The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.
If any of the following is detected, the brake warning light remains on:
The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
The brake fluid level is insufficient.
The parking brake is applied.
EBD operation is not possible.
When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>CALIBRATION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
OK
NG
A
B
A
B
C
OK
NG
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Parking Brake SW | Parking brake switch/OFF or ON | OFF: Parking brake released
ON: Parking brake applied |
- |
Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.
When the parking brake is operated, the display changes as shown above.
OK
NG
Turn the ignition switch off.
Remove the reservoir filler cap and strainer.
Disconnect the brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Switch off (Float up) | 10 kΩ or higher |
| Switch on (Float down) | Below 1 Ω |
If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.
| *a | Component without harness connected
(Brake Fluid Level Warning Switch) |
Reconnect the brake fluid level warning switch connector.
Reinstall the reservoir filler cap and strainer.
OK
NG
Disconnect the combination meter assembly connector and the brake fluid level warning switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-12 (SW) - A25-1 (+) | Always | Below 1 Ω |
| A25-2 (E) - Body ground | Always | Below 1 Ω |
| F1-12 (SW) - Body ground | Always | 10 kΩ or higher |
Reconnect the combination meter assembly connector and the brake fluid level warning switch.
OK
NG
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Brake Warning Light | Brake warning light/OFF or ON | OFF: Warning light off
ON: Warning light on |
- |
When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Brake Warning Light | Brake warning light | Warning light OFF/ON | Observe combination meter
[Vehicle condition] Vehicle stopped |
| Result | Proceed to | |
|---|---|---|
| Data List Display | Data List Display when Performing Active Test ON/OFF Operation | |
| ON | Changes between ON and OFF | A |
| Does not change between ON and OFF | B | |
| OFF | Changes between ON and OFF | A |
| Does not change between ON and OFF | B | |
Connect the intelligent tester to the DLC3.
A
B
NEXT
Connect the intelligent tester to the DLC3.
Perform Active Test of the combination meter assembly using the intelligent tester (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).
The brake warning light turns ON or OFF in accordance with the intelligent tester.
OK
NG
Remove the parking brake switch assembly (See page Brake>PARKING BRAKE>PARKING BRAKE SWITCH>REMOVAL).
Inspect the parking brake switch assembly (See page Brake>PARKING BRAKE>PARKING BRAKE SWITCH>INSPECTION).
OK
NG
Disconnect the instrument panel junction block assembly connector and the parking brake switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-28 (PKB) - F22-1 | Always | Below 1 Ω |
| 3A-28 (PKB) - Body ground | Always | 10 kΩ or higher |
Reconnect the instrument panel junction block assembly connector and the parking brake switch assembly connector.
OK
NG
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Disconnect the instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-28 -12 (PKB) | Always | Below 1 Ω |
| 3A-28 - Body ground | Always | 10 kΩ or higher |
Reconnect the instrument panel junction block assembly connector.
Reinstall the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.
OK
NG