Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248226 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1407  Open or Short in Rear Speed Sensor RH Circuit  C1408  Open or Short in Rear Speed Sensor LH Circuit  


DESCRIPTION

Refer to DTCs C1403 and C1404 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1273).

DTC No. DTC Detection Condition Trouble Area
C1407
C1408
Either of the following is detected:
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor RH/LH

·

Skid control sensor wire RH/LH

·

Speed sensor circuit

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTC C1407 is for the rear speed sensor RH.

·

DTC C1408 is for the rear speed sensor LH.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Disassembly of the rear speed sensor from the rear axle hub and bearing assembly is prohibited.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to the DTC (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Speed Open RR speed sensor open detection / Normal or Error Normal: Normal
Error: Momentary interruption
-
RL Speed Open RL speed sensor open detection / Normal or Error Normal: Normal
Error: Momentary interruption
-

OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.




OK

2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

NG

4.INSPECT SKID CONTROL SENSOR WIRE
2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR)

OK

3.RECONFIRM DTC

NG

4.INSPECT SKID CONTROL SENSOR WIRE
3.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Result
Result Proceed to
DTCs C1407 and C1408 are not output A
DTCs C1407 and/or C1408 are output (for LHD) B
DTCs C1407 and/or C1408 are output (for RHD) C

HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).



A

B

C

4.INSPECT SKID CONTROL SENSOR WIRE
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control sensor wire connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (RH):
Tester Connection Condition Specified Condition
W1-2 (+) - WK1-1 Always Below 1 Ω
W1-1 (-) - WK1-2 Always Below 1 Ω
W1-2 (+) - WK1-2 Always 10 kΩ or higher
W1-2 (+) - Body ground Always 10 kΩ or higher
W1-1 (-) - WK1-1 Always 10 kΩ or higher
W1-1 (-) - Body ground Always 10 kΩ or higher


Standard Resistance (LH):
Tester Connection Condition Specified Condition
V1-2 (+) - VK1-1 Always Below 1 Ω
V1-1 (-) - VK1-2 Always Below 1 Ω
V1-2 (+) - VK1-2 Always 10 kΩ or higher
V1-2 (+) - Body ground Always 10 kΩ or higher
V1-1 (-) - VK1-1 Always 10 kΩ or higher
V1-1 (-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).



e.

Reconnect the skid control sensor wire connector.



OK

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

NG

REPLACE SKID CONTROL SENSOR WIRE

5.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the skid control ECU connector and the rear speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-17 (RR+) - W1-2 (+) Always Below 1 Ω
A55-16 (RR-) - W1-1 (-) Always Below 1 Ω
A55-5 (RL+) - V1-2 (+) Always Below 1 Ω
A55-4 (RL-) - V1-1 (-) Always Below 1 Ω
A55-17 (RR+) - Body ground Always 10 kΩ or higher
A55-16 (RR-) - Body ground Always 10 kΩ or higher
A55-5 (RL+) - Body ground Always 10 kΩ or higher
A55-4 (RL-) - Body ground Always 10 kΩ or higher



e.

Reconnect the skid control ECU connector.



OK

6.INSPECT SKID CONTROL ECU (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT SKID CONTROL ECU (SENSOR INPUT)
a.
U126969E01
1.141,1.789 1.253,1.942 0.112,0.153 10 + 2.494,1.789 2.605,1.942 0.112,0.153 10 + 0.966,1.344 1.172,1.786 false 2.324,1.344 2.529,1.786 false 0.135,0.086 0.321,0.247 0.186,0.161 10 *a 0.765,0.577 1.061,0.734 0.295,0.156 10 W1 2.138,0.577 2.433,0.734 0.295,0.156 10 V1

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (RH):
Tester Connection Switch Condition Specified Condition
W1-2 (+) - Body ground Ignition switch ON 8 to 14 V
V1-2 (+) - Body ground Ignition switch ON 8 to 14 V


NOTICE:

Check the speed sensor signal after replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).



Text in illustration
*a Front view of wire harness connector
(to Rear Speed Sensor)

c.

Reconnect the rear speed sensor connector.


Result
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C


A

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY

B

C