Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0420  Catalyst System Efficiency Below Threshold (Bank 1)  


MONITOR DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.

The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.

In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.

The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.

The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and stores the DTC.

This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value.

DTC No. DTC Detection Condition Trouble Area
P0420 The oxygen storage capacity value is less than the standard value under active air fuel ratio control (1 trip detection logic).
·

Gas leak from exhaust system

·

Air fuel ratio sensor (bank 1 sensor 1)

·

Heated oxygen sensor (bank 1 sensor 2)

·

Front exhaust pipe assembly (TWC: Front catalyst and rear catalyst)



CATALYST LOCATION

A257619C01
0.637,0.427 0.802,0.606 0.165,0.179 10 *1 0.542,0.912 0.641,0.592 false 1.995,0.72 2.160,0.899 0.165,0.179 10 *2 1.968,0.813 1.767,0.885 false 2.979,4.374 3.281,4.344 false 3.33,4.283 3.495,4.462 0.165,0.179 10 *4 5.549,1.006 5.71,1.153 false 5.691,1.173 5.856,1.352 0.165,0.179 10 *5 0.603,2.764 0.768,2.943 0.165,0.179 10 *3 2.034,2.939 2.236,3.118 0.202,0.179 10 *6 1.73,3.249 2.012,3.034 false 2.741,2.972 2.943,3.151 0.202,0.179 10 *7 2.586,3.394 2.731,3.096 false 0.786,2.82 1.012,2.82 false
*1 Exhaust Manifold Assembly *2 Air Fuel Ratio Sensor
*3 Front Exhaust Pipe Assembly *4 Heated Oxygen Sensor
*5 Tail Exhaust Pipe Assembly *6 TWC: Front Catalyst
*7 TWC: Rear Catalyst - -


MONITOR STRATEGY

Related DTCs P0420: Catalyst Deterioration
Required Sensors/Components (Main) Air fuel ratio sensor
Heated oxygen sensor
Required Sensors/Components (Related) Intake air temperature sensor
Mass air flow meter
Crankshaft position sensor
Engine coolant temperature sensor
Frequency of Operation Once per driving cycle
Duration Approximately 30 seconds
MIL Operation 1 driving cycle
Sequence of Operation None

TYPICAL ENABLING CONDITIONS

Accumulated time that all of following conditions are met 30 seconds
Battery voltage 11 V or more
Intake air temperature -10°C (14°F) or more
Idle status OFF
Engine speed Less than 4000 rpm
Engine coolant temperature 75°C (167°F) or more
Fuel system status Closed loop
Front catalyst temperature 665°C (1229°F) or more
Rear catalyst temperature 520°C (968°F) or more

CONFIRMATION DRIVING PATTERN

HINT:
·

It is necessary that the response of the heated oxygen sensor is normal in order to confirm DTC P0420. Therefore, perform the driving pattern for the heated oxygen sensor monitor before performing the drive pattern for the catalyst efficiency monitor.

·

Perform this confirmation driving pattern will activate the catalyst monitor. this is very useful for verifying the completion of a repair.



U134191E04
1.281,4.667 1.563,4.385 1.563,4.385 1.667,4.385 false 0.26,0.635 1.208,0.792 0.948,0.156 10 false Vehicle Speed 0.094,1.177 1.25,1.354 1.156,0.177 10 false 60 km/h (37 mph) 0.865,2.146 1.271,2.333 0.406,0.188 10 false Idling 0.094,2.406 1.24,2.583 1.146,0.177 10 false Ignition Switch off 0.125,0.094 3.833,0.333 3.708,0.24 10 false Heated Oxygen Sensor Monitor Driving Pattern 0.125,3.573 2.844,3.802 2.719,0.229 10 false Catalyst Efficiency Monitor Driving Pattern 0.104,4.958 1.26,5.135 1.156,0.177 10 false 60 km/h (37 mph) 1.729,4.302 4.646,4.51 2.917,0.208 10 false Between 75 and 100 km/h (47 and 63 mph) 1.573,2.719 2.344,2.906 0.771,0.188 10 false Warming up 2.635,2.698 3.875,2.885 1.24,0.188 10 false 10 minutes or more 5.448,6.521 6.688,6.708 1.24,0.188 10 false 10 minutes or more 2.917,6.5 4.156,6.688 1.24,0.188 10 false 10 minutes or more 1.833,2.052 2.063,2.229 0.229,0.177 10 false [A] 3.135,0.969 3.625,1.146 0.49,0.177 10 false [B]* 4.281,0.969 4.51,1.146 0.229,0.177 10 false [C] 5.271,0.969 5.5,1.146 0.229,0.177 10 false [C] 6.25,0.969 6.479,1.146 0.229,0.177 10 false [C] 4.76,3.125 5.021,3.302 0.26,0.177 10 false [D] 5.781,3.135 6.052,3.333 0.271,0.198 10 false [D] 6.76,3.135 7.01,3.323 0.25,0.188 10 false [D] 6.938,2.177 7.146,2.354 0.208,0.177 10 false [E] 1.427,6.01 1.625,6.188 0.198,0.177 10 false [E] 3.417,4.781 3.76,4.958 0.344,0.177 10 false [H]* 5.948,4.427 6.448,4.604 0.5,0.177 10 false [J]* 4.375,6.969 4.573,7.146 0.198,0.177 10 false [I] 6.729,6.958 7,7.177 0.271,0.219 10 false [K] 1.708,6.958 1.906,7.135 0.198,0.177 10 false [F] 2.167,5.885 2.406,6.063 0.24,0.177 10 false [G] 2.052,6.521 2.823,6.708 0.771,0.188 10 false Warming up 0.854,6.01 1.281,6.198 0.427,0.188 10 false Idling 0.073,6.229 1.25,6.385 1.177,0.156 10 false Ignition Switch off 0.365,7.24 4.979,7.448 4.615,0.208 10 false *: Drive the vehicle while keeping the engine load as constant as possible.

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.

7.

Check that Catalyst Efficiency / Current is Incomplete.

8.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

9.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Drive the vehicle while keeping the engine load as constant as possible.


10.

With the shift lever in S, drive the vehicle at 60 km/h (37 mph), and then decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Enter the following menus: Powertrain / Engine / Monitor / Current Monitor / O2 Sensor / RL F/C B1S2 [D].

12.

Check the Test Value for RL F/C B1S2.

HINT:
·

If Test Value displays a value larger than 0, perform the following procedure, as the O2 sensor monitor is finished.

·

If Test Value displays 0, perform step [C] until it displays a value larger than 0, as the O2 sensor monitor is not finished.



13.

Turn the ignition switch off and wait for at least 30 seconds [F].

14.

Turn the ignition switch to ON and turn the GTS on.

15.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [G].

16.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [H].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Drive the vehicle while keeping the engine load as constant as possible.

·

The monitor item will change to Complete as the Catalyst Efficiency monitor operates [I].



17.

Enter the following menus: Powertrain / Engine / Trouble Codes.

18.

Check if any DTCs are stored.

HINT:

If the monitor item does not change to Complete, and no DTCs are stored, perform the following procedure.


19.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [J].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

Drive the vehicle while keeping the engine load as constant as possible.

·

The monitor item will change to Complete as the Catalyst Efficiency monitor operates [K].



20.

Enter the following menus: Powertrain / Engine / Trouble Codes.

21.

Check if any DTCs are stored.

HINT:

If the monitor item does not change to Complete, and no DTCs are stored, drive the vehicle again under an increased load.



CONDITIONING FOR SENSOR TESTING

HINT:

Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is to activate the sensors sufficiently to obtain appropriate inspection results.


A364135E13
4.865,3.104 4.865,3.313 4.865,3.313 5.281,3.313 false 5.188,3.313 5.188,3.135 false 0.583,0.594 1.552,0.781 0.969,0.188 10 false Engine Speed 0.844,1.01 1.49,1.208 0.646,0.198 10 false 3000 rpm 0.833,1.552 1.479,1.75 0.646,0.198 10 false 2000 rpm 1.094,2.531 1.49,2.74 0.396,0.208 10 false Idling 0.229,2.76 1.521,2.969 1.292,0.208 10 false Ignition Switch OFF 2.063,2.396 2.302,2.604 0.24,0.208 10 false [B] 6.615,2.74 7.031,2.938 0.417,0.198 10 false Time 2.073,3.135 2.896,3.344 0.823,0.208 10 false Warming up 3.375,3.146 4.583,3.354 1.208,0.208 10 false At least 3 minutes 5.344,3.208 6.073,3.396 0.729,0.188 10 false 2 seconds 4.885,3.354 5.354,3.552 0.469,0.198 10 false Check 1.604,2.646 1.844,2.854 0.24,0.208 10 false [A] 3.594,0.896 3.865,1.083 0.271,0.188 10 false [C] 4.75,0.885 4.99,1.073 0.24,0.188 10 false [D] 5.052,1.438 5.292,1.625 0.24,0.188 10 false [D]

(a) Connect the GTS to the DLC3 [A].

(b) Start the engine and warm it up with all the accessories switched off until the engine coolant temperature becomes stable [B].

(c) Run the engine at 2500 to 3000 rpm for at least 3 minutes [C].

(d)While running the engine at 3000 rpm for 2 seconds and 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the GTS [D].

HINT:
·

If the voltage output of either the air fuel ratio or heated oxygen sensor does not fluctuate, or there is a noise in the waveform of either sensor, the sensor may be malfunctioning.

·

If the voltage outputs of both the sensors remain lean or rich, the air-fuel ratio may be extremely lean or rich. In such cases, perform the Control the Injection Volume Active Test using the GTS.

·

If the Three-way Catalytic Converter (TWC) has deteriorated, the heated oxygen sensor (located behind the Three-way Catalytic Converter (TWC)) voltage output fluctuates up and down frequently, even under normal driving conditions (active air-fuel ratio control is not performed).


A195037E20
0.083,0.031 4.521,0.302 4.438,0.271 10 false Voltage output when active air fuel ratio control not performed: 2.5,0.448 3.521,0.677 1.021,0.229 10 false Normal Catalyst 4.802,0.438 6.167,0.667 1.365,0.229 10 false Deteriorated Catalyst 0.052,1.698 1.313,2.479 1.26,0.781 10 false Waveform of Heated Oxygen Sensor behind TWC 0.094,0.521 1.375,1.083 1.281,0.563 10 false Waveform of Air Fuel Ratio Sensor in front of TWC 1.469,0.76 1.865,0.99 0.396,0.229 10 false 3.5 V 1.469,1.115 1.865,1.323 0.396,0.208 10 false 3.0 V 1.479,2.073 1.865,2.281 0.385,0.208 10 false 1.0 V 1.573,2.74 1.865,2.969 0.292,0.229 10 false 0 V 2.635,3.104 3.375,3.292 0.74,0.188 10 false 10 seconds 5.125,3.104 5.854,3.292 0.729,0.188 10 false 10 seconds


CAUTION / NOTICE / HINT

HINT:
·

If a malfunction cannot be found when troubleshooting DTC P0420, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 (System Too Lean) and P0172 (System Too Rich).

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read DTCs.

Result
Result Proceed to
DTC P0420 is output A
DTC P0420 and other DTCs are output B

HINT:

If any DTCs other than P0420 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Perform the Active Test operation with the engine idling (press the 12.5 or -12.5 button to change the fuel injection volume).


g.

Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

Change the fuel injection volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen sensor)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V


Result
Status
AFS Voltage B1S1
Status
O2S B1S2
Actual Air Fuel Ratio,
Air fuel ratio sensor and heated oxygen sensor condition
Misfire Main Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal -
·

Three-way catalytic converter

·

Gas leak from exhaust system


A
Lean Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


B
Rich Lean/Rich Air fuel ratio sensor malfunction -
·

Air fuel ratio sensor


Lean/Rich Lean Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


C
Lean/Rich Rich Heated oxygen sensor malfunction -
·

Heated oxygen sensor

·

Gas leak from exhaust system


Lean Lean Actual air-fuel ratio lean May occur
·

Extremely rich or lean actual air-fuel ratio

·

Gas leak from exhaust system


D
Rich Rich Actual air-fuel ratio rich -
·

Extremely rich or lean actual air-fuel ratio

·

Gas leak from exhaust system




Lean: During Control the Injection Volume for A/F Sensor, the air-fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.



A

3.CHECK FOR EXHAUST GAS LEAK

B

5.REPLACE AIR FUEL RATIO SENSOR

C

6.CHECK FOR EXHAUST GAS LEAK

D

8.CHECK FOR EXHAUST GAS LEAK
3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST)

NG

10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST)
HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Replace the front exhaust pipe assembly (TWC: Front and rear catalyst) (See page Engine / Hybrid System>1NZ-FE INTAKE / EXHAUST>EXHAUST PIPE>REMOVAL).



NEXT

END

5.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>REMOVAL)

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
6.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

7.REPLACE HEATED OXYGEN SENSOR

NG

10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
7.REPLACE HEATED OXYGEN SENSOR
a.

Replace the heated oxygen sensor (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>REMOVAL).

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
8.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO

NG

10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR-FUEL RATIO
a.

Check the cause of extremely rich or lean actual air-fuel ratio, referring to the DTC P0171 Inspection Procedure (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0171).



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
10.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
a.

Repair or replace the exhaust gas leak point (See page Engine / Hybrid System>1NZ-FE INTAKE / EXHAUST>EXHAUST PIPE>COMPONENTS).

HINT:

Perform "Inspection After Repair" after replacing the exhaust system (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


k.

Read the DTCs.

Result
Result Proceed to
DTC P0420 is output A
DTC is not output
(No pending DTCs output)
B



A

12.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST)

B

END

12.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST)
HINT:

Confirm the replacement parts, referring to the illustration in the Catalyst Location.


a.

Replace the front exhaust pipe assembly (TWC: Front and rear catalyst) (See page Engine / Hybrid System>1NZ-FE INTAKE / EXHAUST>EXHAUST PIPE>REMOVAL).



NEXT

END