Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248226 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C146C  Open in ABS Motor Relay Circuit  C146D  Short in ABS Motor Relay Circuit  


DESCRIPTION

The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the ABS pump motor.

If the voltage supplied to the motor relay (+BM) is below the DTC's detection threshold due to low voltage from the battery or generator, the DTC may be stored.

DTC No. DTC Detection Condition Trouble Area
C146C When either of the following is detected:
1.

All of the following conditions continue for 0.12 seconds or more.

-

The IG1 terminal voltage is between 9.5 and 17.2 V.

-

While initial check and ABS is operating.

-

Relay contact is open when the relay is ON.


2.

Both of the following conditions continue for 0.12 seconds.

-

The IG1 terminal voltage is less than 9.5 V.

-

Relay contact remains open when the relay is ON.



·

ABS NO. 1 fuse

·

ABS motor relay circuit

·

Brake actuator assembly (ABS motor relay)


C146D When the motor relay is OFF, the motor relay remains closed for 4 seconds or more.
·

ABS motor relay circuit

·

Brake actuator assembly (ABS motor relay)



WIRING DIAGRAM

C243324E01
4.825,0.628 5.956,0.784 1.130,0.156 10 Skid Control ECU 5.099,1.289 5.883,1.463 0.784,0.174 10 Motor Relay 3.822,1.503 4.169,1.670 0.347,0.166 10 +BM 3.505,1.24 3.696,1.413 0.191,0.174 10 24 1.885,1.56 2.628,1.885 0.744,0.325 10 ABS NO. 1 0.763,2.14 1.052,2.310 0.289,0.170 10 ALT 0.85,4.083 1.372,4.246 0.522,0.162 10 Battery 3.492,2.899 3.689,3.064 0.197,0.165 10 13 3.788,3.123 4.216,3.283 0.428,0.161 10 GND2 5.209,4.437 6.028,4.595 0.820,0.159 10 Pump Motor 4.554,4.933 4.988,5.098 0.433,0.165 10 A55 4.554,5.094 6.217,5.301 1.663,0.207 10 Brake Actuator Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

When C1241 is output together with C146C and/or C146D inspect and repair the trouble areas indicated by C1241 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1241).


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.



e.

Enter the following menu: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Motor Relay ABS motor relay Relay ON / OFF Operating sound of motor can be heard.


f.

Check the operating sound of the ABS motor relay when operating it with the intelligent tester.


Result
Result Proceed to
The operating sound is not heard A
The operating sound is heard B


A

2.CHECK TERMINAL VOLTAGE (+BM TERMINAL)

B

4.RECONFIRM DTC
2.CHECK TERMINAL VOLTAGE (+BM TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Check the connector case and terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.
U158344E01
1.719,0.159 2.014,0.340 0.295,0.181 10 A55 0.125,0.103 0.316,0.265 0.191,0.163 10 *a 2.121,1.983 2.467,2.125 0.346,0.142 10 +BM 2.555,1.271 2.292,1.966 false

Disconnect the skid control ECU connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-24 (+BM) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid control ECU)


f.

Turn the ignition switch off.



OK

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
U158345E01
1.719,0.159 2.014,0.340 0.295,0.181 10 A55 0.125,0.103 0.316,0.265 0.191,0.163 10 *a 0.746,1.983 1.155,2.125 0.409,0.142 10 GND2 1.197,1.271 0.985,1.966 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-13 (GND2) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Skid control ECU)


OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)