Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)
RM19S0E _54 Brake _051475 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0248235 VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)  C1275  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1413  Front Speed Sensor RH Output Malfunction  C1414  Front Speed Sensor LH Output Malfunction  


DESCRIPTION

Refer to DTCs C1401 and C1402 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>C1271).

DTC No. DTC Detection Condition Trouble Area
C1413
C1414
Any of the following is detected:
1.

An open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

2.

At a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

3.

At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Front speed sensor RH/LH

·

Speed sensor circuit

·

Speed sensor rotor

·

Skid control ECU (Brake actuator assembly)



Test Mode Diagnosis Code
DTC No. DTC Detection Condition Trouble Area
C1275
C1276
Detected only during Test Mode.
·

Front speed sensor RH/LH

·

Speed sensor rotor



HINT:
·

DTC C1413 and C1275 are for the front speed sensor RH.

·

DTC C1414 and C1276 are for the front speed sensor LH.



CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly, perform zero point calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>CALIBRATION).


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)

OK

2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)

NG

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)

OK

3.PERFORM TEST MODE (SIGNAL CHECK)

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check in the Test Mode procedure (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>TEST MODE PROCEDURE).

OK:

All Test Mode DTCs are cleared.




OK

4.RECONFIRM DTC

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
4.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Result
Result Proceed to
DTCs C1413 and C1414 are not output A
DTCs C1413 and/or C1414 are output B

HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



A

B

11.REPLACE FRONT SPEED SENSOR
6.INSPECT FRONT SPEED SENSOR TIP

OK

7.INSPECT FRONT SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

7.INSPECT FRONT SPEED SENSOR ROTOR
a.

Remove the front speed sensor and the front axle hub sub-assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).


b.

Check the speed sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning or replacement (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>TEST MODE PROCEDURE).


HINT:

If the front axle hub sub-assembly needs to be replaced, replace it together with the front drive outboard joint shaft assembly.



c.

Reinstall the front speed sensor and the front axle hub sub-assembly (See page Drivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>INSTALLATION).



OK

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR ROTOR

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

OK

9.INSPECT SKID CONTROL ECU (SENSOR INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Result
Result Proceed to
DTCs C1413 and/or C1414 are output A
DTCs C1413 and C1414 are not output B

HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



A

11.REPLACE FRONT SPEED SENSOR

B

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION)

11.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.




NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.



Result
Result Proceed to
DTCs C1413 and C1414 are not output A
DTCs C1413 and/or C1414 are output B

HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Separate Type Yaw Rate Sensor)>PROBLEM SYMPTOMS TABLE).



A

END

B

REPLACE FRONT SPEED SENSOR ROTOR