Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR(for 3 Door)
RM19S0E _58 Vehicle Interior _051495 SUPPLEMENTAL RESTRAINT SYSTEMS _0248329 REAR AIRBAG SENSOR(for 3 Door) A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR(for 3 Door)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (w/ VSC/Built-in Type Yaw Rate Sensor)>PRECAUTION).


HINT:

The procedure described below is for the RH side. Use the same procedure for both the LH and RH sides, unless otherwise specified.


PROCEDURE

Hide 89860C 1.INSTALL NO. 2 SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Insert the pin (stopper) into the body hole to install the No. 2 side airbag sensor assembly to the vehicle with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the No. 2 side airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the No. 2 side airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the pin (stopper) is securely inserted into the body hole.

·

Tighten the bolt while holding the No. 2 side airbag sensor assembly because the No. 2 side airbag sensor assembly pin (stopper) is easily damaged.




d.

Connect the connector to the No. 2 side airbag sensor assembly.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Connect the connector as shown in the illustration (when locking, make sure that the outer connector locking sleeve returns to its original position and a click sound can be heard).

C198070E06
3.541,1.785 3.877,1.949 0.336,0.164 10 *a 3.868,2.097 4.054,2.245 0.186,0.148 10 *1 3.945,1.31 3.945,2.083 false 5.794,1.637 5.794,2.083 false 5.699,2.102 5.886,2.25 0.186,0.148 10 *1

Text in Illustration
*1 Outer Connector Locking Sleeve - -
*a Slide - -

HINT:

When connected, the outer connector locking sleeve will slide. Be sure not to hold the outer connector locking sleeve while connecting, as it may result in an insecure fit.




e.

Check that there is no looseness in the installation parts of the No. 2 side airbag sensor assembly.


Hide 64730C 2.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)

Hide 64740C 3.INSTALL ROOF SIDE INNER GARNISH LH (for LH Side)

Hide 73360 4.DISCONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY

Hide 73201C 6.INSTALL FRONT SEAT BELT OUTER BAR SUB-ASSEMBLY

Hide 62313D 7.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 09113 10.INSTALL JACK HANDLE (for RH Side)

Hide 81250 11.INSTALL NO. 2 ROOM LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)

Hide 14.INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)

Hide 15.INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type LH Side)

Hide 16.INSTALL REAR SEAT ASSEMBLY (for 60/40 Split Seat Type RH Side)

Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)