Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483557 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  Brake Warning Light Remains ON  


DESCRIPTION

This procedure is for troubleshooting when the brake system warning light (red indicator) remains on but no DTCs are output.

The skid control ECU (brake actuator assembly) controls the brake system warning light (red indicator) in the combination meter assembly via CAN communication.

WIRING DIAGRAM

C463941E01
5.667,0.469 5.979,0.667 0.313,0.198 10 false 19 5.729,1.083 6.042,1.281 0.313,0.198 10 false 5 5.969,0.688 6.583,0.885 0.615,0.198 10 false CANL 5.969,1.281 6.583,1.479 0.615,0.198 10 false CANH 5.583,4.573 6.042,4.771 0.458,0.198 10 false A39 5.573,4.719 7.104,5.167 1.531,0.448 10 false Skid Control ECU (Brake Actuator Assembly) 0.75,0.677 1.365,0.875 0.615,0.198 10 false CANL 0.719,1.292 1.333,1.49 0.615,0.198 10 false CANH 1.25,0.479 1.563,0.677 0.313,0.198 10 false 25 0.802,2.615 1.417,2.813 0.615,0.198 10 false VCM 0.885,4.25 1.5,4.448 0.615,0.198 10 false SW 1.271,1.073 1.583,1.271 0.313,0.198 10 false 9 1.25,2.51 1.563,2.708 0.313,0.198 10 false 32 1.25,4.156 1.563,4.354 0.313,0.198 10 false 16 1.906,2.594 2.219,2.792 0.313,0.198 10 false 2 3.156,2.594 3.469,2.792 0.313,0.198 10 false 1 1.583,3.115 2.042,3.313 0.458,0.198 10 false A29 1.604,4.927 2.063,5.125 0.458,0.198 10 false A102 1.604,5.094 4.104,5.615 2.5,0.521 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 1.583,3.271 4.01,3.625 2.427,0.354 10 false Vacuum Warning Switch Assembly 3.938,6.125 5.854,6.49 1.917,0.365 10 false : CAN Communication Line 0.083,5.938 2,6.354 1.917,0.417 10 false Combination Meter Assembly 1.833,4.26 2.146,4.458 0.313,0.198 10 false 1 3.771,4.271 4.083,4.469 0.313,0.198 10 false 2 1.26,4.365 1.719,4.563 0.458,0.198 10 false H7 1.25,2.719 1.708,2.917 0.458,0.198 10 false H7 1.25,1.281 1.708,1.479 0.458,0.198 10 false H6 1.25,0.688 1.708,0.885 0.458,0.198 10 false H6 2.104,2.594 2.417,2.792 0.313,0.198 10 false + 2.927,2.594 3.24,2.792 0.313,0.198 10 false E 3.542,4.25 3.854,4.448 0.313,0.198 10 false E 2.031,4.24 2.344,4.438 0.313,0.198 10 false +

CAUTION / NOTICE / HINT

NOTICE:
·

Before performing this procedure, depress the brake pedal and confirm that the stop lights illuminate.

·

After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY



PROCEDURE

1.PRE-CHECK
a.

Check that all of the following conditions required for the brake system warning light (red indicator) to turn off are met:

i.

The ABS warning light are not illuminated.

HINT:

If the ABS warning light remains illuminated, make sure that the conditions required for the ABS warning light to turn off are met.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>PROBLEM SYMPTOMS TABLE



ii.

The brake fluid level in the brake master cylinder reservoir assembly is not low.


iii.

The vacuum inside the brake booster decreases.

HINT:

When the vacuum inside the brake booster decreases, the brake system warning light (red indicator) comes on.




Result:
Proceed to
NEXT



NEXT

2.CHECK VEHICLE CONTROL HISTORY (RoB) (ELECTRONICALLY CONTROLLED BRAKE SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM)
2.CHECK VEHICLE CONTROL HISTORY (RoB) (ELECTRONICALLY CONTROLLED BRAKE SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM)
a.

Using the GTS, check for Vehicle Control History (RoB).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>VEHICLE CONTROL HISTORY (RoB)

Chassis > Brake/EPB > Utility
Tester Display
Vehicle Control History (RoB)
50005 435 55
HINT:

If vehicle control history (RoB) is stored when the electronically controlled brake system and electric parking brake system are suspended, the brake system warning light (red indicator) illuminates.



Result:
Result Proceed to
There is no vehicle control history (RoB) for when the electronically controlled brake system was suspended. A
There is vehicle control history (RoB) for when the electronically controlled brake system was suspended. B



A

3.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

B

PERFORM TROUBLESHOOTING AND REPAIR REGARDING VEHICLE CONTROL HISTORY (RoB)

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>VEHICLE CONTROL HISTORY (RoB)

NOTICE:

After performing troubleshooting and repair regarding vehicle control history (RoB), clear the vehicle control history (RoB).



3.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.
C230719C68
1.479,0.76 1.969,1.021 0.49,0.26 2,1.99 2.51,2.813 true 1.458,1.99 0.958,2.813 true 1.542,0.823 1.958,1.021 0.417,0.198 10 false A102 2.563,2.844 2.719,3.031 0.156,0.188 10 false + 0.844,2.865 1,3.052 0.156,0.188 10 false E 0.156,0.156 0.385,0.344 0.229,0.188 10 false *a
*a Component without harness connected
(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly))


Disconnect the A102 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.



e.

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A102)Location & Routing

Click Connector(A102)Engine Compartment>Engine Room Main Wire>Level Warning Switch (Brake Master Cylinder Reservoir Assembly)

A102-1 (+) - A102-2 (E) Switch off (float up) 1.9 to 2.1 kΩ
A102-1 (+) - A102-2 (E) Switch on (float down) Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the H7 combination meter assembly connector.


c.

Disconnect the A102 brake fluid level warning switch (brake master cylinder reservoir assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H7,A102)Location & Routing

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

Click Connector(A102)Engine Compartment>Engine Room Main Wire>Level Warning Switch (Brake Master Cylinder Reservoir Assembly)

H7-16 (SW) - A102-1 (+) Always Below 1 Ω
H7-16 (SW) or A102-1 (+) - Body ground Always 10 kΩ or higher
A102-2 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT VACUUM WARNING SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT VACUUM WARNING SWITCH ASSEMBLY

OK

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the H7 combination meter assembly connector.


c.

Disconnect the A29 vacuum warning switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H7,A29)Location & Routing

Click Connector(H7)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Meter Assembly

Click Connector(A29)Engine Compartment>Engine Room Main Wire>Vacuum Warning Switch Assembly

H7-32 (VCM) - A29-2 (+) Always Below 1 Ω
H7-32 (VCM) or A29-2 (+) - Body ground Always 10 kΩ or higher
A29-1 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display
Brake Warning
50004 409 107

b.

Check the combination meter assembly.

OK:

The brake system warning light (red indicator) turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

NG