Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › 2015.06–2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0134  Oxygen Sensor Circuit No Activity Detected (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P0031 (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0031).

HINT:

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


DTC No. DTC Detection Condition Trouble Area
P0134 Heated oxygen sensor (sensor 1) output does not indicate rich (more than 0.45 V) even once when conditions (a), (b), (c), (d) and (e) continue for more than 50 seconds (1 trip detection logic):

(a) Engine speed: 1400 rpm or more

(b) Vehicle speed: 40 km/h (24 mph) or more

(c) Throttle valve not fully closed

(d) 180 seconds or more after starting engine

(e) Engine coolant temperature more than 40°C (104°F)


·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor heater (sensor 1)

·

Heated oxygen sensor (sensor 1)

·

Fuel pressure

·

Intake system

·

PCV hose connections

·

PCV valve and hose

·

Fuel injector assembly

·

Exhaust gas leakage

·

No. 1 integration relay (EFI MAIN relay)

·

ECM



HINT:

If this DTC is stored, check the output voltage of the heated oxygen sensor (sensor 1) by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / O2S B1S1.


MONITOR DESCRIPTION

The ECM uses the heated oxygen sensor to optimize the air-fuel mixture with closed loop fuel control. This control helps decrease exhaust emissions by providing the catalyst with a nearly stoichiometric mixture. The sensor detects the oxygen level in the exhaust gas and the ECM uses this data to control the air-fuel ratio. The sensor output voltage range is from 0 V to 1 V. If the signal voltage is less than 0.45 V, the air-fuel ratio is lean. If the signal voltage is more than 0.45 V, the air-fuel ratio is rich. If the sensor does not indicate rich at least once despite the conditions for the closed loop fuel control being met and the specified time period has passed, the ECM will conclude that the closed loop fuel control is malfunctioning. The ECM will illuminate the MIL and a DTC is stored.

MONITOR STRATEGY

Required Sensors/Components (Main) Heated oxygen sensor (sensor 1)
Required Sensors/Components (Related) Engine coolant temperature sensor, Throttle with motor body assembly, Crankshaft position sensor, Vehicle speed sensor
Frequency of Operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Intrusive closed loop is performed when following conditions met -
Duration that the following conditions met 50 seconds
Engine coolant temperature 40°C (104°F) or higher
Engine speed 1400 rpm or more
Vehicle speed 40 km/h or more
Idle OFF
Battery voltage 11 V or more

TYPICAL MALFUNCTION THRESHOLDS

Oxygen sensor voltage Less than 0.45 V

CONFIRMATION DRIVING PATTERN

A219224E07
2.042,2.302 2.302,2.479 0.26,0.177 10 false [A] 2.594,2.052 2.813,2.219 0.219,0.167 10 false [B] 4.604,1.021 4.844,1.208 0.24,0.188 10 false [C] 5.635,3.24 5.896,3.458 0.26,0.219 10 false [D] 0.885,0.542 1.833,0.74 0.948,0.198 10 false Vehicle Speed 1.427,2.188 1.844,2.385 0.417,0.198 10 false Idling 0.854,2.406 1.792,2.74 0.938,0.333 10 false Ignition Switch ON 2.313,2.875 3.094,3.063 0.781,0.188 10 false Warming up 4.094,2.875 5.302,3.052 1.208,0.177 10 false 4 minutes or more 1.219,1.406 1.823,1.76 0.604,0.354 10 false 40 km/h (24 mph)

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 40°C (104°F) or higher [B].

7.

Drive the vehicle at 40 km/h (24 mph) or more for 4 minutes or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0134.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [D] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume operation using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Start the engine and turn the tester on.

3.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

4.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.

5.

Perform the Active Test operation with the engine idling.

6.

Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.



HINT:
·

Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



Tester Display
(Sensor)
Injection Volume Status Voltage
O2S B1S1
(Heated oxygen sensor (sensor 1))
+12% Rich Higher than 0.5 V
-12% Lean Below 0.4 V
O2S B1S2
(Heated oxygen sensor (sensor 2))
+12% Rich Higher than 0.5 V
-12% Lean Below 0.4 V

NOTICE:

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


A382692E02
0.115,0.688 0.5,0.896 0.385,0.208 10 false Case 0.635,0.688 3.125,1 2.49,0.313 10 false Heated Oxygen Sensor Output Voltage 5.948,0.604 7.01,1 1.063,0.396 10 false Main Suspected Trouble Area 0.219,2.208 0.438,2.448 0.219,0.24 10 false 1 0.583,1.333 1.625,1.615 1.042,0.281 10 false Injection Volume 3.25,2.25 4.219,2.552 0.969,0.302 10 false Output Voltage 1.365,1.604 1.76,1.813 0.396,0.208 8 false +12.5% 1.375,1.844 1.896,2.083 0.521,0.24 8 false -12.5% 3.438,2.583 4.448,2.771 1.01,0.188 8 false Higher than 0.55 V 0.948,2.865 1.854,3.031 0.906,0.167 8 false Below 0.4 V 3.25,1.333 4.292,1.615 1.042,0.281 10 false Injection Volume 0.583,2.25 1.552,2.552 0.969,0.302 10 false Output Voltage 4,1.583 4.521,1.823 0.521,0.24 8 false +12.5% 4.01,1.823 4.531,2.063 0.521,0.24 8 false -12.5% 0.823,2.615 1.969,2.854 1.146,0.24 8 false Higher than 0.55 V 3.604,2.823 4.563,3 0.958,0.177 8 false Below 0.4 V 0.219,4.25 0.438,4.49 0.219,0.24 10 false 2 0.583,3.385 1.625,3.667 1.042,0.281 10 false Injection Volume 0.583,4.417 1.552,4.719 0.969,0.302 10 false Output Voltage 3.25,3.385 4.292,3.667 1.042,0.281 10 false Injection Volume 3.25,4.417 4.219,4.719 0.969,0.302 10 false Output Voltage 0.583,5.458 1.625,5.74 1.042,0.281 10 false Injection Volume 3.25,5.448 4.292,5.729 1.042,0.281 10 false Injection Volume 3.25,7.542 4.292,7.823 1.042,0.281 10 false Injection Volume 0.573,7.542 1.615,7.823 1.042,0.281 10 false Injection Volume 0.583,6.333 1.552,6.635 0.969,0.302 10 false Output Voltage 3.24,6.333 4.208,6.635 0.969,0.302 10 false Output Voltage 3.25,8.49 4.219,8.792 0.969,0.302 10 false Output Voltage 0.583,8.5 1.552,8.802 0.969,0.302 10 false Output Voltage 1.344,3.688 1.781,3.875 0.438,0.188 8 false +12.5% 3.958,3.677 4.427,3.885 0.469,0.208 8 false +12.5% 3.958,5.729 4.365,5.885 0.406,0.156 8 false +12.5% 1.333,5.74 1.729,5.927 0.396,0.188 8 false +12.5% 1.354,7.813 1.771,7.99 0.417,0.177 8 false +12.5% 4.01,7.802 4.438,7.979 0.427,0.177 8 false +12.5% 3.979,3.885 4.365,4.083 0.385,0.198 8 false -12.5% 1.354,3.896 1.875,4.135 0.521,0.24 8 false -12.5% 1.344,5.979 1.75,6.156 0.406,0.177 8 false -12.5% 3.969,5.948 4.365,6.146 0.396,0.198 8 false -12.5% 4.021,8.031 4.448,8.24 0.427,0.208 8 false -12.5% 1.344,8.01 1.75,8.177 0.406,0.167 8 false -12.5% 0.875,4.813 1.969,5.073 1.094,0.26 8 false Almost no reaction 2.594,2.75 2.844,2.958 0.25,0.208 8 false OK 5.177,2.719 5.427,2.927 0.25,0.208 8 false OK 2.542,4.729 2.792,4.938 0.25,0.208 8 false NG 5.198,4.823 5.448,5.031 0.25,0.208 8 false OK 3.583,4.927 4.5,5.104 0.917,0.177 8 false Less than 0.4 V 3.594,4.677 4.5,4.865 0.906,0.188 8 false More than 0.5 V 0.958,6.75 1.854,6.927 0.896,0.177 8 false More than 0.5 V 0.958,6.99 1.885,7.167 0.927,0.177 8 false Less than 0.4 V 3.5,6.865 4.594,7.125 1.094,0.26 8 false Almost no reaction 5.208,6.781 5.458,6.99 0.25,0.208 8 false NG 0.896,8.938 1.99,9.198 1.094,0.26 8 false Almost no reaction 2.542,8.865 2.792,9.073 0.25,0.208 8 false NG 5.208,8.875 5.458,9.083 0.25,0.208 8 false NG 3.51,8.938 4.604,9.198 1.094,0.26 8 false Almost no reaction 0.229,6.271 0.448,6.51 0.219,0.24 10 false 3 0.25,8.458 0.469,8.698 0.219,0.24 10 false 4 5.833,3.49 6.99,3.865 1.156,0.375 10 false - Heated oxygen sensor 5.865,4.021 6.969,4.552 1.104,0.531 10 false - Heated oxygen sensor heater 5.854,4.531 6.927,5.073 1.073,0.542 10 false - Heated oxygen sensor circuit 5.813,8.083 6.813,8.271 1,0.188 10 false - Fuel pressure 5.802,8.396 7.135,9.115 1.333,0.719 10 false - Gas leak from exhaust system (Air-fuel ratio extremely rich or lean) 5.865,7.479 6.781,7.854 0.917,0.375 10 false - Fuel injector assembly 5.813,5.406 6.969,5.781 1.156,0.375 10 false - No. 2 heated oxygen sensor 5.813,5.958 6.917,6.49 1.104,0.531 10 false - No. 2 heated oxygen sensor heater 5.833,6.667 7.094,7.219 1.26,0.552 10 false - No. 2 heated oxygen sensor heater circuit 3.313,0.625 5.615,0.979 2.302,0.354 10 false No. 2 Heated Oxygen Sensor Output Voltage 5.844,1.667 7,2.042 1.156,0.375 10 false - Three-way catalytic converter 5.844,2.333 7,2.708 1.156,0.375 10 false - Gas leak from exhaust system

HINT:
·

Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both the heated oxygen sensors

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / O2S B1S1 and O2S B1S2, then press the view button.



NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0134)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.

Result
Result Proceed to
DTC P0134 is output A
DTC P0134 and other DTCs are output B


HINT:

If any DTCs other than P0134 are output, troubleshoot those DTCs first.



A

2.READ VALUE USING INTELLIGENT TESTER (O2S B1S1)

B

2.READ VALUE USING INTELLIGENT TESTER (O2S B1S1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1 and Engine Speed.


e.

Warm up the engine until the engine coolant temperature reaches more than 40°C (104°F).


f.

Rev the engine up to 4000 rpm 3 times using the accelerator pedal.


g.

Read the output voltage of the heated oxygen sensor (sensor 1) displayed on the tester when the engine speed is suddenly increased.

Standard voltage:

Heated oxygen sensor voltage output indicates 0.45 V or more (rich signal) at least once.


Result
Result Proceed to
NG A
OK B



A

3.CHECK PCV HOSE CONNECTIONS

B

12.PERFORM CONFIRMATION DRIVING PATTERN
3.CHECK PCV HOSE CONNECTIONS
a.

Inspect the PCV hose connections (See page Engine / Hybrid System>1NZ-FE EMISSION CONTROL>PCV VALVE>COMPONENTS).


OK:

PCV hose is connected correctly and is not damaged.



OK

4.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))

NG

REPAIR OR REPLACE PCV HOSE

4.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.


OK

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))

NG

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 1))
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Turn the ignition switch to ON.


c.
U158041E02
1.865,1 2.26,0.75 false 0.094,0.063 0.292,0.313 0.198,0.25 10 false *a 0.469,0.948 0.823,1.167 0.354,0.219 10 false B37 2.313,0.625 2.563,0.823 0.25,0.198 10 false +B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B37-2 (+B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
( to heated oxygen sensor (sensor 1))



OK

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

NG

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - NO. 1 INTEGRATION RELAY)
6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-1 (HT1A) - B84-109 (HT1A) Always Below 1 Ω
B37-3 (OX1A) - B84-112 (OX1A) Always Below 1 Ω
B37-4 (E2) - B84-90 (EX1A) Always Below 1 Ω
B37-1 (HT1A) or B84-109 (HT1A)- Body ground Always 10 kΩ or higher
B37-3 (OX1A) or B84-112 (OX1A) - Body ground Always 10 kΩ or higher
B37-4 (E2) or B84-90 (EX1A) - Body ground Always 10 kΩ or higher




OK

7.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>1NZ-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leakage from intake system.




OK

8.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

8.CHECK FUEL PRESSURE

OK

9.INSPECT FUEL INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE FUEL SYSTEM

9.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>1NZ-FE FUEL>FUEL INJECTOR>INSPECTION).



OK

10.CHECK FOR EXHAUST GAS LEAK

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.


OK:

No gas leak.



OK

NG

REPAIR OR REPLACE EXHAUST GAS LEAKAGE POINT

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - NO. 1 INTEGRATION RELAY)
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Remove the No. 1 integration relay connector from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B37-2 (+B) - 1E-4 Always Below 1 Ω
B37-2 (+B) or 1E-4 Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.



NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0134)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P0134)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0134 is output B



A

14.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

14.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?



YES

DTC CAUSED BY RUNNING OUT OF FUEL

NO