Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › 2011.08–2014.07
RM19S0E _58 Vehicle Interior _051490 DOOR LOCK _0248290 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is in the LOCK or ACC positions. The key reminder warning buzzer is activated when the main body ECU sends a key switch signal and driver side courtesy light switch signal to the combination meter.

WIRING DIAGRAM

B445032E01
0.406,1.698 0.719,1.896 0.313,0.198 10 false K1 1.531,1.313 1.823,1.5 0.292,0.188 10 false 1 2.406,1.208 2.698,1.396 0.292,0.188 10 false 36 2.406,1.417 2.698,1.604 0.292,0.188 10 false 3D 3.625,1.417 3.917,1.604 0.292,0.188 10 false MB 3.688,1.219 3.844,1.406 0.156,0.188 10 false 2 4,1.427 4.385,1.625 0.385,0.198 10 false FLCY 4.344,0.615 4.708,0.792 0.365,0.177 10 false KSW 4.802,0.594 5.167,0.771 0.365,0.177 10 false F76 4.844,0.385 5.208,0.563 0.365,0.177 10 false 17 5.563,0.49 5.854,0.677 0.292,0.188 10 false 1 6.583,0.49 6.875,0.677 0.292,0.188 10 false 2 3.885,3.104 5,3.313 1.115,0.208 10 false Main Body ECU 5.635,2.927 6.906,3.313 1.271,0.385 10 false Combination Meter Assembly 5.604,0.906 5.969,1.083 0.365,0.177 10 false F15 5.604,1.063 6.854,1.438 1.25,0.375 10 false Unlock Warning Switch Assembly 2.292,2.052 3.979,2.417 1.688,0.365 10 false Instrument Panel Junction Block Assembly 0.406,1.865 2.094,2.229 1.688,0.365 10 false Front Door Courtesy Light Switch Assembly LH 0.615,3.375 2.417,3.594 1.802,0.219 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

HINT:

Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with How to Proceed with Troubleshooting. Then conduct the following troubleshooting procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FRONT DOOR COURTESY LIGHT SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FL Door Courtesy Front LH door courtesy light switch signal / ON or OFF ON: Front LH door closed
OFF: Front LH door opened
-

OK:

When the unlock warning switch is operated, the display changes as shown in the table.




OK

2.READ VALUE USING INTELLIGENT TESTER (KEY UNLOCK WARNING SW)

NG

GO TO LIGHTING SYSTEM (DOOR COURTESY LIGHT SWITCH CIRCUIT)

2.READ VALUE USING INTELLIGENT TESTER (KEY UNLOCK WARNING SW)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch signal / OFF or ON OFF: Ignition key is not inserted
ON: Ignition key is inserted
-

OK:

When the unlock warning switch is operated, the display changes as shown in the table.




OK

3.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)

NG

4.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
3.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)
a.

Remove the key from the key cylinder, turn the light control switch on the headlight dimmer switch assembly to the tail position, and open the driver door.

OK:

The light reminder warning buzzer sounds.


HINT:

The key reminder warning system sounds the buzzer built in to the combination meter for key reminder warnings. This buzzer is also used for the light reminder warning system. Therefore, check the operation of the combination meter buzzer by checking if the buzzer sounds to inform that the lights are still on.




OK

NG

REPLACE COMBINATION METER ASSEMBLY

4.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Inspect the unlock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION).



OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - UNLOCK WARNING SWITCH ASSEMBLY)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - UNLOCK WARNING SWITCH ASSEMBLY)
a.

Disconnect the F15 unlock warning switch and F76 main body ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F15-1 - F76-17 (KSW) Always Below 1 Ω
F15-2 - Body ground Always Below 1 Ω
F15-1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR