The side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH (for 5 Door), door side airbag sensor RH (for 3 Door) and No. 2 side airbag sensor assembly RH.
The side airbag sensor assembly RH (for 5 Door), door side airbag sensor RH (for 3 Door) and No. 2 side airbag sensor assembly RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.
This DTC is stored when a malfunction is detected for the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1642/81 | ·
The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH). ·
Side airbag sensor assembly RH malfunction (for 5 Door) ·
Door side airbag sensor RH malfunction (for 3 Door) ·
No. 2 side airbag sensor assembly RH malfunction ·
Airbag sensor assembly malfunction |
·
Floor wire ·
Front door wire RH ·
Side airbag sensor assembly RH (for 5 Door) ·
Door side airbag sensor RH (for 3 Door) ·
No. 2 side airbag sensor assembly RH ·
Airbag sensor assembly |
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for 3 Door | A |
| for 5 Door | B |
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly, door side airbag sensor RH and No. 2 side airbag sensor assembly RH.
Check that the terminals of connectors are not damaged.
The terminals are not deformed or damaged.
OK
NG
Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.
| *1 | No. 2 Side Airbag Sensor Assembly RH | *2 | Airbag Sensor Assembly |
| *3 | Floor Wire | *4 | Connector B |
| *5 | Connector C | *6 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
*b | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K46-3 (BCR-) - K46-4 (BCR+) | Always | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K46-3 (BCR-) - K46-4 (BCR+) | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
OK
NG
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K46-3 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
| K46-4 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K46-3 (BCR-) - Body ground | Always | 1 MΩ or higher |
| K46-4 (BCR+) - Body ground | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | Floor Wire |
| *4 | Connector C |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
OK
NG
Using the service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.
| *1 | Door Side Airbag Sensor RH | *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH | *4 | Floor Wire |
| *5 | Connector B | *6 | Connector E |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
*b | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K46-1 (BDR+) - K46-2 (BDR-) | Always | Below 1 Ω |
OK
NG
Disconnect the service wire from connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K46-1 (BDR+) - K46-2 (BDR-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
OK
NG
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K46-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| K46-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K46-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| K46-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector B |
| *a | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
OK
NG
Connect the connectors to the door side airbag sensor RH and airbag sensor assembly.
Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1642/81 is output. | A |
| DTC B1647/82 is output. | B |
| DTC B1642/81 or B1647/82 is not output. | C |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor assembly RH and the No. 2 side airbag sensor assembly LH to their original positions and connect the connectors to them.
A
B
C
Interchange the door side airbag sensor RH with the door side airbag sensor LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1642/81 or B1647/82 is not output. | A |
| DTC B1642/81 is output. | B |
| DTC B1647/82 is output. | C |
| *1 | Door Side Airbag Sensor LH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the door side airbag sensor LH and the door side airbag sensor RH to their original positions and connect the connectors to them.
A
B
C
Disconnect the floor wire connector from the front door wire RH.
| *1 | Door Side Airbag Sensor RH | *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH | *4 | Floor Wire |
| *5 | Connector D | *6 | Connector E |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Floor Wire) |
*b | Front view of wire harness connector
(to Door Side Airbag Sensor RH) |
The service wire has already been inserted into connector E.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GK2-1 (BDR+) - GK2-2 (BDR-) | Always | Below 1 Ω |
OK
NG
Disconnect the floor wire connector from the front door wire RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GK2-1 (BDR+) - GK2-2 (BDR-) | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector
(to Floor Wire) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect the front door wire connector from the floor wire.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| GK2-1 (BDR+) - Body ground | Ignition switch ON | Below 1 V |
| GK2-2 (BDR-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector
(to Floor Wire) |
OK
NG
Disconnect the front door wire connector from the floor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| GK2-1 (BDR+) - Body ground | Always | 1 MΩ or higher |
| GK2-2 (BDR-) - Body ground | Always | 1 MΩ or higher |
| *1 | Door Side Airbag Sensor RH |
| *2 | No. 2 Side Airbag Sensor Assembly RH |
| *3 | Front Door Wire RH |
| *4 | Floor Wire |
| *5 | Connector D |
| *a | Front view of wire harness connector
(to Floor Wire) |
OK
NG
Using the service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.
| *1 | No. 2 Side Airbag Sensor Assembly RH | *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire | *4 | Connector B |
| *5 | Connector C | *6 | Service Wire |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
*b | Front view of wire harness connector
(to No. 2 Side Airbag Sensor Assembly RH) |
Do not forcibly insert the service wire into the terminals of the connector when connecting.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-1 (BCR+) - K22-2 (BCR-) | Always | Below 1 Ω |
OK
NG
Disconnect the service wire from connector C.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-1 (BCR+) - K22-2 (BCR-) | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| K22-1 (BCR+) - Body ground | Ignition switch ON | Below 1 V |
| K22-2 (BCR-) - Body ground | Ignition switch ON | Below 1 V |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K22-1 (BCR+) - Body ground | Always | 1 MΩ or higher |
| K22-2 (BCR-) - Body ground | Always | 1 MΩ or higher |
| *1 | No. 2 Side Airbag Sensor Assembly RH |
| *2 | Side Airbag Sensor Assembly RH |
| *3 | Floor Wire |
| *4 | Connector B |
| *a | Front view of wire harness connector
(to Side Airbag Sensor Assembly RH) |
OK
NG
Connect the connectors to the No. 2 side airbag sensor assembly RH and airbag sensor assembly.
Interchange the side airbag sensor assembly RH with the side airbag sensor assembly LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1642/81 is output. | A |
| DTC B1647/82 is output. | B |
| DTC B1642/81 or B1647/82 is not output. | C |
| *1 | Side Airbag Sensor Assembly LH |
| *2 | Airbag Sensor Assembly |
Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the side airbag sensor assembly RH and the side airbag sensor assembly LH to their original positions and connect the connectors to them.
A
B
C
Interchange the No. 2 side airbag sensor assembly RH with the No. 2 side airbag sensor assembly LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1642/81 or B1647/82 is not output. | A |
| DTC B1642/81 is output. | B |
| DTC B1647/82 is output. | C |
| *1 | No. 2 Side Airbag Sensor Assembly LH |
| *2 | Side Airbag Sensor Assembly RH |
Codes other than DTCs B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Return the No. 2 side airbag sensor assembly LH and the No. 2 side airbag sensor assembly RH to their original positions and connect the connectors to them.
A
B
C