This is the troubleshooting procedure for situations where the engine does not restart after having been stopped by the stop and start system.
For information on stop and start control, refer to the system description.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>SYSTEM DESCRIPTION
PRECAUTIONS WHEN THE ENGINE STOP AND START ECU AND THE STARTER ASSEMBLY ARE REPLACED
When the engine stop and start ECU is replaced, it is necessary to read the number of starter operations before replacement and store this number in the new engine stop and start ECU after replacement, and to perform external backup boost converter (eco run vehicle converter assembly) existence learning. Moreover, initialization/learning of the air conditioning information and initialization/learning of the deceleration sensor zero point are also required.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
When the starter assembly is replaced, the number of starter operations stored in the engine stop and start ECU must be reset.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
When the starter assembly is replaced, "ST NO. 1 relay" must be also replaced.
Inspect the fuses for circuits related to this system before performing the following procedure.
PRECAUTIONS WHEN BATTERY IS DISCHARGED AFTER LEAVING VEHICLE FOR A LONG TIME
If the vehicle has not been used for a long time, the battery charge may be low and stop and start control operation may be prohibited. After recharging the battery until the charging current decreases to 5 A or below, if the integrated current value still does not increase to the threshold value*1 or above, initialize the integrated current value*2 and drive the vehicle approximately 5 to 40 minutes until stop and start control operates.
*1: For information about the integrated current threshold value, refer to the system description.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>SYSTEM DESCRIPTION
*2: Use the GTS to perform Integrated Current Value Initialization.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
PRECAUTIONS WHEN CONNECTING/DISCONNECTING CABLE TO/FROM NEGATIVE BATTERY TERMINAL
If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed. In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)
If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates. If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.
After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
If power is not supplied to the navigation system or audio and visual system when the ignition switch is turned to ON for the first time after the battery has been reconnected, DTC P323A19 will be stored. Perform either of the following operations:
Turn the ignition switch from ON to off twice.
After turning the ignition switch from ON to off, clear the DTCs.
IF THE ENGINE FAILS TO RESTART FROM IDLING STOP
When the engine fails to restart when stopped by stop and start control.
When the brake booster vacuum is insufficient.
When the vehicle speed is 3 km/h (2 mph) or more and the brake pedal is depressed*.
*: When the engine is not running.
When the engine fails to restart when stopped by stop and start control and the brake booster vacuum is insufficient, the brake actuator is activated to ensure the braking force. When the brake actuator is activated, sound and vibration may be generated. This is not due to malfunction of the stop and start system or the vehicle.
PRECAUTIONS FOR FOUR-WHEEL TOWING
Do not tow the vehicle with all 4 wheels on the ground.
Towing the vehicle with all 4 wheels on the ground may have a detrimental effect on the stop and start system, and could lead to damage.
If it is absolutely necessary to tow the vehicle with all 4 wheels on the ground, before towing first turn the ignition switch off. Then, turn the ignition switch to ON without starting the engine, and tow the vehicle.
PRECAUTIONS WHEN REPLACING ECM
When the ECM is replaced on a vehicle with a non-specified battery, it is necessary to perform battery type switching.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Enter the following menus.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Check vehicle control history.
| Result | Proceed to |
|---|---|
| Vehicle control history item Hood Open during Stop&Start (Engine Stall) stored | A |
| Vehicle control history item Hood Open during Stop&Start (Engine Stall) not stored | B |
A
B
Check the condition of the engine hood.
Check with the driver to confirm whether or not the engine hood was opened during stop and start control.
| Result | Proceed to |
|---|---|
| Engine hood was not opened during stop and start control | A |
| Engine hood was opened during stop and start control | B |
A
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>Engine Hood Courtesy Switch Circuit
B
Consult with the customer to determine if they performed operations that could result in an MT engine stall.
(ex.) Heavy load, frequent shifts, etc.
| Result | Proceed to |
|---|---|
| Driver operations that could cause engine stall were performed | A |
| None of the above conditions are met | B |
A
B
Following the instructions on the GTS screen, check for SFI system DTCs.
| Result | Proceed to | |
|---|---|---|
SFI system poor startability DTCs or RoBs not output, but SFI system poor startability related DTCs or RoBs are output.
|
A | |
| None of the above conditions are met | ·
After engine stalls, when starting engine using key or push switch operation, starter does not rotate. ·
Even after vehicle brought in, when starting engine using key or push switch operation, starter does not rotate. |
B |
·
When restarting engine from idling stop, starter did not rotate. ·
Even after vehicle brought in, when restarting engine from idling stop, starter does not rotate. |
C | |
·
When restarting engine from idling stop, starter rotated. ·
Unknown whether starter rotated (does not remember). |
D | |
A
Vehicle control history: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY
Diagnostic trouble code chart: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
B
C
Inspect battery
Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION
Inspect starter system
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>Starter Signal Circuit
D
Perform an operation check of the stop and start system to confirm what kind of operations result in the engine failing to restart after it has been stopped by the stop and start system.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK
| Result | Proceed to |
|---|---|
| While vehicle is stopped with the engine stopped by idling stop, the engine cannot restart when attempting to drive forward. | A |
| During idling stop, an operation that should restart the engine (brake off, shift operation, etc.) is performed, but there is no response to the start request (refer to Data List). | B |
A
B
Check the Data List items for countermeasures, and inspect the possible causes of engine start requests not being issued.
Depending on vehicle, some items may not be displayed.
| Countermeasures and Related Areas | Start Conditions |
|---|---|
When the engine is stopped by stop and start control, and the stop and start cancel switch is pressed but a start request is not issued, inspect the following components:
·
Stop and start cancel switch circuit |
Data List / Stop&Start Cancel Switch (ON: Stop and start system cancel switch (eco run cancel switch assembly) pressed |
| Countermeasures and Related Areas | Start Conditions |
|---|---|
When the engine is stopped by stop and start control, and a steering operation is performed but a start request is not issued, inspect the following components:
·
Steering sensor ·
Steering system ·
Engine stop and start ECU |
Data List / Steering Angle (Steering angle 25 deg or more since idling stop) |
| Countermeasures and Related Areas | Start Conditions |
|---|---|
When the engine is stopped by stop and start control, and a clutch operation is performed but a start request is not issued, inspect the following components:
·
Clutch upper switch ·
Engine stop and start ECU |
OFF: Clutch pedal depressed |
| Countermeasures and Related Areas | Start Conditions |
|---|---|
When the engine is stopped by stop and start control, and a clutch operation is performed but a start request is not issued, inspect the following components:
·
Clutch lower switch ·
Engine stop and start ECU |
ON: Clutch pedal is fully depressed all the way |
| Countermeasures and Related Areas | Start Conditions |
|---|---|
·
Check the heater and air conditioner system conditions. ·
When the heater and air conditioner system start conditions are fulfilled but a start request is not issued, inspect the following components: Heater and air conditioner system |
·
Air conditioning amplifier assembly internal counter ended ·
All of the following conditions apply: -
Blower Switch: ON condition -
Evaporator temperature is at or above the threshold value (threshold varies according to factors including temperature, humidity and sunlight amount levels) ·
Any of the following conditions apply: -
Blower Switch, A/C Switch: Changed from OFF to ON -
Defogger switch (front defroster): Turned from OFF to ON -
Changed from stop and start priority control to normal control |
| Countermeasures and Related Areas | Start Conditions |
|---|---|
When the engine is stopped by stop and start control, and the brake pedal is depressed further or the brakes are pumped repeatedly but a start request is not issued, inspect the following components:
·
Brake booster vacuum decreased ·
Vacuum sensor assembly or vacuum sensor assembly (atmospheric pressure sensor) ·
Brake booster assembly ·
Brake master pressure sensor (Brake system) ·
Engine stop and start ECU |
Data List / Brake Negative Pressure (Decreased vacuum inside brake booster (less than 37.5 kPa)(varies with brake master fluid pressure)) |
| Countermeasures and Related Areas | Start Conditions |
|---|---|
When the engine is stopped by stop and start control, and push start switch / key operation is performed but a start request is not issued, inspect the following components:
·
Smart key ECU assembly (Push start switch)/IG Switch (Mechanical key) ·
Push start switch ·
Engine stop and start ECU |
·
Starter is operating ·
When Data List / Starter Type (Tandem Starter): -
Data List / Starter Motor (ON: During cranking) |
Enter the following menus.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Check the vehicle control history.
Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.
As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
| Result | Proceed to |
|---|---|
| NO is displayed for Engine Start Fail in the vehicle control history | A |
| Yes is displayed for Engine Start Fail in the vehicle control history | B |
A
Vehicle control history: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY
Diagnostic trouble code chart: Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
B
Enter the following menus.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Select a vehicle control history item to display the data from the time of control.
Check the output data.
Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.
As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
| Result | Proceed to |
|---|---|
All recorded sections "Starter"*1 = OFF, and all recorded sections "Engine Speed (ECM)" = 0 rpm
|
A |
"Starter"*1 = ON for any sections, and all recorded sections "Engine Speed (ECM)" = 0 rpm
|
B |
"Engine Speed (ECM)" > 0 rpm for any sections
|
C |
*1: Starter Motor Status in the case of tandem starter
A
Click hereEngine / Hybrid System>STOP AND START>ENGINE STOP AND START ECU>REMOVAL
It is possible that there is a malfunction of the starter drive circuit inside the stop and start ECU.
B
C
Enter the following menus.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Check the vehicle control history item "Engine Starting Time".
Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.
