Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor) › 2011.08–2017.01
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248314 AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/ VSC/Built-in Type Yaw Rate Sensor)  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH (for 5 Door), door side airbag sensor RH (for 3 Door) and No. 2 side airbag sensor assembly RH.

The side airbag sensor assembly RH (for 5 Door), door side airbag sensor RH (for 3 Door) and No. 2 side airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

This DTC is stored when a malfunction is detected for the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).

DTC No. DTC Detection Condition Trouble Area
B1633/81
·

The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).

·

Side airbag sensor RH malfunction

·

No. 2 side airbag sensor assembly RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Front door wire RH

·

Side airbag sensor assembly RH (for 5 Door)

·

Door side airbag sensor RH (for 3 Door)

·

No. 2 side airbag sensor assembly RH

·

airbag sensor assembly



WIRING DIAGRAM

C241048E20
5.542,1.635 5.948,1.792 0.406,0.156 10 false BBR- 5.542,1.146 5.948,1.302 0.406,0.156 10 false BBR+ 5.25,1.052 5.438,1.198 0.188,0.146 10 false 17 5.25,1.563 5.438,1.708 0.188,0.146 10 false 18 1.344,2.667 1.75,2.823 0.406,0.156 10 false BDR+ 1.344,2.146 1.75,2.302 0.406,0.156 10 false BDR- 1.823,2.063 2.01,2.208 0.188,0.146 10 false 2 1.823,2.563 2.01,2.708 0.188,0.146 10 false 1 1.344,1.646 1.75,1.802 0.406,0.156 10 false BCR- 1.344,1.135 1.75,1.292 0.406,0.156 10 false BCR+ 1.823,1.042 2.01,1.188 0.188,0.146 10 false 4 1.823,1.552 2.01,1.698 0.188,0.146 10 false 3 3.365,2.667 3.677,2.823 0.313,0.156 10 false GK2 3.365,2.177 3.677,2.333 0.313,0.156 10 false GK2 3.479,1.969 3.667,2.135 0.188,0.167 10 false 2 3.479,2.469 3.667,2.646 0.188,0.177 10 false 1 1.354,5.052 1.76,5.208 0.406,0.156 10 false BDR- 1.354,4.51 1.76,4.667 0.406,0.156 10 false BDR+ 1.844,4.438 2.031,4.583 0.188,0.146 10 false 2 1.844,4.969 2.031,5.115 0.188,0.146 10 false 1 5.375,5.635 5.667,5.802 0.292,0.167 10 false K32 5.375,5.792 6.979,6.146 1.604,0.354 10 false Airbag Sensor Assembly 0.354,3.333 0.646,3.5 0.292,0.167 10 false K46 0.344,3.51 2.844,3.677 2.5,0.167 10 false No. 2 Side Airbag Sensor Assembly RH 0.354,5.646 0.646,5.813 0.292,0.167 10 false G16 0.365,5.802 2.51,5.969 2.146,0.167 10 false Door Side Airbag Sensor RH 0.188,0.146 1.01,0.333 0.823,0.188 12 false for 3 Door:

C241675E11
1.181,1.005 1.587,1.147 0.406,0.142 10 BBR+ 1.181,1.798 1.587,1.940 0.406,0.142 10 BBR- 5.693,1.005 6.099,1.147 0.406,0.142 10 BBR+ 5.693,1.798 6.099,1.940 0.406,0.142 10 BBR- 1.181,3.189 1.601,3.332 0.420,0.143 10 BCR+ 1.181,3.964 1.601,4.110 0.420,0.145 10 BCR- 3.892,3.186 4.309,3.336 0.416,0.150 10 BCR+ 3.892,3.968 4.274,4.106 0.382,0.139 10 BCR- 1.695,0.905 1.802,1.049 0.107,0.144 10 4 1.695,1.717 1.799,1.868 0.104,0.151 10 3 1.695,3.124 1.796,3.262 0.100,0.137 10 1 1.695,3.88 1.804,4.045 0.108,0.165 10 2 3.647,3.113 3.746,3.272 0.098,0.159 10 2 3.654,3.885 3.758,4.041 0.104,0.156 10 1 5.38,1.722 5.571,1.864 0.191,0.142 10 18 5.391,0.902 5.571,1.051 0.180,0.149 10 17 0.621,4.675 0.894,4.821 0.273,0.145 10 K22 3.759,4.689 4.026,4.852 0.267,0.163 10 K24 5.557,4.682 5.834,4.824 0.276,0.143 10 K32 0.621,4.836 2.764,4.975 2.143,0.139 10 Side Airbag Sensor Assembly RH 3.759,4.85 5.103,5.172 1.344,0.322 10 No. 2 Side Airbag Sensor Assembly RH 5.557,4.827 7.099,5.152 1.541,0.325 10 Airbag Sensor Assembly 0.131,0.08 0.953,0.277 0.823,0.198 12 for 5 Door:

PROCEDURE

1.SYSTEM CHECK
a.

Check the vehicle specifications.

Result
Result Proceed to
for 3 Door A
for 5 Door B



A

2.CHECK HISTORY DTC

B

18.CHECK FLOOR WIRE (OPEN)
2.CHECK HISTORY DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result:

History DTC B1632/81 or B1637/82 is not output.


HINT:

Codes other than history DTCs B1632/81 and B1637/82 may be output at this time, but they are not related to this check.




OK

3.CHECK CONNECTORS

NG

3.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.


e.

Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.




OK

4.CHECK FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

4.CHECK FLOOR WIRE (OPEN)
a.

Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

U158396E01
3.771,0.322 4.035,0.503 0.264,0.181 10 K32 0.248,1.337 0.418,1.498 0.170,0.161 10 *1 1.462,1.183 1.631,1.344 0.170,0.161 10 *2 0.888,0.605 1.057,0.766 0.170,0.161 10 *3 2.931,0.1 3.101,0.261 0.170,0.161 10 *a 5.255,0.1 5.425,0.261 0.170,0.161 10 *b 6.083,0.369 6.347,0.551 0.264,0.181 10 K46 2.931,0.334 3.101,0.494 0.170,0.161 10 *4 5.255,0.334 5.425,0.494 0.170,0.161 10 *5 0.91,1.152 1.035,1.304 0.125,0.152 10 C 1.197,1.152 1.308,1.304 0.111,0.152 10 B 1.562,0.978 1.676,1.130 0.114,0.152 10 A 0.526,0.978 0.651,1.130 0.125,0.152 10 D 2.938,1.176 3.323,1.329 0.385,0.152 10 BBR+ 3.985,1.316 4.339,1.469 0.354,0.152 10 BBR- 3.46,1.506 3.751,1.658 0.291,0.152 10 *6 6.357,1.325 6.759,1.478 0.402,0.152 10 BCR+ 5.845,1.325 6.251,1.478 0.406,0.152 10 BCR- 1.124,0.992 1.042,0.672 false 6.03,1.284 6.238,1.022 false 6.541,1.284 6.333,1.022 false 3.315,1.245 3.607,1.148 false 3.722,1.139 3.976,1.387 false 3.6,1.497 3.636,1.379 false

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH *2 Airbag Sensor Assembly
*3 Floor Wire *4 Connector B
*5 Connector C *6 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K46-3 (BCR-) - K46-4 (BCR+) Always Below 1 Ω




OK

5.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT)
a.
U158371E02
2.271,2.552 2.031,2.906 true 2.406,2.552 2.615,2.917 true 1.49,0.365 1.583,1.031 false 0.781,1.042 0.906,1.198 0.125,0.156 10 false D 1.281,1.25 1.406,1.406 0.125,0.156 10 false C 1.688,1.25 1.813,1.406 0.125,0.156 10 false B 2.198,1.031 2.323,1.188 0.125,0.156 10 false A 0.385,1.531 0.573,1.688 0.188,0.156 10 false *1 2.042,1.302 2.219,1.469 0.177,0.167 10 false *2 1.344,0.229 1.51,0.385 0.167,0.156 10 false *3 0.99,1.875 1.146,2.021 0.156,0.146 10 false *a 1.208,2.156 1.385,2.302 0.177,0.146 10 false *4 2.063,1.844 2.375,2.021 0.313,0.177 10 false K46 2.49,2.938 2.906,3.094 0.417,0.156 10 false BCR+ 1.771,2.948 2.146,3.104 0.375,0.156 10 false BCR-

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K46-3 (BCR-) - K46-4 (BCR+) Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Connector C
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)



OK

6.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (SHORT TO B+)
a.
U158371E02
2.271,2.552 2.031,2.906 true 2.406,2.552 2.615,2.917 true 1.49,0.365 1.583,1.031 false 0.781,1.042 0.906,1.198 0.125,0.156 10 false D 1.281,1.25 1.406,1.406 0.125,0.156 10 false C 1.688,1.25 1.813,1.406 0.125,0.156 10 false B 2.198,1.031 2.323,1.188 0.125,0.156 10 false A 0.385,1.531 0.573,1.688 0.188,0.156 10 false *1 2.042,1.302 2.219,1.469 0.177,0.167 10 false *2 1.344,0.229 1.51,0.385 0.167,0.156 10 false *3 0.99,1.875 1.146,2.021 0.156,0.146 10 false *a 1.208,2.156 1.385,2.302 0.177,0.146 10 false *4 2.063,1.844 2.375,2.021 0.313,0.177 10 false K46 2.49,2.938 2.906,3.094 0.417,0.156 10 false BCR+ 1.771,2.948 2.146,3.104 0.375,0.156 10 false BCR-

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K46-3 (BCR-) - Body ground Ignition switch ON Below 1 V
K46-4 (BCR+) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Connector C
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)



OK

7.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

7.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U158371E02
2.271,2.552 2.031,2.906 true 2.406,2.552 2.615,2.917 true 1.49,0.365 1.583,1.031 false 0.781,1.042 0.906,1.198 0.125,0.156 10 false D 1.281,1.25 1.406,1.406 0.125,0.156 10 false C 1.688,1.25 1.813,1.406 0.125,0.156 10 false B 2.198,1.031 2.323,1.188 0.125,0.156 10 false A 0.385,1.531 0.573,1.688 0.188,0.156 10 false *1 2.042,1.302 2.219,1.469 0.177,0.167 10 false *2 1.344,0.229 1.51,0.385 0.167,0.156 10 false *3 0.99,1.875 1.146,2.021 0.156,0.146 10 false *a 1.208,2.156 1.385,2.302 0.177,0.146 10 false *4 2.063,1.844 2.375,2.021 0.313,0.177 10 false K46 2.49,2.938 2.906,3.094 0.417,0.156 10 false BCR+ 1.771,2.948 2.146,3.104 0.375,0.156 10 false BCR-

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K46-3 (BCR-) - Body ground Always 1 MΩ or higher
K46-4 (BCR+) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Connector C
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)



OK

8.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (OPEN)

NG

REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (OPEN)
a.

Using the service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

U158398E01
5.503,0.942 5.783,1.123 0.280,0.181 10 G16 0.43,1.181 0.600,1.341 0.170,0.161 10 *1 1.975,1.17 2.145,1.331 0.170,0.161 10 *2 1.072,0.411 1.242,0.571 0.170,0.161 10 *3 5.602,0.15 5.772,0.311 0.170,0.161 10 *b 3.263,0.15 3.433,0.311 0.170,0.161 10 *a 3.185,0.943 3.449,1.124 0.264,0.181 10 K46 5.602,0.384 5.772,0.545 0.170,0.161 10 *6 3.263,0.384 3.433,0.545 0.170,0.161 10 *5 1.476,0.974 1.601,1.127 0.125,0.152 10 C 1.79,0.974 1.900,1.127 0.111,0.152 10 B 2.085,0.792 2.200,0.944 0.114,0.152 10 A 0.76,0.792 0.863,0.944 0.104,0.152 10 F 5.595,1.311 5.994,1.463 0.398,0.152 10 BDR- 6.642,1.451 7.052,1.603 0.409,0.152 10 BDR+ 6.198,1.479 6.489,1.631 0.291,0.152 10 *7 3.457,1.391 3.859,1.543 0.402,0.152 10 BDR+ 3.961,1.391 4.367,1.543 0.406,0.152 10 BDR- 1.305,0.797 1.226,0.477 false 3.642,1.357 3.85,1.095 false 4.152,1.357 3.944,1.095 false 5.986,1.378 6.356,1.077 false 6.487,1.086 6.818,1.437 false 6.338,1.471 6.374,1.353 false 1.372,0.974 1.497,1.127 0.125,0.152 10 D 1.064,0.974 1.189,1.127 0.125,0.152 10 E 1.701,0.797 1.622,0.477 false 1.451,0.411 1.620,0.571 0.170,0.161 10 *4

Text in Illustration
*1 Door Side Airbag Sensor RH *2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH *4 Floor Wire
*5 Connector B *6 Connector E
*7 Service Wire - -
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Door Side Airbag Sensor RH)

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K46-1 (BDR+) - K46-2 (BDR-) Always Below 1 Ω




OK

9.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT)

NG

14.CHECK FRONT DOOR WIRE RH (OPEN)
9.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT)
a.
U158406E02
2.031,2.552 1.792,2.927 true 2.177,2.552 2.365,2.917 true 1.531,0.542 1.51,0.896 false 2.01,0.531 1.979,0.885 false 0.906,0.885 1.01,1.042 0.104,0.156 10 false F 1.76,1.115 1.885,1.271 0.125,0.156 10 false C 2.135,1.115 2.26,1.271 0.125,0.156 10 false B 2.479,0.875 2.604,1.031 0.125,0.156 10 false A 0.49,1.375 0.677,1.531 0.188,0.156 10 false *1 2.365,1.354 2.542,1.521 0.177,0.167 10 false *2 1.552,0.438 1.719,0.594 0.167,0.156 10 false *3 0.771,1.75 0.927,1.896 0.156,0.146 10 false *a 0.927,2.01 1.104,2.156 0.177,0.146 10 false *5 1.01,2.479 1.292,2.635 0.281,0.156 10 false K46 2.198,2.948 2.573,3.104 0.375,0.156 10 false BDR- 1.552,2.948 1.958,3.104 0.406,0.156 10 false BDR+ 2.042,0.438 2.219,0.583 0.177,0.146 10 false *4 1.625,1.115 1.75,1.271 0.125,0.156 10 false D 1.26,1.115 1.385,1.271 0.125,0.156 10 false E

Disconnect the service wire from connector E.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K46-1 (BDR+) - K46-2 (BDR-) Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector B
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)



OK

10.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT TO B+)

NG

15.CHECK FRONT DOOR WIRE RH (SHORT)
10.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT TO B+)
a.
U158406E02
2.031,2.552 1.792,2.927 true 2.177,2.552 2.365,2.917 true 1.531,0.542 1.51,0.896 false 2.01,0.531 1.979,0.885 false 0.906,0.885 1.01,1.042 0.104,0.156 10 false F 1.76,1.115 1.885,1.271 0.125,0.156 10 false C 2.135,1.115 2.26,1.271 0.125,0.156 10 false B 2.479,0.875 2.604,1.031 0.125,0.156 10 false A 0.49,1.375 0.677,1.531 0.188,0.156 10 false *1 2.365,1.354 2.542,1.521 0.177,0.167 10 false *2 1.552,0.438 1.719,0.594 0.167,0.156 10 false *3 0.771,1.75 0.927,1.896 0.156,0.146 10 false *a 0.927,2.01 1.104,2.156 0.177,0.146 10 false *5 1.01,2.479 1.292,2.635 0.281,0.156 10 false K46 2.198,2.948 2.573,3.104 0.375,0.156 10 false BDR- 1.552,2.948 1.958,3.104 0.406,0.156 10 false BDR+ 2.042,0.438 2.219,0.583 0.177,0.146 10 false *4 1.625,1.115 1.75,1.271 0.125,0.156 10 false D 1.26,1.115 1.385,1.271 0.125,0.156 10 false E

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K46-1 (BDR+) - Body ground Ignition switch ON Below 1 V
K46-2 (BDR-) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector B
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)



OK

11.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT TO GROUND)

NG

16.CHECK FRONT DOOR WIRE RH (SHORT TO B+)
11.CHECK FLOOR WIRE AND FRONT DOOR WIRE RH (SHORT TO GROUND)
a.
U158406E02
2.031,2.552 1.792,2.927 true 2.177,2.552 2.365,2.917 true 1.531,0.542 1.51,0.896 false 2.01,0.531 1.979,0.885 false 0.906,0.885 1.01,1.042 0.104,0.156 10 false F 1.76,1.115 1.885,1.271 0.125,0.156 10 false C 2.135,1.115 2.26,1.271 0.125,0.156 10 false B 2.479,0.875 2.604,1.031 0.125,0.156 10 false A 0.49,1.375 0.677,1.531 0.188,0.156 10 false *1 2.365,1.354 2.542,1.521 0.177,0.167 10 false *2 1.552,0.438 1.719,0.594 0.167,0.156 10 false *3 0.771,1.75 0.927,1.896 0.156,0.146 10 false *a 0.927,2.01 1.104,2.156 0.177,0.146 10 false *5 1.01,2.479 1.292,2.635 0.281,0.156 10 false K46 2.198,2.948 2.573,3.104 0.375,0.156 10 false BDR- 1.552,2.948 1.958,3.104 0.406,0.156 10 false BDR+ 2.042,0.438 2.219,0.583 0.177,0.146 10 false *4 1.625,1.115 1.75,1.271 0.125,0.156 10 false D 1.26,1.115 1.385,1.271 0.125,0.156 10 false E

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K46-1 (BDR+) - Body ground Always 1 MΩ or higher
K46-2 (BDR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector B
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)



OK

12.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY RH

NG

17.CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)
12.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C235513E01
0.651,1.683 0.821,1.843 0.170,0.161 10 *1 1.745,1.468 1.914,1.628 0.170,0.161 10 *2

Connect the connectors to the door side airbag sensor RH and airbag sensor assembly.


b.

Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1633/81 is output. A
DTC B1638/82 is output. B
DTC B1633/81 or B1638/82 is not output. C

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly

HINT:

Codes other than DTCs B1633/81 and B1638/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the No. 2 side airbag sensor assembly RH and the No. 2 side airbag sensor assembly LH to their original positions and connect the connectors to them.



A

13.CHECK DOOR SIDE AIRBAG SENSOR RH

B

C

13.CHECK DOOR SIDE AIRBAG SENSOR RH
a.
C195583E03
0.403,1.497 0.558,1.652 0.155,0.155 10 *1 2.176,1.497 2.331,1.652 0.155,0.155 10 *2

Interchange the door side airbag sensor RH with the door side airbag sensor LH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1633/81 or B1638/82 is not output. A
DTC B1633/81 is output. B
DTC B1638/82 is output. C

Text in Illustration
*1 Door Side Airbag Sensor LH
*2 No. 2 Side Airbag Sensor Assembly RH

HINT:

Codes other than DTCs B1633/81 and B1638/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the door side airbag sensor LH and the door side airbag sensor RH to their original positions and connect the connectors to them.



A

B

C

14.CHECK FRONT DOOR WIRE RH (OPEN)
a.

Disconnect the floor wire connector from the front door wire RH.

U158402E01
4.957,0.942 5.237,1.123 0.280,0.181 10 G16 0.444,1.181 0.614,1.341 0.170,0.161 10 *1 2.101,1.17 2.271,1.331 0.170,0.161 10 *2 1.1,0.411 1.270,0.571 0.170,0.161 10 *3 5.07,0.15 5.240,0.311 0.170,0.161 10 *b 3.291,0.15 3.461,0.311 0.170,0.161 10 *a 3.279,0.862 3.576,1.043 0.297,0.181 10 GK2 5.07,0.384 5.240,0.545 0.170,0.161 10 *6 3.291,0.384 3.461,0.545 0.170,0.161 10 *5 1.602,0.974 1.727,1.127 0.125,0.152 10 C 1.916,0.974 2.026,1.127 0.111,0.152 10 B 2.211,0.792 2.326,0.944 0.114,0.152 10 A 0.788,0.792 0.891,0.944 0.104,0.152 10 F 5.07,1.311 5.450,1.463 0.380,0.152 10 BDR- 6.117,1.451 6.531,1.603 0.414,0.152 10 BDR+ 5.672,1.479 5.964,1.631 0.291,0.152 10 *7 3.653,1.489 4.055,1.641 0.402,0.152 10 BDR+ 4.158,1.489 4.564,1.641 0.406,0.152 10 BDR- 1.333,0.797 1.254,0.477 false 3.838,1.455 4.046,1.193 false 4.348,1.455 4.14,1.193 false 5.46,1.378 5.831,1.077 false 5.962,1.086 6.293,1.437 false 5.812,1.471 5.848,1.353 false 1.401,0.974 1.525,1.127 0.125,0.152 10 D 1.092,0.974 1.217,1.127 0.125,0.152 10 E 1.827,0.797 1.748,0.477 false 1.577,0.411 1.747,0.571 0.170,0.161 10 *4

Text in Illustration
*1 Door Side Airbag Sensor RH *2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH *4 Floor Wire
*5 Connector D *6 Connector E
*7 Service Wire - -
*a Front view of wire harness connector
(to Floor Wire)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)

HINT:

The service wire has already been inserted into connector E.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GK2-1 (BDR+) - GK2-2 (BDR-) Always Below 1 Ω




OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

15.CHECK FRONT DOOR WIRE RH (SHORT)
a.
C355221E01
1.198,2.469 1.531,2.698 0.333,0.229 1.458,0.948 1.625,0.5 false 1.844,0.948 2.01,0.5 false 1.677,3.01 1.927,2.708 true 2.271,2.99 2.094,2.708 true 0.969,0.927 1.125,1.125 0.156,0.198 10 false F 1.281,1.156 1.438,1.354 0.156,0.198 10 false E 1.531,1.146 1.688,1.344 0.156,0.198 10 false D 1.677,1.146 1.833,1.344 0.156,0.198 10 false C 1.938,1.146 2.094,1.344 0.156,0.198 10 false B 2.25,0.917 2.406,1.115 0.156,0.198 10 false A 1.656,0.385 1.833,0.583 0.177,0.198 10 false *3 2.063,0.375 2.24,0.573 0.177,0.198 10 false *4 0.635,1.406 0.813,1.604 0.177,0.198 10 false *1 2.104,1.396 2.281,1.594 0.177,0.198 10 false *2 1.083,1.854 1.26,2.052 0.177,0.198 10 false *a 1.26,2.156 1.438,2.354 0.177,0.198 10 false *5 1.229,2.5 1.563,2.698 0.333,0.198 10 false GK2 1.458,3.031 1.865,3.229 0.406,0.198 10 false BDR+ 2.188,3.031 2.594,3.229 0.406,0.198 10 false BDR-

Disconnect the floor wire connector from the front door wire RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GK2-1 (BDR+) - GK2-2 (BDR-) Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector D
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

16.CHECK FRONT DOOR WIRE RH (SHORT TO B+)
a.

Turn the ignition switch off.


b.
C355221E01
1.198,2.469 1.531,2.698 0.333,0.229 1.458,0.948 1.625,0.5 false 1.844,0.948 2.01,0.5 false 1.677,3.01 1.927,2.708 true 2.271,2.99 2.094,2.708 true 0.969,0.927 1.125,1.125 0.156,0.198 10 false F 1.281,1.156 1.438,1.354 0.156,0.198 10 false E 1.531,1.146 1.688,1.344 0.156,0.198 10 false D 1.677,1.146 1.833,1.344 0.156,0.198 10 false C 1.938,1.146 2.094,1.344 0.156,0.198 10 false B 2.25,0.917 2.406,1.115 0.156,0.198 10 false A 1.656,0.385 1.833,0.583 0.177,0.198 10 false *3 2.063,0.375 2.24,0.573 0.177,0.198 10 false *4 0.635,1.406 0.813,1.604 0.177,0.198 10 false *1 2.104,1.396 2.281,1.594 0.177,0.198 10 false *2 1.083,1.854 1.26,2.052 0.177,0.198 10 false *a 1.26,2.156 1.438,2.354 0.177,0.198 10 false *5 1.229,2.5 1.563,2.698 0.333,0.198 10 false GK2 1.458,3.031 1.865,3.229 0.406,0.198 10 false BDR+ 2.188,3.031 2.594,3.229 0.406,0.198 10 false BDR-

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the front door wire connector from the floor wire.


d.

Connect the cable to the negative (-) battery terminal.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
GK2-1 (BDR+) - Body ground Ignition switch ON Below 1 V
GK2-2 (BDR-) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector D
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

17.CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)
a.
C355221E01
1.198,2.469 1.531,2.698 0.333,0.229 1.458,0.948 1.625,0.5 false 1.844,0.948 2.01,0.5 false 1.677,3.01 1.927,2.708 true 2.271,2.99 2.094,2.708 true 0.969,0.927 1.125,1.125 0.156,0.198 10 false F 1.281,1.156 1.438,1.354 0.156,0.198 10 false E 1.531,1.146 1.688,1.344 0.156,0.198 10 false D 1.677,1.146 1.833,1.344 0.156,0.198 10 false C 1.938,1.146 2.094,1.344 0.156,0.198 10 false B 2.25,0.917 2.406,1.115 0.156,0.198 10 false A 1.656,0.385 1.833,0.583 0.177,0.198 10 false *3 2.063,0.375 2.24,0.573 0.177,0.198 10 false *4 0.635,1.406 0.813,1.604 0.177,0.198 10 false *1 2.104,1.396 2.281,1.594 0.177,0.198 10 false *2 1.083,1.854 1.26,2.052 0.177,0.198 10 false *a 1.26,2.156 1.438,2.354 0.177,0.198 10 false *5 1.229,2.5 1.563,2.698 0.333,0.198 10 false GK2 1.458,3.031 1.865,3.229 0.406,0.198 10 false BDR+ 2.188,3.031 2.594,3.229 0.406,0.198 10 false BDR-

Disconnect the front door wire connector from the floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GK2-1 (BDR+) - Body ground Always 1 MΩ or higher
GK2-2 (BDR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Door Side Airbag Sensor RH
*2 No. 2 Side Airbag Sensor Assembly RH
*3 Front Door Wire RH
*4 Floor Wire
*5 Connector D
*a Front view of wire harness connector
(to Floor Wire)



OK

REPLACE FLOOR WIRE

NG

REPLACE FRONT DOOR WIRE RH

18.CHECK FLOOR WIRE (OPEN)
a.

Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

U158363E02
6.469,1.729 6.729,1.906 true 6.344,1.729 6.063,1.948 true 3.844,1.729 3.604,1.969 true 3.948,1.729 4.24,1.958 true 1.188,0.667 1.26,1.167 false 6.271,2.375 6.406,2.115 false 0.625,1.156 0.75,1.313 0.125,0.156 10 false D 1.021,1.344 1.146,1.5 0.125,0.156 10 false C 1.354,1.344 1.479,1.5 0.125,0.156 10 false B 1.771,1.156 1.896,1.313 0.125,0.156 10 false A 0.292,1.563 0.479,1.719 0.188,0.156 10 false *1 2.75,0.427 2.948,0.583 0.198,0.156 10 false *a 5.146,0.427 5.302,0.594 0.156,0.167 10 false *b 5.24,1.094 5.406,1.24 0.167,0.146 10 false *5 5.698,1.927 6.083,2.083 0.385,0.156 10 false BCR- 6.656,1.927 7.094,2.083 0.438,0.156 10 false BCR+ 5.219,1.469 5.521,1.625 0.302,0.156 10 false K24 2.948,1.094 3.115,1.24 0.167,0.146 10 false *4 2.927,1.469 3.24,1.625 0.313,0.156 10 false K22 6.135,2.365 6.427,2.521 0.292,0.156 10 false *6 4.281,1.927 4.677,2.083 0.396,0.156 10 false BCR- 3.208,1.927 3.615,2.083 0.406,0.156 10 false BCR+ 1.042,0.542 1.229,0.698 0.188,0.156 10 false *3 1.667,1.563 1.823,1.75 0.156,0.188 10 false *2

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH *2 Side Airbag Sensor Assembly RH
*3 Floor Wire *4 Connector B
*5 Connector C *6 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH)

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-1 (BCR+) - K22-2 (BCR-) Always Below 1 Ω




OK

19.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

19.CHECK FLOOR WIRE (SHORT)
a.
U158372E02
2.031,2.563 1.75,2.896 true 2.177,2.563 2.427,2.885 true 1.656,0.281 1.75,0.896 false 0.979,0.865 1.104,1.021 0.125,0.156 10 false D 1.469,1.094 1.594,1.25 0.125,0.156 10 false C 1.865,1.094 1.99,1.25 0.125,0.156 10 false B 2.385,0.865 2.51,1.021 0.125,0.156 10 false A 0.573,1.365 0.76,1.521 0.188,0.156 10 false *1 1.042,1.771 1.24,1.927 0.198,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.521 1.427,2.677 0.271,0.156 10 false K22 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCR- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCR+ 1.49,0.167 1.677,0.323 0.188,0.156 10 false *3 2.198,1.365 2.354,1.552 0.156,0.188 10 false *2

Disconnect the service wire from connector C.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-1 (BCR+) - K22-2 (BCR-) Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

20.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

20.CHECK FLOOR WIRE (SHORT TO B+)
a.
U158372E02
2.031,2.563 1.75,2.896 true 2.177,2.563 2.427,2.885 true 1.656,0.281 1.75,0.896 false 0.979,0.865 1.104,1.021 0.125,0.156 10 false D 1.469,1.094 1.594,1.25 0.125,0.156 10 false C 1.865,1.094 1.99,1.25 0.125,0.156 10 false B 2.385,0.865 2.51,1.021 0.125,0.156 10 false A 0.573,1.365 0.76,1.521 0.188,0.156 10 false *1 1.042,1.771 1.24,1.927 0.198,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.521 1.427,2.677 0.271,0.156 10 false K22 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCR- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCR+ 1.49,0.167 1.677,0.323 0.188,0.156 10 false *3 2.198,1.365 2.354,1.552 0.156,0.188 10 false *2

Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K22-1 (BCR+) - Body ground Ignition switch ON Below 1 V
K22-2 (BCR-) - Body ground Ignition switch ON Below 1 V


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

21.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

21.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U158372E02
2.031,2.563 1.75,2.896 true 2.177,2.563 2.427,2.885 true 1.656,0.281 1.75,0.896 false 0.979,0.865 1.104,1.021 0.125,0.156 10 false D 1.469,1.094 1.594,1.25 0.125,0.156 10 false C 1.865,1.094 1.99,1.25 0.125,0.156 10 false B 2.385,0.865 2.51,1.021 0.125,0.156 10 false A 0.573,1.365 0.76,1.521 0.188,0.156 10 false *1 1.042,1.771 1.24,1.927 0.198,0.156 10 false *a 1.198,2.208 1.365,2.354 0.167,0.146 10 false *4 1.156,2.521 1.427,2.677 0.271,0.156 10 false K22 2.448,2.906 2.844,3.063 0.396,0.156 10 false BCR- 1.354,2.906 1.76,3.063 0.406,0.156 10 false BCR+ 1.49,0.167 1.677,0.323 0.188,0.156 10 false *3 2.198,1.365 2.354,1.552 0.156,0.188 10 false *2

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K22-1 (BCR+) - Body ground Always 1 MΩ or higher
K22-2 (BCR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Connector B
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)



OK

22.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

22.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C235513E01
0.651,1.683 0.821,1.843 0.170,0.161 10 *1 1.745,1.468 1.914,1.628 0.170,0.161 10 *2

Connect the connectors to the No. 2 side airbag sensor assembly RH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1633/81 is output. A
DTC B1638/82 is output. B
DTC B1633/81 or B1638/82 is not output. C

Text in Illustration
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly

HINT:

Codes other than DTCs B1633/81 and B1638/82 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and the side airbag sensor assembly LH to their original positions and connect the connectors to them.



A

23.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY RH

B

C

23.CHECK NO.2 SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C166174E16
1.099,1.369 1.276,1.538 0.177,0.169 10 *1 2.194,1.369 2.366,1.538 0.172,0.169 10 *2

Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1633/81 or B1638/82 is not output. A
DTC B1633/81 is output. B
DTC B1638/82 is output. C

Text in Illustration
*1 No. 2 Side Airbag Sensor Assembly LH
*2 Side Airbag Sensor Assembly RH

HINT:

Codes other than DTCs B1633/81 and B1638/82 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.



A

B

C