This DTC is stored when a malfunction occurs in the speakers.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15C3 | A short is detected in the speaker output circuit. | ·
Speakers ·
Harness or connector ·
Navigation receiver assembly |
Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
Clear the DTCs (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
Check for DTCs (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR).
No DTCs are output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Disconnect the F130 and F131 navigation receiver assembly connectors.
Disconnect the G8 and H8 front No. 1 speaker assembly connectors.
Disconnect the F91 and F92 front No. 2 speaker assembly connectors.
Disconnect the I4 and J4 rear speaker assembly connectors.
Measure the resistance between each of the navigation receiver assembly and the front No. 2 speaker assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F130-1 (FR+) - F91-4 (+) | Always | Below 1 Ω |
| F130-5 (FR-) - F91-2 (-) | Always | Below 1 Ω |
| F130-2 (FL+) - F92-4 (+) | Always | Below 1 Ω |
| F130-6 (FL-) - F92-2 (-) | Always | Below 1 Ω |
Measure the resistance between each of the front No. 2 speaker assembly and front No. 1 speaker assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F91-3 (TWR+) - G8-1 | Always | Below 1 Ω |
| F91-1 (TWR-) - G8-2 | Always | Below 1 Ω |
| F92-3 (TWL+) - H8-1 | Always | Below 1 Ω |
| F92-1 (TWL-) - H8-2 | Always | Below 1 Ω |
Measure the resistance between each of the navigation receiver assembly and the rear speaker assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-1 (RR+) - I4-1 | Always | Below 1 Ω |
| F131-3 (RR-) - I4-2 | Always | Below 1 Ω |
| F131-2 (RL+) - J4-1 | Always | Below 1 Ω |
| F131-6 (RL-) - J4-2 | Always | Below 1 Ω |
Measure the resistance between each speaker assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G8-1 - Body ground | Always | 10 kΩ or higher |
| G8-2 - Body ground | Always | 10 kΩ or higher |
| H8-1 - Body ground | Always | 10 kΩ or higher |
| H8-2 - Body ground | Always | 10 kΩ or higher |
| F91-4 (+) - Body ground | Always | 10 kΩ or higher |
| F91-2 (-) - Body ground | Always | 10 kΩ or higher |
| F92-4 (+) - Body ground | Always | 10 kΩ or higher |
| F92-2 (-) - Body ground | Always | 10 kΩ or higher |
| I4-1 - Body ground | Always | 10 kΩ or higher |
| I4-2 - Body ground | Always | 10 kΩ or higher |
| J4-1 - Body ground | Always | 10 kΩ or higher |
| J4-2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL).
Inspect the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION).
OK
NG
Remove the rear speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).
Inspect the rear speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION).
OK
NG
Replace the front No. 2 speaker assembly with a known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>QUARTER TRIM SPEAKER>REMOVAL).
Check that the malfunction disappears.
Connect all the connectors that were disconnected to the front No. 2 speaker assemblies.
Perform the above inspection on both LH and RH sides.
Malfunction disappears.
OK
NG