| *A | for Front Pssenger Side | *B | for Driver Side |
|
MP grease | - | - |
| *A | for Driver Side | *B | for Front Pssenger Side |
| ● | Non-reusable part |
|
MP grease |
| *A | for TMMF Made | *B | for TMC Made |
| *C | for Type A | *D | for Type B |
| ● | Non-reusable part |
|
MP grease |
| ★ | Precoated part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front door removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the LH side and RH side.
The following procedure is for the RH side.
1. PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>REMOVAL
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
67492A
3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)
5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)
67656
6.REMOVE FRONT DOOR TRIM GARNISH
|
Remove in this Direction | - | - |
67602
7.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Using a screwdriver with its tip wrapped in protective tape, disengage the claw to open the front door inside handle bezel plug.
| *1 | Front Door Inside Locking Cable Assembly | *2 | Front Door Lock Remote Control Cable Assembly |
|
Place Hands Here |
|
Remove in this Direction |
Disengage the clips as shown in the illustration.
Disengage the front door trim board sub-assembly with the front door glass inner weatherstrip, front door vent seal and front door panel protector as shown in the illustration.
Disengage the guides to disconnect the front door inside locking cable assembly and front door lock remote control cable assembly to remove the front door trim board sub-assembly as shown in the illustration.
69206B
8.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
69284C
9.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
68172A
10.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP
|
Remove in this Direction | - | - |
Disengage the claws to remove the front door glass inner weatherstrip with the front vent seal and front door panel protector as shown in the illustration.
67838A
11.REMOVE FRONT DOOR VENT SEAL
67856B
12.REMOVE FRONT DOOR PANEL PROTECTOR
86160P
13.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
67832
14.REMOVE FRONT DOOR SERVICE HOLE COVER
Turn the 3 front door service hole cover clips 45° to remove it clips as shown in the illustration.
Disengage the guide and clamp to separate the wire harness from the front door service hole cover.
Disengage the clips to remove the front door service hole cover.
8983AA
15.REMOVE SIDE AIR BAG PRESSURE SENSOR
68102
16.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the hole plug.
| *A | for Driver Side | *B | for Front Passenger Side |
| *a | Bolt | - | - |
for Driver Side:
1. Connect the multiplex network master switch assembly.
for Front Passenger Side:
1. Connect the power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
| *A | for Driver Side | *B | for Front Passenger Side |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disconnect the cable from the negative (-) auxiliary battery terminal.
for Driver Side:
1. Disconnect the multiplex net work master switch assembly.
for Front Passenger Side:
1. Disconnect the power window regulator switch assembly.
Remove the 2 bolts.
Remove the front door glass sub-assembly as shown in the illustration.
Do not damage the front door glass sub-assembly.
69820
17.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
68151C
18.REMOVE FRONT DOOR GLASS RUN
67404F
19.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
|
Remove in this Direction | - | - |
67402F
20.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
69220
21.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
| *A | w/ Entry and Start System | - | - |
|
Remove in this Direction | - | - |
w/ Entry and Start System:
1. Disengage the claws.
2. Disconnect the connector.
Disengage the 2 claws and move the lever as shown in the illustration.
Remove the front door outside handle assembly as shown in the illustration.
22.REMOVE HOLE PLUG
23.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
Using a T30 "TORX" socket wrench, loosen the screw.
Remove the front door lock cylinder assembly.
69217D
24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the claws and guides to remove the front door outside handle cover.
69241H
25.REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD
69242H
26.REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD
69040A
27.REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY
69318C
28.REMOVE DOOR LOCK WIRING HARNESS SEAL
69202A
29.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
| *A | w/ Entry and Start System | - | - |
|
Remove in this Direction | - | - |
w/ Entry and Start System:
1. Disengage the clamp to separate the wire harness.
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the guides to remove the front door outside handle frame sub-assembly as shown in the illustration.
69312
30.REMOVE FRONT DOOR LOCK OPEN ROD
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
68210C
31.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>REMOVAL
32.REMOVE HOLE COVER
75074
33.REMOVE FRONT DOOR OUTSIDE LOWER MOULDING SUB-ASSEMBLY
67836J
34.REMOVE NO. 2 FRONT DOOR SERVICE HOLE SEAL
for TMC Made
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMC Made)>REMOVAL
for TMMF Made
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMMF Made)>REMOVAL
87940
35.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
for TMC Made
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMMF Made)>REMOVAL
for TMMF Made
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMC Made)>REMOVAL
67496C
36.REMOVE FRONT DOOR FRONT LOWER FRAME COVER UPPER
68620
37.REMOVE FRONT DOOR CHECK ASSEMBLY
67862
38.REMOVE FRONT DOOR WEATHERSTRIP
67001A
39.REMOVE FRONT DOOR PANEL CUSHION
75922M
40.REMOVE NO. 1 BLACK OUT TAPE
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Front Door)>REMOVAL
75926
41.REMOVE NO. 3 BLACK OUT TAPE
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Front Door)>REMOVAL
67837B
42.REMOVE FRONT DOOR DUST PROOF SEAL (for TMMF Made)
67837B
43.REMOVE FRONT DOOR DUST PROOF SEAL (for TMC Made)
for Type A:
Disengage the claws to remove the 3 front door dust proof seals.
When installing, install 2 dust proof seals inthe same way as for type B.
for Type B:
Disengage the claws to remove the 2 front door dust proof seals.