Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB › from 2014.07
RM19S0E _52 Drivetrain _051470 AXLE AND DIFFERENTIAL _0248209 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side as for the LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 89543 3.SEPARATE FRONT SPEED SENSOR (w/ ABS)

a.
C107502

Remove the bolt and separate the speed sensor and flexible hose.


b.
C112274

Remove the bolt and separate the speed sensor from the steering knuckle.

NOTICE:
·

Keep the speed sensor tip and installation portion free of foreign matter.

·

Remove the speed sensor without turning it from its original installation angle.




Hide 4.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

a.
C085618

Remove the 2 bolts and separate the disc brake caliper assembly.

NOTICE:

Hang the caliper using a piece of string or the equivalent.



Hide 43512 5.REMOVE FRONT DISC

Hide 45047 6.SEPARATE TIE ROD END SUB-ASSEMBLY

a.

Remove the cotter pin and castle nut.


b.
C172757E03
2.498,0.869 2.305,1.24 false 2.52,0.735 2.877,0.898 0.357,0.163 10 SST

Install SST to the threaded section of the tie rod end.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure the upper ends of the threaded section of the tie rod end and SST are aligned.



c.

Using SST, separate the tie rod end from the front axle assembly.

U158303E02
5.219,2.125 5.49,1.927 false 1.49,2.188 1.719,1.927 false 5.021,2.135 5.188,2.313 0.167,0.177 10 false *a 6.188,0.708 6.313,0.917 0.125,0.208 10 false A 6.188,1.073 6.313,1.281 0.125,0.208 10 false B 1.313,2.208 1.646,2.563 0.333,0.354 10 false SST

Text in Illustration
*a Place the wrench here - -
V100135

Apply grease to the bolt threads and the tip of SST. - -

SST
09960-20010  (09961-02010)

NOTICE:
·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Install SST so that A and B are parallel.

·

Be sure to place the wrench on the part indicated in the illustration.

·

Do not damage the ball joint dust cover.

·

Do not damage the front disc brake dust cover.




Hide 48069 7.SEPARATE FRONT LOWER SUSPENSION ARM

a.

Remove the clip and castle nut.


b.
C172759E05
2.531,0.936 2.853,1.085 0.322,0.149 10 SST 2.503,1.029 2.36,1.273 false

Install SST to the threaded section of the lower ball joint.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure the upper ends of the threaded section of the lower ball joint and SST are aligned.



c.

Using SST, separate the lower arm.

U158304E01
4.994,1.988 5.158,2.147 0.164,0.158 10 *a 5.164,2.047 5.469,1.833 false 6.138,0.625 6.363,0.934 0.225,0.309 10 A 6.138,0.982 6.457,1.301 0.319,0.319 10 B 1.403,2.404 1.739,2.588 0.336,0.184 10 SST 1.55,2.376 1.893,2.229 false

Text in Illustration
*a Place the wrench here - -
V100135

Apply grease to the bolt threads and the tip of SST. - -

SST
09960-20010  (09961-02010)

NOTICE:
·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Install SST so that A and B are parallel.

·

Be sure to place the wrench on the part indicated in the illustration.

·

Do not damage the lower ball joint dust cover.

·

Do not damage the drive shaft outboard joint boots.

·

Do not damage the front disc brake dust cover.




Hide 48810 8.SEPARATE FRONT STABILIZER LINK ASSEMBLY

Hide 9.REMOVE FRONT AXLE ASSEMBLY

a.

Using a plastic hammer, tap the end of the drive shaft and separate the fitting between the drive shaft and front axle hub.

NOTICE:

Do not hammer the threads of the drive shaft.


HINT:

If it is difficult to separate the fitting, tap the end of the drive shaft with a brass bar and hammer.



b.
C125277

Remove the 2 nuts, 2 bolts and the front axle assembly.

NOTICE:
·

Do not damage the lower ball joint.

·

Do not damage the threads of the drive shaft.

·

Do not damage the speed sensor rotor.

·

Do not damage the drive shaft outboard joint boot.

·

Suspend the drive shaft with a piece of string or equivalent.



HINT:

Keep the bolt from rotating while turning the nut.



Hide 43502G 10.REMOVE FRONT AXLE HUB HOLE SNAP RING

a.
C202595E01
0.728,0.325 0.951,0.504 0.224,0.178 10 *1 0.895,0.417 1.496,0.803 false

Using snap ring pliers, remove the axle hub hole snap ring.

Text in Illustration
*1 Snap Ring Pliers

NOTICE:

When removing the hole snap ring, do not damage the magnetic rotor surface.



Hide 43502C 11.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

a.
C355449E01
0.677,1.146 0.677,0.688 false 0.552,0.51 1.01,0.708 0.458,0.198 10 false SST

Fix the steering knuckle in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using SST, remove the axle hub.

SST
09520-00031  


c.
C202597E02
1.708,0.252 2.032,0.415 0.325,0.163 10 SST 1.61,1.644 1.935,1.807 0.325,0.163 10 SST 1.676,0.335 1.355,0.765 false 1.576,1.716 0.966,1.478 false 2.465,0.192 2.652,0.372 0.187,0.180 10 *a 0.249,0.202 0.436,0.383 0.187,0.180 10 *b

Using SST, remove the axle hub bearing inner race.

Text in Illustration
*a Hold
*b Turn

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04011, 09957-04010, 09958-04011)
09950-60010  (09951-00370)

NOTICE:
·

When removing the inner race, it the axle hub is damaged, replace the axle hub with a new one.

·

Apply a small amount of grease to the threads and tip of SST before use.




Hide 43502E 12.REMOVE FRONT AXLE HUB BEARING