Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248226 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1405  Open or Short in Front Speed Sensor RH Circuit  C1406  Open or Short in Front Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1271).

DTC No. DTC Detection Condition Trouble Area
C1405
C1406
Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTC C1405 is for the front speed sensor RH.

·

DTC C1406 is for the front speed sensor LH.



WIRING DIAGRAM

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Speed Open FR speed sensor open detection / Normal or Error Normal: Normal
Error: Momentary interruption
-
FL Speed Open FL speed sensor open detection / Normal or Error Normal: Normal
Error: Momentary interruption
-

OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.




OK

2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)

OK

3.RECONFIRM DTC

NG

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
3.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Result
Result Proceed to
DTCs C1405 and C1406 are not output A
DTCs C1405 and/or C1406 are output (for LHD) B
DTCs C1405 and/or C1406) are output (for RHD) C

HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).



A

B

C

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU connector and the front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-7 (FR+) - A18-2 (FR+) Always Below 1 Ω
A55-6 (FR-) - A18-1 (FR-) Always Below 1 Ω
A55-19 (FL+) - A19-2 (FL+) Always Below 1 Ω
A55-18 (FL-) - A19-1 (FL-) Always Below 1 Ω
A55-7 (FR+) - Body ground Always 10 kΩ or higher
A55-6 (FR-) - Body ground Always 10 kΩ or higher
A55-19 (FL+) - Body ground Always 10 kΩ or higher
A55-18 (FL-) - Body ground Always 10 kΩ or higher



e.

Reconnect the skid control ECU connector and the front speed sensor connector.



OK

5.INSPECT SKID CONTROL ECU (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SKID CONTROL ECU (SENSOR INPUT)
a.
U126968E01
2.444,1.808 2.816,1.961 0.372,0.153 10 FL+ 1.095,1.808 1.467,1.961 0.372,0.153 10 FR+ 0.966,1.344 1.172,1.786 false 2.324,1.344 2.53,1.786 false 0.135,0.086 0.321,0.247 0.186,0.161 10 *a 0.739,0.577 1.035,0.734 0.295,0.156 10 A18 2.092,0.577 2.388,0.734 0.295,0.156 10 A19

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A18-2 (FR+) - Body ground Ignition switch to ON 8 to 14 V
A19-2 (FL+) - Body ground Ignition switch to ON 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).



Text in illustration
*a Front view of wire harness connector
(to Front Speed Sensor)

Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

B

C