As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
| Result | Proceed to |
|---|---|
"Cranking Time" is 1.5 seconds or more
|
A |
"Cranking Time" is less than 1.5 seconds
|
B |
A
B
Disconnect the A67 engine stop and start ECU connector.
Turn the ignition switch to ON.
Turn off any electrical loads.
Measure the resistance according to the value(s) in the table below.
11 V or higher
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A67)Location & Routingewd_type=routing;type=c;code=A67 Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECUewd_type=component;type=c;code=A67;pinno=1 |
||
| A67-1 (+B) - Body ground | Ignition switch ON | 11 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Check the voltage of the auxiliary battery.
Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.
As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
Depending on RoB detection timing, the minimum voltage from the previous startup will be stored for the Minimum Voltage (Cranking) and the Minimum Voltage (Starter Solenoid Engagement). For the battery condition at the start of the current driving cycle, see Battery Voltage.
When the value is 20 V, the value is being calculated.
| Result | Proceed to |
|---|---|
| Auxiliary battery voltage is 8.92 V or more | A |
| Auxiliary battery voltage is less than 8.92 V | B |
A
B
Measure the voltage of the auxiliary battery.
11 to 14 V
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Select a vehicle control history item to display the "Cranking Time" and "Starter OFF Permission History (ECM)" data from the time of control.
Check the output data.
Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.
As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
| Result | Proceed to | |
|---|---|---|
| "Cranking Time" is less than 1.5 seconds | "Starter OFF Permission History (ECM)" is ON
|
A |
"Starter OFF Permission History (ECM)" is OFF
|
B | |
"Cranking Time" is 1.5 seconds or more
|
- | C |
A
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>Engine Difficult to Start
Check whether the speed value of the EFI ECU is not a higher value than the original NE.
B
C
Enter the following menus.
| Tester Display |
|---|
| Engine Speed (ECM) |
| Engine Speed |
Compare the Data List items displayed on the GTS.
| Result | Proceed to |
|---|---|
| Engine Speed > Engine Speed (ECM) + 300 rpm | A |
| None of the above conditions are met | B |
A
B
Enter the following menus.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Select a vehicle control history item to display the data from the time of control.
Check the data points in the data that was output.
Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.
As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
| Result | Proceed to |
|---|---|
| For each and all of the data points, Engine Speed > Engine Speed (ECM) + 300 rpm | A |
| None of the above conditions are met | B |
A
B
| *a | Component with harness connected
(Engine Stop and Start ECU) |
- | - |
Enter the following menus.
| Tester Display |
|---|
| Starter Motor Drive Magnet Switch(Hood Close) |
Measure the voltage according to the value(s) in the table below.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A67)Location & Routingewd_type=routing;type=c;code=A67 Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECUewd_type=component;type=c;code=A67;pinno=21,6 |
||
| A67-21 (STA) - A67-6 (DGND) | Performing Active Test, while cranking. | 6 to 14 V |
| A67-21 (STA) - A67-6 (DGND) | Performing Active Test, while cranking. | 6 to 14 V |
Using an oscilloscope, measure the waveform immediately after starting.
| Item | Content |
|---|---|
| Tester Connection | A67-21 (STA) ←→ A67-6 (DGND) |
| Tool Setting | 10 V/DIV, 200 ms./DIV |
| Condition | During cranking |
Voltage and waveform both normal
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Engine Stop and Start ECU) |
- | - |
Enter the following menus.
| Tester Display |
|---|
| Starter Motor Drive Magnet Switch(Hood Close) |
Measure the voltage according to the value(s) in the table below.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A67)Location & Routingewd_type=routing;type=c;code=A67 Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECUewd_type=component;type=c;code=A67;pinno=21,6 |
||
| A67-21 (STA) - A67-6 (DGND) | Performing Active Test, while cranking. | 6 to 14 V |
| A67-21 (STA) - A67-6 (DGND) | Performing Active Test, while cranking. | 6 to 14 V |
Using an oscilloscope, measure the waveform immediately after starting.
| Item | Content |
|---|---|
| Tester Connection | A67-21 (STA) ←→ A67-6 (DGND) |
| Tool Setting | 10 V/DIV, 200 ms./DIV |
| Condition | During cranking |
Voltage and waveform both normal
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Enter the following menus: Powertrain / Stop and Start / Utility / Vehicle Control History (RoB).
Select a vehicle control history item to display the data from the time of control.
Check the output data.
Checking the freeze frame data allows the vehicle conditions at the time of detection to be confirmed.
As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save the Vehicle Control History data before performing any inspections.
| Result | Proceed to |
|---|---|
| When Starter Motor is ON, there is even 1 point at which Engine Speed < 300 rpm | A |
| None of the above conditions are met | B |
A
B
Check how long it took the engine to stall after turning the starter off.
| Result | Proceed to |
|---|---|
After starter turned off, engine immediately stalls.
|
A |
| After starter turned off, engine stalls after a time. | B |
A
B