Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › 2015.06–2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0130  Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 1)  P0132  Oxygen Sensor Circuit High Voltage Bank1 Sensor1  P2195  Oxygen Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen Sensor Signal Stuck Rich (Bank 1 Sensor 1)  


DESCRIPTION

Refer to P0031 (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0031).

HINT:

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DTC No. DTC Detection Condition Trouble Area
P0130 Voltage output of heated oxygen sensor remains at 0.4 V or more, and 0.5 V or less, during idling with warm engine (2 trip detection logic)
·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

No. 1 integration relay (EFI MAIN relay)

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


P0132 Heated oxygen sensor voltage output exceeds 1.2 V for more than 10 seconds (2 trip detection logic)
·

Short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor

·

ECM internal circuit malfunction


P2195 Output voltage of heated oxygen sensor remains at 0.5 V or less during idling with warm engine (2 trip detection logic)
·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

No. 1 integration relay (EFI MAIN relay)

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM


P2196 Output voltage of heated oxygen sensor remains at 0.4 V or more during idling with warm engine (2 trip detection logic)
·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

No. 1 integration relay (EFI MAIN relay)

·

Intake system

·

Fuel pressure

·

Fuel injector assembly

·

ECM



MONITOR DESCRIPTION

A106749E11
5.563,1.156 5.292,1.156 false 5.063,2.208 5.063,1.938 false 4.854,2.479 4.583,2.479 false 4.125,1.75 3.927,1.75 false 0.063,0.583 1.365,0.969 1.302,0.385 10 false Heated Oxygen Sensor Voltage 0.792,1.344 1.24,1.531 0.448,0.188 10 false 0.5 V 0.792,2.281 1.219,2.469 0.427,0.188 10 false 0.4 V 3.531,1.656 3.938,1.844 0.406,0.188 10 false Pass 1.292,2.74 1.917,2.958 0.625,0.219 10 false LEAN 1.323,0.719 1.948,0.938 0.625,0.219 10 false RICH 4.26,2.396 4.573,2.594 0.313,0.198 10 false Fail 4.948,1.656 5.333,1.854 0.385,0.198 10 false Fail 4.99,1.063 5.313,1.26 0.323,0.198 10 false Fail 2.667,3.021 6.146,3.219 3.479,0.198 10 false Pass / Fail Definition of Voltage Malfunction 6.406,3.01 7.031,3.229 0.625,0.219 10 false Time

The ECM uses the heated oxygen sensor information to regulate the air-fuel ratio close to a stoichiometric air-fuel ratio. This maximizes the catalytic converter's ability to purify the exhaust gases. The heated oxygen sensor detects oxygen levels in the exhaust gas and sends this signal to the ECM.

The inner surface of the sensor element is exposed to outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum coated zirconia and an integrated heating element. The heated oxygen sensor's output voltage changes suddenly in the vicinity of the stoichiometric air-fuel ratio. The heated oxygen sensor generates output voltage between 0 V and 1 V in response to the oxygen concentration in the exhaust gas. When the front heated oxygen sensor voltage is 0.45 V or more, the ECM judges that the air-fuel ratio is rich. When it is 0.45 V or less, the ECM judges that the air-fuel ratio is lean.

·

The heated oxygen sensor should indicate rich and lean alternately at a regular cycle under the air-fuel ratio feedback control. If the heated oxygen sensor voltage remains at rich or lean for about 23 seconds (x 3 times), the ECM interprets this as a malfunction of the heated oxygen sensor, illuminates the MIL (2 trip detection logic) and stores DTC P0130, 2195 or 2196.

·

If the front heated oxygen sensor output voltage exceeds 1.2 V for 10 seconds, the ECM illuminates the MIL (2 trip detection logic) and stores DTC P0132.


MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor (sensor 1)
Required Sensors/Components (Related) Crankshaft position sensor, Vehicle speed sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Time after engine start 120 seconds
Idling ON
Fuel system status Closed loop
Vehicle speed Less than 5 km/h (3 mph)
Driving record for 15 seconds or more 40 km/h (24 mph) or more and 900 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Heated oxygen sensor voltage (P0130):
Occasions either of following conditions is met More than 3 times
Minimum heated oxygen sensor voltage 0.4 V or more for 23 seconds or more
Maximum heated oxygen sensor voltage 0.5 V or less for 23 seconds or more

Heated oxygen sensor out of range (P0132)
Heated oxygen sensor voltage 1.2 V or more

Heated oxygen sensor voltage stuck Lean (P2195)
Occasions following condition is met More than 3times
Maximum heated oxygen sensor voltage 0.5 V or less for 23 seconds or more

heated oxygen sensor voltage stuck Rich (P2196)
Occasions following condition is met More than 3 times
Minimum heated oxygen sensor voltage 0.4 V or more for 23 seconds or more

COMPONENT OPERATING RANGE

Heated oxygen sensor voltage Fluctuates for a second

CONFIRMATION DRIVING PATTERN

A219223E07
1.139,2.154 1.385,2.310 0.246,0.156 10 [A] 1.761,1.963 1.982,2.133 0.222,0.170 10 [B] 2.701,1.059 2.941,1.248 0.240,0.190 10 [C] 3.438,2.004 3.684,2.216 0.246,0.211 10 [D] 6.611,3.06 6.836,3.223 0.225,0.163 10 [F] 0.036,0.618 0.979,0.811 0.943,0.193 10 Vehicle Speed 0.576,2.059 0.954,2.262 0.378,0.202 10 Idling 0.035,2.261 0.949,2.595 0.914,0.334 10 Ignition Switch ON 3.16,2.664 3.918,2.992 0.758,0.328 10 30 seconds or more 4.148,1.059 4.388,1.248 0.240,0.190 10 [C] 4.874,2.001 5.121,2.212 0.246,0.211 10 [D] 5.587,1.059 5.827,1.248 0.240,0.190 10 [C] 6.314,2.008 6.560,2.219 0.246,0.211 10 [E] 4.632,2.664 5.389,2.992 0.758,0.328 10 30 seconds or more 5.91,2.664 6.668,2.992 0.758,0.328 10 40 seconds or more 2.509,0.566 3.267,0.894 0.758,0.328 10 20 seconds or more 3.933,0.566 4.691,0.894 0.758,0.328 10 20 seconds or more 5.383,0.566 6.141,0.894 0.758,0.328 10 20 seconds or more 1.452,2.664 2.284,2.986 0.833,0.322 10 120 seconds or more 0.304,1.223 0.952,1.578 0.649,0.355 10 40 km/h (24 mph) 1.006,1.223 2.190,1.379 1.184,0.156 10 (900 rpm or more)

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and idle it for 120 seconds or more [B].

7.

Drive the vehicle at 40 km/h (24 mph) or more for 20 seconds [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Idle the engine for 30 seconds or more [D].

9.

Perform step [C] and [D] at least 3 times.

10.

Idle the engine for 40 seconds or more [E].

11.

Enter the following menus: Powertrain / Engine / DTC [F].

12.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P0130, P0132, P2195 or P2196.

15.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [F].




CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine and turn the tester on.

3.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

5.

Perform the Active Test operation with the engine idling.

6.

Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.



HINT:
·

Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Tester Display
(Sensor)
Injection Volume Status Voltage
O2S B1S1
(Heated oxygen sensor (sensor 1))
+12% Rich Higher than 0.5 V
-12% Lean Below 0.4 V
O2S B1S2
(Heated oxygen sensor (sensor 2))
+12% Rich Higher than 0.5 V
-12% Lean Below 0.4 V

NOTICE:

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


A382692E02
0.115,0.688 0.5,0.896 0.385,0.208 10 false Case 0.635,0.688 3.125,1 2.49,0.313 10 false Heated Oxygen Sensor Output Voltage 5.948,0.604 7.01,1 1.063,0.396 10 false Main Suspected Trouble Area 0.219,2.208 0.438,2.448 0.219,0.24 10 false 1 0.583,1.333 1.625,1.615 1.042,0.281 10 false Injection Volume 3.25,2.25 4.219,2.552 0.969,0.302 10 false Output Voltage 1.365,1.604 1.76,1.813 0.396,0.208 8 false +12.5% 1.375,1.844 1.896,2.083 0.521,0.24 8 false -12.5% 3.438,2.583 4.448,2.771 1.01,0.188 8 false Higher than 0.55 V 0.948,2.865 1.854,3.031 0.906,0.167 8 false Below 0.4 V 3.25,1.333 4.292,1.615 1.042,0.281 10 false Injection Volume 0.583,2.25 1.552,2.552 0.969,0.302 10 false Output Voltage 4,1.583 4.521,1.823 0.521,0.24 8 false +12.5% 4.01,1.823 4.531,2.063 0.521,0.24 8 false -12.5% 0.823,2.615 1.969,2.854 1.146,0.24 8 false Higher than 0.55 V 3.604,2.823 4.563,3 0.958,0.177 8 false Below 0.4 V 0.219,4.25 0.438,4.49 0.219,0.24 10 false 2 0.583,3.385 1.625,3.667 1.042,0.281 10 false Injection Volume 0.583,4.417 1.552,4.719 0.969,0.302 10 false Output Voltage 3.25,3.385 4.292,3.667 1.042,0.281 10 false Injection Volume 3.25,4.417 4.219,4.719 0.969,0.302 10 false Output Voltage 0.583,5.458 1.625,5.74 1.042,0.281 10 false Injection Volume 3.25,5.448 4.292,5.729 1.042,0.281 10 false Injection Volume 3.25,7.542 4.292,7.823 1.042,0.281 10 false Injection Volume 0.573,7.542 1.615,7.823 1.042,0.281 10 false Injection Volume 0.583,6.333 1.552,6.635 0.969,0.302 10 false Output Voltage 3.24,6.333 4.208,6.635 0.969,0.302 10 false Output Voltage 3.25,8.49 4.219,8.792 0.969,0.302 10 false Output Voltage 0.583,8.5 1.552,8.802 0.969,0.302 10 false Output Voltage 1.344,3.688 1.781,3.875 0.438,0.188 8 false +12.5% 3.958,3.677 4.427,3.885 0.469,0.208 8 false +12.5% 3.958,5.729 4.365,5.885 0.406,0.156 8 false +12.5% 1.333,5.74 1.729,5.927 0.396,0.188 8 false +12.5% 1.354,7.813 1.771,7.99 0.417,0.177 8 false +12.5% 4.01,7.802 4.438,7.979 0.427,0.177 8 false +12.5% 3.979,3.885 4.365,4.083 0.385,0.198 8 false -12.5% 1.354,3.896 1.875,4.135 0.521,0.24 8 false -12.5% 1.344,5.979 1.75,6.156 0.406,0.177 8 false -12.5% 3.969,5.948 4.365,6.146 0.396,0.198 8 false -12.5% 4.021,8.031 4.448,8.24 0.427,0.208 8 false -12.5% 1.344,8.01 1.75,8.177 0.406,0.167 8 false -12.5% 0.875,4.813 1.969,5.073 1.094,0.26 8 false Almost no reaction 2.594,2.75 2.844,2.958 0.25,0.208 8 false OK 5.177,2.719 5.427,2.927 0.25,0.208 8 false OK 2.542,4.729 2.792,4.938 0.25,0.208 8 false NG 5.198,4.823 5.448,5.031 0.25,0.208 8 false OK 3.583,4.927 4.5,5.104 0.917,0.177 8 false Less than 0.4 V 3.594,4.677 4.5,4.865 0.906,0.188 8 false More than 0.5 V 0.958,6.75 1.854,6.927 0.896,0.177 8 false More than 0.5 V 0.958,6.99 1.885,7.167 0.927,0.177 8 false Less than 0.4 V 3.5,6.865 4.594,7.125 1.094,0.26 8 false Almost no reaction 5.208,6.781 5.458,6.99 0.25,0.208 8 false NG 0.896,8.938 1.99,9.198 1.094,0.26 8 false Almost no reaction 2.542,8.865 2.792,9.073 0.25,0.208 8 false NG 5.208,8.875 5.458,9.083 0.25,0.208 8 false NG 3.51,8.938 4.604,9.198 1.094,0.26 8 false Almost no reaction 0.229,6.271 0.448,6.51 0.219,0.24 10 false 3 0.25,8.458 0.469,8.698 0.219,0.24 10 false 4 5.833,3.49 6.99,3.865 1.156,0.375 10 false - Heated oxygen sensor 5.865,4.021 6.969,4.552 1.104,0.531 10 false - Heated oxygen sensor heater 5.854,4.531 6.927,5.073 1.073,0.542 10 false - Heated oxygen sensor circuit 5.813,8.083 6.813,8.271 1,0.188 10 false - Fuel pressure 5.802,8.396 7.135,9.115 1.333,0.719 10 false - Gas leak from exhaust system (Air-fuel ratio extremely rich or lean) 5.865,7.479 6.781,7.854 0.917,0.375 10 false - Fuel injector assembly 5.813,5.406 6.969,5.781 1.156,0.375 10 false - No. 2 heated oxygen sensor 5.813,5.958 6.917,6.49 1.104,0.531 10 false - No. 2 heated oxygen sensor heater 5.833,6.667 7.094,7.219 1.26,0.552 10 false - No. 2 heated oxygen sensor heater circuit 3.313,0.625 5.615,0.979 2.302,0.354 10 false No. 2 Heated Oxygen Sensor Output Voltage 5.844,1.667 7,2.042 1.156,0.375 10 false - Three-way catalytic converter 5.844,2.333 7,2.708 1.156,0.375 10 false - Gas leak from exhaust system

HINT:
·

Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both the heated oxygen sensors

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / O2S B1S1 and O2S B1S2, then press the view button.



NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0130, P0132, P2195 AND/OR P2196)
a.

Connect an intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.

Result
Result Proceed to
DTC P0130, P2195 and/or P2196 are output A
DTC P0130, P0132, P2195 and/or P2196 and other DTCs are output B
DTC P0132 is output C

HINT:

If any DTCs other than P0130, P0132, P2195 and/or P2196 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR (SENSOR 1))

B

C

10.READ VALUE USING INTELLIGENT TESTER (O2S B1S1)
2.READ VALUE USING INTELLIGENT TESTER (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1.


d.

Allow the engine to run for 90 seconds at 2500 rpm.


e.

Read the heated oxygen sensor voltage while the engine is idling.

Standard voltage:

Heated oxygen sensor voltage alternates between below 0.4 V and more than 0.5 V (see the following table).



A128474E09
1.441,0.459 1.745,0.642 0.304,0.184 10 1 V 2.468,0.216 2.772,0.399 0.304,0.184 10 OK 3.422,0.216 3.726,0.399 0.304,0.184 10 NG 4.376,0.216 4.680,0.399 0.304,0.184 10 NG 5.33,0.216 5.634,0.399 0.304,0.184 10 NG 1.357,0.725 1.795,0.908 0.438,0.184 10 0.5 V 1.357,0.991 1.744,1.175 0.387,0.184 10 0.4 V 1.441,1.257 1.745,1.441 0.304,0.184 10 0 V

Result
Result Proceed to
NG A
OK B


A

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))

B

13.PERFORM CONFIRMATION DRIVING PATTERN
3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.


OK

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Turn the ignition switch to ON.


c.
U158039E02
1.844,1.021 2.24,0.771 false 0.104,0.083 0.354,0.333 0.25,0.25 10 false *a 0.5,0.958 0.823,1.167 0.323,0.208 10 false B37 2.313,0.625 2.594,0.823 0.281,0.198 10 false +B

Measure the voltage according to the value in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B37-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Heated Oxygen Sensor (Sensor 1))


OK

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

NG

9.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - NO. 1 INTEGRATION RELAY)
5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-1 (HT1A) - B84-109 (HT1A) Always Below 1 Ω
B37-3 (OX1A) - B84-112 (OX1A) Always Below 1 Ω
B37-4 (E2) - B84-90 (EX1A) Always Below 1 Ω
B37-1 (HT1A) or B84-109 (HT1A) - Body ground Always 10 kΩ or higher
B37-3 (OX1A) or B84-112 (OX1A) - Body ground Always 10 kΩ or higher
B37-4 (E2) or B84-90 (EX1A) - Body ground Always 10 kΩ or higher




OK

6.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

OK:

No leakage from intake system.




OK

7.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CHECK FUEL PRESSURE

OK

8.CHECK FUEL INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE FUEL SYSTEM

8.CHECK FUEL INJECTOR ASSEMBLY
a.

Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>1NZ-FE FUEL>FUEL INJECTOR>INSPECTION).



OK

NG

REPLACE FUEL INJECTOR ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - NO. 1 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Remove the No. 1 integration relay connector from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-4 - B37-2 (+B) Always Below 1 Ω
1E-4 or B37-2 (+B) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.READ VALUE USING INTELLIGENT TESTER (O2S B1S1)
a.

Connect the intelligent tester to the DLC3


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1


d.

Allow the engine to run at 2500 rpm for 3 minutes.


e.

Depress the accelerator pedal quickly until the engine rpm reaches 4000 rpm 3 times.

Result
Result Proceed to
Higher than 1.0 V A
1.0 V or less B



A

11.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)

B

13.PERFORM CONFIRMATION DRIVING PATTERN
11.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT)
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B84-109 (HT1A) - B84-112 (OX1A) Always 10 kΩ or higher




OK

NG

12.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
12.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.


OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

13.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0130, P0132, P2195 AND/OR P2196)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0130, P0132, P2195 AND/OR P2196)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.

Result
Result Proceed to
DTC P0130, P0132, P2195 and/or P2196 are output A
DTC is not output B



A

B