shown in the illustration.
Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.
Do not apply lubricants to the steering knuckle and shock absorber contact surfaces.
When installing the nuts, keep the bolts from rotating.
43420
4.CONNECT FRONT DRIVE SHAFT ASSEMBLY
| *a | Matchmark | - | - |
Align the matchmarks on the front drive shaft assembly and front axle hub sub-assembly, and connect the front drive shaft assembly to the front axle assembly.
Do not push the front axle assembly towards the outside of the vehicle any further than necessary.
Check that there is no foreign matter on the speed sensor rotor or contact surfaces.
Do not damage the front drive shaft outboard joint boot.
Do not damage the front disc brake dust cover.
Do not damage the speed sensor rotor.
48069
5.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY
43502H
10.INSTALL FRONT AXLE SHAFT NUT
Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.
Be sure to perform this work even when using a new front drive shaft assembly.
Keep the threaded parts free of oil and foreign matter.
Using a 30 mm deep socket wrench, install the front axle shaft nut while applying the brakes.
Stake the front axle shaft nut after inspecting for looseness and runout in the following steps.
89543
17.INSTALL FRONT SPEED SENSOR
|
Hook | - | - |
Set the 2 hooks of the front speed sensor to the front shock absorber assembly.
Do not twist the front speed sensor when installing it.
Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt.
Do not twist the front flexible hose when installing it.
Install the front speed sensor to the steering knuckle with the bolt.
Prevent foreign matter from attaching to the front speed sensor tip.
Firmly insert the front speed sensor body into the steering knuckle before tightening the bolt.
After installing the front speed sensor to the steering knuckle, make sure that there is no clearance between the front speed sensor stay and steering knuckle. Also make sure that no foreign matter is stuck between the parts.
Do not twist the front speed sensor when installing it.
Engage the clamp.
Do not twist the front speed sensor when installing it.
43502H
18.STAKE FRONT AXLE SHAFT NUT
Using a chisel and hammer, stake the front axle shaft nut.
19.INSTALL FRONT WHEEL
20.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model TMC Made)
21.CHECK FOR SPEED SENSOR SIGNAL
for HV Model TMC Made:
for HV Model TMMF Made:
for Gasoline Model TMC Made:
for Gasoline Model TMMF Made:
22.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
23. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (for HV Model TMC Made)
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART