Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0171  System Too Lean (Bank 1)  P0172  System Too Rich (Bank 1)  


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection duration. The fuel trim consists of both the short-term and long-term fuel trims.

The short-term fuel trim is fuel compensation that is used to constantly maintain the air-fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air-fuel ratio is rich and an increase in the fuel injection volume if lean.

Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No. DTC Detection Condition Trouble Area
P0171 With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to lean side (2 trip detection logic)
·

Intake system

·

Fuel injector assembly blockage

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leakage in exhaust system

·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

No. 1 integration relay

·

PCV valve and hose

·

ECM

·

Wire harness


P0172 With warm engine and stable air-fuel ratio feedback, fuel trim considerably in error to rich side (2 trip detection logic)
·

Fuel injector assembly leak or blockage

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Ignition system

·

Fuel pressure

·

Gas leakage in exhaust system

·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

No. 1 integration relay

·

ECM

·

Wire harness



HINT:
·

When DTC P0171 is recorded, the actual air-fuel ratio is on the lean side. When DTC P0172 is recorded, the actual air-fuel ratio is on the rich side.

·

If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 may be recorded. The MIL is then illuminated.

·

If the total of the short-term fuel trim value and long-term fuel trim value is within the malfunction threshold (and engine coolant temperature is more than 75°C (167°F)), the system is functioning normally.



MONITOR DESCRIPTION

Under closed loop fuel control, fuel injection volumes that deviate from those estimated by the ECM cause changes in the long-term fuel trim compensation value. The long-term fuel trim is adjusted when there are persistent deviations in the short-term fuel trim values. Deviations from the fuel injection volumes estimated by the ECM also affect the average fuel trim learned value, which is a combination of the average short-term fuel trim (fuel feedback compensation value) and the average long-term fuel trim (learned value of the air-fuel ratio). If the average fuel trim learned value exceeds the malfunction thresholds, the ECM interprets this as a fault in the fuel system and stores a DTC.

Example:

The average fuel trim learned value is +48% or higher, or -35% or less, the ECM interprets this as a fuel system malfunction.

A381777E04
1.552,1.646 1.646,1.844 1.646,1.844 1.813,1.844 false 1.573,3.031 1.667,2.885 1.667,2.885 1.833,2.885 false 1.76,0.302 3.01,0.688 1.25,0.385 10 false Fuel Compensation Amount 1.917,1.74 2.271,1.948 0.354,0.208 10 false 1.48 1.927,2.281 2.281,2.49 0.354,0.208 10 false 1.0 1.938,2.802 2.292,3.01 0.354,0.208 10 false 0.65 0.292,1.281 1.51,1.802 1.219,0.521 10 false +48%: Malfunction Threshold of LEAN Condition 0.313,2.844 1.531,3.365 1.219,0.521 10 false -35%: Malfunction Threshold of RICH Condition

MONITOR STRATEGY

Required Sensors/Components Air fuel ratio sensor Mass air flow meter, Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Fuel system status Closed loop
Battery voltage 11 V or higher
Either of following conditions 1 or 2 met -
1. Engine RPM Less than 950 rpm
2. Engine load 16% or higher

TYPICAL MALFUNCTION THRESHOLDS

Purge-cut Executing
Either of following conditions 1 or 2 met -
1. Average of short-term fuel trim and long-term fuel trim +48% or more (varies with engine coolant temperature)
2. Average of short-term fuel trim and long-term fuel trim -35% or more (varies with engine coolant temperature)

CONFIRMATION DRIVING PATTERN

A199233E93
0.568,0.043 1.536,0.247 0.968,0.205 10 Vehicle Speed 1.247,1.962 1.653,2.139 0.406,0.177 10 Idling 0.442,2.249 1.709,2.405 1.268,0.156 10 Ignition Switch ON 2.009,2.339 2.210,2.540 0.201,0.201 10 [A] 2.529,1.836 2.734,2.013 0.205,0.177 10 [B] 3.324,1.839 3.548,2.011 0.224,0.171 10 [C] 4.797,0.442 5.026,0.615 0.229,0.173 10 [D] 5.622,3.29 5.846,3.461 0.224,0.171 10 [E] 0.414,0.317 1.625,0.480 1.211,0.163 10 120 km/h (74 mph) 0.44,1.198 1.652,1.361 1.211,0.163 10 60 km/h (37 mph) 4.343,2.922 5.541,3.099 1.198,0.177 10 5 minutes or more 2.13,2.992 2.925,3.169 0.795,0.177 10 Warming up 2.858,3.146 4.014,3.323 1.156,0.177 10 2 minutes or more 3.636,0.059 7.009,0.262 3.373,0.202 10 Engine coolant temperature is 75°C (167°F) or higher 3.062,2.043 3.463,0.148 3.463,0.148 3.585,0.148 false

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn GTS on [A].

6.

Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) with all the accessories switched off [B].

7.

With the engine warmed up, idle the engine for 2 minutes or more [C].

8.

Drive the vehicle at between 60 and 120 km/h (37 and 74 mph) and at an engine speed of between 1400 and 3200 rpm for 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0171 OR P0172)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read DTCs.

Result
Result Proceed to
DTC P0171 or P0172 is output A
DTC P0171 or P0172 and other DTCs are output B



A

2.CHECK CONNECTION OF PCV HOSE

B

2.CHECK CONNECTION OF PCV HOSE
a.

OK:

PCV hose is connected correctly and is not damaged.



OK

3.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV HOSE

3.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

OK:

No leaks in intake system.


HINT:
·

Perform "Inspection After Repair" after replacing the intake system (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).

·

If a malfunction occurs when depressing the brake pedal, inspect the brake booster assembly, as there may be a vacuum leak in the brake booster assembly itself.





OK

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

NG

REPAIR OR REPLACE INTAKE SYSTEM

4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.


f.

Perform the control the injection volume for A/F sensor operation with the engine idling (press the -12.5 or 12.5 button to change the fuel injection volume).


g.

Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

The control the injection volume for A/F sensor operation lowers or increases the fuel injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen sensor)
+12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Status AFS Voltage B1S1 Status O2S B1S2 Air-Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Suspected Trouble Area Proceed to
Lean/Rich Lean/Rich Normal - A
Lean Lean Actual air-fuel ratio lean
·

PCV valve and hose

·

PCV hose connections

·

Fuel injector assembly blockage

·

Gas leak from exhaust system

·

Intake system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


A
Rich Rich Actual air-fuel ratio rich
·

Fuel injector assembly leak or blockage

·

Gas leak from exhaust system

·

Ignition system

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor


Lean Lean/Rich Air fuel ratio sensor malfunction Air fuel ratio sensor B
Rich Lean/Rich Air fuel ratio sensor malfunction Air fuel ratio sensor


HINT:

Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.



A

5.READ VALUE USING GTS (COOLANT TEMP)

B

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
5.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.


d.

Read the Coolant Temp value when the engine is cold and warmed up.

Standard:
Tester Display Condition Specified Condition
Coolant Temp Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)



HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).



OK

6.READ VALUE USING GTS

NG

6.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF, Coolant Temp and Engine speed.


e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
MAF Shift lever position: N
A/C: OFF
Engine speed: 3000 rpm
Between 4.0 gm/sec. and 10 gm/sec.




OK

7.CHECK FUEL PRESSURE

NG

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
7.CHECK FUEL PRESSURE
a.

Check the fuel pressure (See page Engine / Hybrid System>1NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the fuel system (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




OK

8.CHECK EXHAUST GAS LEAK

NG

REPAIR OR REPLACE FUEL SYSTEM

8.CHECK EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.


OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after replacing the exhaust system (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).



OK

9.CHECK FOR SPARK AND IGNITION

NG

REPAIR OR REPLACE EXHAUST SYSTEM

9.CHECK FOR SPARK AND IGNITION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

If the spark plugs or ignition system malfunction, engine misfire may occur. The misfire counter can be read with the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count to #4.

·

Perform "Inspection After Repair" after replacing the ignition system (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




NEXT

10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Check the injection and volume.


HINT:
·

Refer to the fuel injector inspection procedure (See page Engine / Hybrid System>1NZ-FE FUEL>FUEL INJECTOR>INSPECTION).

·

If the injectors are malfunctioning, engine misfire may occur. The misfire counter can be read with the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count to #4.

·

Perform "Inspection After Repair" after replacing the fuel injector assembly (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




OK

15.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPLACE FUEL INJECTOR ASSEMBLY

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>INSPECTION).

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




OK

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

NG

12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
U126259C02
1.865,1.083 2.427,0.865 true 0.156,0.073 0.375,0.281 0.219,0.208 10 false *a 2.49,0.74 2.75,0.948 0.26,0.208 10 false +B 0.677,1.156 0.99,1.354 0.313,0.198 10 false B90
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


a.

Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B90-2 (+B) - Body ground Ignition switch ON 11 to 14 V




OK

13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

22.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY)
13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the B90 air fuel ratio sensor connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
B90-1 (HA1A) - B89-23 (HA1A) Always Below 1 Ω
B90-3 (A1A+) - B89-133 (A1A+) Always Below 1 Ω
B90-4 (A1A-) - B89-134 (A1A-) Always Below 1 Ω
B90-1 (HA1A) or B89-23 (HA1A) - Body ground Always 10 kΩ or higher
B90-3 (A1A+) or B89-133 (A1A+) - Body ground Always 10 kΩ or higher
B90-4 (A1A-) or B89-134 (A1A-) - Body ground Always 10 kΩ or higher




OK

14.REPLACE AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).

HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).




NEXT

15.PERFORM CONFIRMATION DRIVING PATTERN
15.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.



NEXT

16.CHECK WHETHER DTC OUTPUT RECURS
16.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0171 or P0172 is output A
DTC is not output B



A

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)

B

END

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


k.

Read the DTCs.

Result
Result Proceed to
DTC P0171 or P0172 is output A
DTC is not output B



A

19.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

B

END

19.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Disconnect the B72 mass air flow meter connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
B72-3 (VG) - B89-91 (VG) Always Below 1 Ω
B72-2 (E2G) - B89-92 (E2G) Always Below 1 Ω
B72-3 (VG) or B89-91 (VG) - Body ground Always 10 kΩ or higher
B72-2 (E2G) or B89-92 (E2G) - Body ground Always 10 kΩ or higher




OK

20.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.REPLACE MASS AIR FLOW METER
a.

Replace mass air flow meter (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>MASS AIR FLOW METER>REMOVAL).

HINT:
·

If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter (See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>INITIALIZATION).





NEXT

21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


k.

Read the DTCs.

Result
Result Proceed to
DTC is not output A
DTC P0171 or P0172 is output B



A

END

B

22.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the B90 air fuel ratio sensor connector.


b.

Remove the No. 1 integration relay from engine room relay block.


c.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
B90-2 (+B) - 1E-4 Always Below 1 Ω
B90-2 (+B) or 1E-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR