Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER(for RHD)
RM19S0E _54 Brake _051476 BRAKE SYSTEM (OTHER) _0248244 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  INSTALLATION  


PROCEDURE

Hide 44610 1.INSTALL BRAKE BOOSTER ASSEMBLY

a.

Install a new gasket onto the brake booster assembly.


b.

Temporary install the brake booster assembly with the 4 nuts.


c.
C233126E01
0.732,0.288 0.830,0.440 0.098,0.152 10 1 1.899,0.288 1.997,0.440 0.098,0.152 10 2 0.67,1.42 0.768,1.572 0.098,0.152 10 3 2.712,1.594 2.810,1.746 0.098,0.152 10 4

Tighten the 4 nuts as shown in the illustration.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


d.

Install the wire harness clamp.


e.

Connect the vacuum hose to the vacuum check valve with the clip.


Hide 47264D 2.INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS

a.

Install the push rod lock nut and brake master cylinder push rod clevis to the brake booster assembly.

HINT:

Tighten the push rod lock nut after adjusting the brake pedal height.



b.
C235059E01
0.452,1.864 0.646,2.038 0.194,0.174 10 *1

Apply lithium soap base glycol grease to the push rod pin.

Text in Illustration
*1 Lithium Soap Base Glycol Grease


c.

Install the brake master cylinder push rod clevis with the push rod pin and a new clip.


d.

Install the brake pedal return spring.


Hide 55711 3.INSTALL OUTER COWL TOP PANEL

a.

Install the outer cowl top panel with the 8 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


b.

Engage the 2 clamps and install the wire harness.


Hide 55722C 4.INSTALL INNER COWL TOP TO COWL BRACE

a.

Install the cowl top to cowl brace with the 2 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 55815E 5.INSTALL FRONT NO. 1 VENTILATOR SEAL

a.

Engage the clip and install the front No. 1 ventilator seal.


Hide 55735D 6.INSTALL FRONT AIR SHUTTER SEAL RH

HINT:

Use the same procedure as for the front No. 1 ventilator seal.


Hide 47201 7.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 85110 8.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 9.INSPECT AND ADJUST BRAKE PEDAL

Hide 55432B 10.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)

a.

for LHD:

i.

Engage the 5 claws and 2 clips and install the instrument panel finish panel.



b.

for RHD:

i.

Engage the 6 claws and 2 clips and install the instrument panel finish panel.



Hide 73900 11.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 55606 12.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY