Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › 2011.08–2014.07
RM19S0E _53 Suspension _051472 FRONT SUSPENSION _0248218 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 12363A 1.INSTALL ENGINE MOVING CONTROL ROD

a.

Install the engine moving control rod with the bolt.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)

HINT:

Temporarily tighten the transaxle side, and then tighten the bolt to the specified torque.



Hide 48069 2.TEMPORARILY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

a.

Install the front lower suspension arm sub-assembly LH with the bolt.


Hide 48068 3.TEMPORARILY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 48811 4.INSTALL FRONT STABILIZER BAR

Hide 48829A 5.INSTALL FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 6.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 51201 8.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C233132

Place wooden blocks or plate lift attachments on an engine lifter, and then set the front suspension crossmember sub-assembly so that the attachments are in the positions shown in the illustration.

Text in Illustration
V100135

Front of the Vehicle
V100144

Attachment Placement Positions


b.

Provisionally install the front suspension crossmember sub-assembly onto the body with the 6 bolts.


c.

By inserting SST into the datum holes in the front suspension crossmembers RH and LH alternately, tighten bolts A, B and C on both sides to the specified torque, in several steps.

C233133E01
4.312,1.479 4.466,1.624 0.154,0.145 10 *a 4.458,1.502 4.568,1.303 false 2.799,1.479 2.953,1.624 0.154,0.145 10 *a 5.562,2.051 5.685,2.196 0.124,0.145 10 A 5.333,2.457 5.457,2.603 0.124,0.145 10 B 5.361,2.654 5.485,2.799 0.124,0.145 10 C 1.513,1.981 1.636,2.126 0.124,0.145 10 A 1.774,2.429 1.898,2.575 0.124,0.145 10 B 3.803,2.574 4.103,2.719 0.300,0.145 10 SST 4.091,2.638 4.72,2.638 false 3.159,2.574 3.459,2.719 0.300,0.145 10 SST 5.76,3.517 5.989,3.662 0.228,0.145 10 NG 5.018,3.517 5.246,3.662 0.228,0.145 10 OK 2.468,3.517 2.696,3.662 0.228,0.145 10 NG 1.725,3.517 1.954,3.662 0.228,0.145 10 OK 1.774,2.64 1.898,2.785 0.124,0.145 10 C 2.782,1.502 2.693,1.288 false 3.135,2.638 2.508,2.638 false

Text in Illustration
*a Datum Hole - -
V100135

Front of the Vehicle - -

SST
09670-00011  
09670-00020  

Torque:
Bolt A : 87 N*m (887 kgf*cm, 64 ft.*lbf)
Bolt B : 151 N*m (1540 kgf*cm, 111 ft.*lbf)
Bolt C : 98 N*m (999 kgf*cm, 72 ft.*lbf)

NOTICE:
·

Insert SST into the datum hole in a vertical orientation.

·

If SST cannot be inserted into the datum hole vertically, loosen all the bolts and then insert SST again.




d.

Install the engine moving control rod with the bolt.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


Hide 48069 9.INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 10.INSTALL FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 45047 11.INSTALL TIE ROD END SUB-ASSEMBLY LH

Hide 45046 12.INSTALL TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 48810 13.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

a.

Install the front stabilizer link assembly LH with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

HINT:

Using a socket hexagon wrench 6 to hold the stud.



Hide 48820B 14.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 45025D 15.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.

Install clip B onto the body portion and install the No. 1 steering column hole cover onto the body portion with clip A.

NOTICE:

Make sure that the lip portion of steering column hole cover is not damaged.



Hide 45209 16.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C245426E02
2.409,1.3 2.557,1.442 0.149,0.142 10 *1 2.286,1.042 2.400,1.184 0.114,0.142 10 A 2.077,1.436 2.191,1.577 0.114,0.142 10 B 0.809,1.326 0.958,1.468 0.149,0.142 10 *a 2.392,1.386 2.229,1.386 2.229,1.386 1.916,1.077 false 1.558,1.563 1.017,1.438 1.017,1.438 1.524,1.664 false

Align the matchmarks and install the steering sliding yoke sub-assembly onto the manual steering gear.

Text in Illustration
*1 Steering Sliding Yoke Sub-assembly
*a Matchmarks


b.

Install the bolt B.

Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


c.

Tighten bolt A.

Torque:
35 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 45259A 17.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 18.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 19. POSITION WHEELS FACING STRAIGHT AHEAD

Hide 20. STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Bounce the vehicle up and down several times to stabilize the suspension.


Hide 48069 21.FULLY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 22.FULLY TIGHTEN FRONT LOWER SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 51405A 23.INSTALL ENGINE UNDER COVER SUB-ASSEMBLY (for Metal Type)

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

Hide 24.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT