Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) › 2011.08–2017.01
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248235 VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

EBD operation is not possible.


WIRING DIAGRAM

C243295E07
2.854,0.625 3.813,0.76 0.958,0.135 10 false ECU-IG NO. 2 4.792,0.333 4.969,0.5 0.177,0.167 10 false 34 4.833,1.385 5.01,1.521 0.177,0.135 10 false 1 4.719,2.51 4.99,2.656 0.271,0.146 10 false A54 5.115,0.458 5.385,0.625 0.271,0.167 10 false IG1 5.125,1.5 5.552,1.667 0.427,0.167 10 false GND1 4.802,2.729 6.552,3.042 1.75,0.313 10 false Skid Control ECU (Brake Actuator Assembly) 2.625,1.542 2.802,1.698 0.177,0.156 10 false IG 2.375,2.063 2.771,2.229 0.396,0.167 10 false Brake 2.271,2.583 2.583,2.729 0.313,0.146 10 false CPU 1.5,3.552 1.771,3.708 0.271,0.156 10 false SW 1.24,3.427 1.427,3.573 0.188,0.146 10 false 12 2.156,3.948 2.677,4.094 0.521,0.146 10 false CAN I/F 1.5,4.531 1.698,4.677 0.198,0.146 10 false F1 1.719,4.531 3.573,4.698 1.854,0.167 10 false Combination Meter Assembly 0.292,4.198 0.396,4.354 0.104,0.156 10 false 1 0.656,4.708 0.927,4.854 0.271,0.146 10 false A25 0.667,4.875 2.406,5.365 1.74,0.49 10 false Brake Master Cylinder Reservoir Assembly (Brake Fluid Level Warning Switch) 0.469,4.427 0.573,4.573 0.104,0.146 10 false + 0.448,5.104 0.573,5.25 0.125,0.146 10 false E 0.302,5.302 0.396,5.448 0.094,0.146 10 false 2 4.125,5.052 4.219,5.208 0.094,0.156 10 false 1 2.896,5.302 3.177,5.448 0.281,0.146 10 false F22 2.896,5.448 4.885,5.615 1.99,0.167 10 false Parking Brake Switch Assembly 5.104,4.073 6.125,4.24 1.021,0.167 10 false Main Body ECU 5.115,5.156 5.302,5.302 0.188,0.146 10 false 3A 5.146,4.979 5.323,5.135 0.177,0.156 10 false 28 5.74,4.969 5.917,5.125 0.177,0.156 10 false 12 4.969,5.552 6.604,5.865 1.635,0.313 10 false Instrument Panel Junction Block Assembly 0.74,6.354 2.479,6.521 1.74,0.167 10 false : CAN Communication Line 5.594,4.75 5.896,4.906 0.302,0.156 10 false PKB

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the tester, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch/OFF or ON OFF: Parking brake released
ON: Parking brake applied
-


f.

Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.

OK:

When the parking brake is operated, the display changes as shown above.




OK

7.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)

NG

12.INSPECT PARKING BRAKE SWITCH ASSEMBLY
7.INSPECT BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH)
a.
C235854E01
0.175,0.239 0.361,0.400 0.186,0.161 10 *a

Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the brake fluid level warning switch connector.


d.

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch off (Float up) 10 kΩ or higher
Switch on (Float down) Below 1 Ω


HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch)

e.

Reconnect the brake fluid level warning switch connector.


f.

Reinstall the reservoir filler cap and strainer.



OK

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Disconnect the combination meter assembly connector and the brake fluid level warning switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F1-12 (SW) - A25-1 (+) Always Below 1 Ω
A25-2 (E) - Body ground Always Below 1 Ω
F1-12 (SW) - Body ground Always 10 kΩ or higher



c.

Reconnect the combination meter assembly connector and the brake fluid level warning switch.



OK

9.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the tester, read the Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light/OFF or ON OFF: Warning light off
ON: Warning light on
-


g.

When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List.


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Brake Warning Light Brake warning light Warning light OFF/ON Observe combination meter
[Vehicle condition]
Vehicle stopped

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF B
OFF Changes between ON and OFF A
Does not change between ON and OFF B

h.

Connect the intelligent tester to the DLC3.



A

10.REPLACE COMBINATION METER ASSEMBLY

B

11.CHECK COMBINATION METER ASSEMBLY
a.

Connect the intelligent tester to the DLC3.


b.

Perform Active Test of the combination meter assembly using the intelligent tester (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).

OK:

The brake warning light turns ON or OFF in accordance with the intelligent tester.




OK

END

NG

12.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.

Remove the parking brake switch assembly (See page Brake>PARKING BRAKE>PARKING BRAKE SWITCH>REMOVAL).


b.

Inspect the parking brake switch assembly (See page Brake>PARKING BRAKE>PARKING BRAKE SWITCH>INSPECTION).



OK

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - PARKING BRAKE SWITCH)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

13.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - PARKING BRAKE SWITCH)
a.

Disconnect the instrument panel junction block assembly connector and the parking brake switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-28 (PKB) - F22-1 Always Below 1 Ω
3A-28 (PKB) - Body ground Always 10 kΩ or higher



c.

Reconnect the instrument panel junction block assembly connector and the parking brake switch assembly connector.



OK

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-28 -12 (PKB) Always Below 1 Ω
3A-28 - Body ground Always 10 kΩ or higher



d.

Reconnect the instrument panel junction block assembly connector.


e.

Reinstall the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY