Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon emissions, fuel vapor from the fuel tank is routed through a canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV (Vacuum Switching Valve) so that the intake amount of hydrocarbon emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. DTC Detection Condition Trouble Area
P0443 Both of the following conditions (a) and (b) are met (1 trip detection logic)
(a) The target control value and actual control value do not match for 10 seconds or more.
(b) The target control value and actual control value do not match for 80 times or more.
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM



CONFIRMATION DRIVING PATTERN

A179391E06
1.525,1.949 1.755,2.124 0.230,0.174 10 [A] 2.846,1.949 3.076,2.124 0.230,0.174 10 [B] 3.892,3.005 4.122,3.179 0.230,0.174 10 [C] 4.574,1.338 4.804,1.512 0.230,0.174 10 [D] 5.097,3.005 5.327,3.179 0.230,0.174 10 [E] 0.509,2.071 0.887,2.255 0.378,0.184 10 Idling 4.224,2.524 5.010,2.837 0.786,0.313 10 10 minutes or more 2.594,2.524 3.380,2.837 0.786,0.313 10 15 minutes or more 1.31,2.524 2.105,2.689 0.795,0.165 10 Warming up 1.38,1.057 3.406,1.380 2.026,0.323 10 Between 40 km/h and 60 km/h (24 mph and 37 mph) 0.954,1.546 1.171,1.139 1.171,1.139 1.269,1.139 false 0.128,0.45 1.081,0.616 0.952,0.165 10 Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessory switches should be off.


9.

Idle the engine for 15 minutes or more [B].

HINT:

Check the EVAP (Purge) VSV item in the Data List. When the value of this item is between 5 and 95%, the judgment will be performed.


10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0443.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



15.

Drive the vehicle at a constant speed between 40 and 60 km/h (24 and 37 mph) for 10 minutes [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


16.

Check the DTC judgment result [E].


WIRING DIAGRAM

A254088E04
0.583,3.896 1.083,4.146 0.5,0.25 10 false Battery 0.406,3.073 0.771,3.24 0.365,0.167 10 false MAIN 0.406,2.5 0.604,2.646 0.198,0.146 10 false R/I 0.906,1.646 1.125,1.802 0.219,0.156 10 false 1E 0.917,1.458 1.115,1.625 0.198,0.167 10 false 10 0.896,1.125 1.125,1.271 0.229,0.146 10 false 1C 0.917,0.938 1.031,1.083 0.115,0.146 10 false 1 1.313,1.26 1.938,1.406 0.625,0.146 10 false EFI MAIN 2.115,1.927 2.813,2.177 0.698,0.25 10 false EFI MAIN 3.115,1.646 3.323,1.823 0.208,0.177 10 false 1D 3.156,1.438 3.26,1.604 0.104,0.167 10 false 7 3.104,1.125 3.302,1.271 0.198,0.146 10 false 1E 3.167,0.938 3.302,1.094 0.135,0.156 10 false 4 3.99,1.563 4.719,1.75 0.729,0.188 10 false Purge VSV 3.99,1.417 4.26,1.573 0.271,0.156 10 false B61 3.906,1.01 4.01,1.177 0.104,0.167 10 false 1 4.625,1.021 4.76,1.188 0.135,0.167 10 false 2 5.417,1.135 5.729,1.354 0.313,0.219 10 false B89 5.417,1.927 5.74,2.167 0.323,0.24 10 false A83 5.469,0.948 5.74,1.104 0.271,0.156 10 false 76 5.458,1.76 5.656,1.927 0.198,0.167 10 false 46 5.771,1.021 6.104,1.188 0.333,0.167 10 false PRG 5.771,1.938 6.208,2.104 0.438,0.167 10 false MREL 6.24,2.719 6.573,2.885 0.333,0.167 10 false ECM 1.396,2.302 2.917,2.5 1.521,0.198 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE PURGE VSV CONTROL)
a.
A257613C01
0.854,0.427 1.5,1.49 true 2.229,0.427 2.5,1.469 true 0.698,0.25 0.979,0.417 0.281,0.167 10 false *1 2.073,0.25 2.354,0.417 0.281,0.167 10 false *2
*1 Purge VSV
*2 Horse (to canister)


Connect the GTS to the DLC3.


b.

Disconnect the charcoal canister side vacuum hose from the purge VSV.


c.

Start the engine.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


f.

When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction to your finger.

OK:
GTS Operation Specified Condition
ON (Purge VSV is on) Purge VSV port applies suction to finger
OFF (Purge VSV is off) Purge VSV port applies no suction to finger




OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV

OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
a.
U158080C01
0.135,0.125 0.406,0.354 0.271,0.229 10 false *a 0.448,1.26 0.781,1.438 0.333,0.177 10 false B61
*a Front view of wire harness connector
(to Purge VSV)


Disconnect the purge VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B61-1 - Body ground Ignition switch ON 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (PURGE VSV - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the B61 purge VSV connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B61-2 - B89-76 (PRG) Always Below 1 Ω
B61-2 or B89-76 (PRG) - Body ground Always 10 kΩ or higher




OK

5.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Turn the GTS on.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


j.

Input the DTC: P0443.


k.

Check the DTC judgment result.


Result
Result Proceed to
DTC is not output A
DTC P0443 is output B

HINT:

If the judgment result shows INCOMPLETE or N/A, drive the vehicle at a constant speed between 40 and 60 km/h (24 and 37 mph) for 10 minutes and check the DTC judgment result again.



A

B

6.CHECK HARNESS AND CONNECTOR (PURGE VSV - NO. 1 INTEGRATION RELAY)
a.

Disconnect the B61 purge VSV connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
B61-1 - 1E-4 Always Below 1 Ω
B61-1 or 1E-4 - Body ground Always 10 kΩ or higher



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR