| *A | w/ Rear Power Window | - | - |
| *1 | WINDOW REGULATOR HANDLE PLATE | *2 | SHAFT SNAP RING |
| *A | w/ Rear Power Window | *B | w/o Rear Power Window |
| *1 | BUTYL TAPE | - | - |
| ● | Non-reusable part |
|
MP grease |
| *A | for TMMF Made | *B | for TMC Made |
| *C | for Type A | *D | for Type B |
| ● | Non-reusable part |
|
MP grease |
| ★ | Precoated part | - | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear door removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
Use the same procedure for the LH side and RH side.
The following procedure is for the RH side.
1. PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>REMOVAL
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
69260E
3.REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Rear Power Window)
Insert a clip remover with its shaft wrapped in protective tape between the window regulator handle plate and the rear door window regulator handle assembly.
Turn the rear door window regulator handle assembly with the clip remover inserted, as shown in the illustration.
Remove the shaft snap ring and the rear door window regulator handle assembly.
Remove the window regulator handle plate.
4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL
| *A | w/ Rear Power Window | - | - |
67604
5.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
|
Place Hands Here |
|
Remove in this Direction |
69206C
6.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
69284D
7.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
68174A
8.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP
|
Remove in this Direction | - | - |
Disengage the claws to remove the rear door glass inner weatherstrip with the rear door belt front seal as shown in the illustration.
68197A
9.REMOVE REAR DOOR BELT FRONT SEAL
68199
10.REMOVE REAR DOOR BELT REAR SEAL
86160B
11.REMOVE REAR SPEAKER ASSEMBLY
67842E
12.REMOVE REAR DOOR SERVICE HOLE COVER
Remove the rear door service hole cover.
Remove any remaining butyl tape from the rear door panel.
68152C
13.REMOVE REAR DOOR GLASS RUN
68104
14.REMOVE REAR DOOR GLASS SUB-ASSEMBLY
w/ Power Window:
Connect the rear power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the rear door glass sub-assembly so that the door glass bolts can be seen.
w/ Power Window:
|
Remove in this Direction | - | - |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the rear power window regulator switch assembly.
Remove the 2 bolts.
Remove the rear door glass sub-assembly as shown in the illustration.
Do not damage the front door glass subassembly.
w/o Power Window:
Install the rear door window regulator handle assembly.
Move the rear door glass sub-assembly so that the door glass bolt holes can be seen.
Remove the rear door window regulator handle assembly.
Remove the 2 bolts.
Remove the rear door glass sub-assembly as shown in the illustration.
Do not damage the front door glass subassembly.
68012
15.REMOVE REAR DOOR QUARTER WINDOW GLASS SUB-ASSEMBLY
|
Remove in this Direction | - | - |
67447C
16.REMOVE REAR DOOR WINDOW GUIDE PLATE LOWER
69840A
17.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY (w/ Rear Power Window)
69840A
18.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY (w/o Rear Power Window)
69318D
20.REMOVE DOOR LOCK WIRING HARNESS SEAL
69240
21.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY
|
Remove in this Direction | - | - |
69227L
22.REMOVE REAR DOOR OUTSIDE HANDLE COVER
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the claws to remove the rear door outside handle cover.
69241G
23.REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD
69242G
24.REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD
69204A
25.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
|
Remove in this Direction | - | - |
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the guides to remove the rear door outside handle frame sub-assembly as shown in the illustration.
68230C
26.REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>REMOVAL
75924C
27.REMOVE NO. 2 BLACK OUT TAPE
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Rear Door)>REMOVAL
68630
28.REMOVE REAR DOOR CHECK ASSEMBLY
67872
29.REMOVE REAR DOOR WEATHERSTRIP
67888D
30.REMOVE NO. 2 REAR DOOR WEATHERSTRIP
75874
31.REMOVE QUARTER PANEL WHEEL OPENING MOULDING RH
75078
32.REMOVE REAR DOOR OUTSIDE LOWER MOULDING SUB-ASSEMBLY
67837C
33.REMOVE REAR DOOR DUST PROOF SEAL (for TMMF Made)
67837C
34.REMOVE REAR DOOR DUST PROOF SEAL (for TMC Made)
for Type A:
Disengage the claws to remove the 3 rear door dust proof seals.
When installing, install 2 dust proof seals in the same way as for type B.
for Type B:
Disengage the claws to remove the 2 rear door dust proof seals.