Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › from 2016.09
RM19S0E _58 Vehicle Interior _051498 HEATING / AIR CONDITIONING _0248353 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 87211A 1.INSTALL NO. 2 AIR DUCT

a.

Engage the 3 claws and install the air duct.


Hide 87211 2.INSTALL NO. 1 AIR DUCT

a.

Engage the 3 claws and install the air duct.


Hide 88669B 3.INSTALL COOLER AIR HOSE

a.

Install the cooler air hose.


Hide 87050 4.INSTALL AIR CONDITIONING RADIATOR ASSEMBLY

a.

Install the air conditioning radiator with the 3 screws.


Hide 88650N 5.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)

a.
I106866

Engage the claw and install the air conditioning amplifier as shown in the illustration.


b.

Tighten the screw.


Hide 88650N 6.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)

a.
I106867

Engage the claw and install the air conditioning amplifier as shown in the illustration.


b.

Tighten the screw.


Hide 82210K 7.INSTALL AIR CONDITIONING HARNESS ASSEMBLY (for LHD)

a.

Connect the connectors and engage the clamps, then install the air conditioning harness.


Hide 82210K 8.INSTALL AIR CONDITIONING HARNESS ASSEMBLY (for RHD)

a.

Connect the connectors and engage the clamps, then install the air conditioning harness.


Hide 9.TEMPORARILY TIGHTEN AIR CONDITIONER UNIT ASSEMBLY

a.

Temporarily tighten the air conditioning unit with the 3 bolts and nut.

NOTICE:

To prevent damage to the installation bracket for the air conditioning unit, be sure to support the air conditioning unit in place.



Hide 55331 10.INSTALL INSTRUMENT PANEL REINFORCEMENT

a.

Install the instrument panel reinforcement with the 8 bolts.

I106200


Hide 55306A 11.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the instrument panel brace with the 2 bolts, nut and screw.

HINT:

If the vehicle is equipped with knee airbag, install the knee airbag bracket mounting bolt.



Hide 12.INSTALL AIR CONDITIONER UNIT ASSEMBLY (for LHD)

a.

Install the air duct with the 2 bolts.

I106201E02
4.26,1.813 4.417,2.01 0.156,0.198 10 true 1 2.833,1.813 2.99,2.01 0.156,0.198 10 true 2 5.563,1.813 5.719,2.01 0.156,0.198 10 true 3 3.677,2.844 3.833,3.042 0.156,0.198 10 true 4 6.51,3.49 6.667,3.688 0.156,0.198 10 true 5 6.198,3.531 6.344,3.729 0.146,0.198 10 true 6

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.

Install the bolt, nut and 4 screws in the order shown in the illustration.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

for bolt


Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)

for nut


Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)

for screw 1, 2, 3



Hide 13.INSTALL AIR CONDITIONER UNIT ASSEMBLY (for RHD)

a.

Install the air duct with the 2 bolts.

I106831E02
4.115,1.885 4.25,2.052 0.135,0.167 10 true 1 2.927,1.885 3.063,2.052 0.135,0.167 10 true 2 1.854,1.885 1.99,2.052 0.135,0.167 10 true 3 3.969,2.833 4.104,3 0.135,0.167 10 true 4 1.24,3.479 1.375,3.646 0.135,0.167 10 true 6 0.813,3.479 0.948,3.646 0.135,0.167 10 true 5

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


b.

Install the bolt, nut and 4 screws in the order shown in the illustration.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

for bolt


Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)

for nut


Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)

for screw 1, 2, 3



Hide 82141 14.INSTALL INSTRUMENT PANEL WIRE (for LHD)

a.

Connect the connectors and engage the clamps, then install the instrument panel wire.


b.

Install the ground wire with the bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


c.

for Automatic Air Conditioning System:

i.

Engage the 2 clamps and connect the instrument panel wire.


ii.

Connect the 3 connectors.



d.

for Manual Air Conditioning System:

i.

Engage the 3 clamps and install the instrument panel wire.


ii.

Connect the 3 connectors.



e.

Connect the 3 clamps and install the connector holders.


f.

Tighten the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


g.

Connect the connectors.


h.

Install the wire harness protector with the screw.


i.

Engage the 2 clamps and install the connector holder.


j.

Tighten the screw.


k.

Connect the connectors.


l.
I106726

Connect the 2 clamps.


Hide 82141 15.INSTALL INSTRUMENT PANEL WIRE (for RHD)

a.

Connect the connectors and engage the clamps, then install the instrument panel wire.


b.

Install the ground wire with the bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


c.

for Automatic Air Conditioning System:

i.

Engage the 3 clamps and connect the instrument panel wire.


ii.

Connect the 2 connectors.



d.

for Manual Air Conditioning System:

i.

Engage the 5 clamps and install the instrument panel wire.


ii.

Connect the 3 connectors.



e.

Connect the 3 clamps and install the connector holders.


f.

Tighten the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


g.

Connect the connectors.


h.

Install the wire harness protector with the screw.


i.

Engage the 2 clamps and install the connector holder.


j.

Tighten the screw.


k.

Connect the connectors.


l.
I106727

Connect the 2 clamps.


Hide 82730 16.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

a.
I106071E02
2.26,0.677 2.396,0.865 0.135,0.188 10 true 2 2.688,1.625 2.823,1.813 0.135,0.188 10 false 1 2.635,0.219 2.771,0.406 0.135,0.188 10 false 3

Connect the back side connectors and install the instrument panel junction block as shown in the illustration.

NOTICE:

Securely connect the connector.



b.

Install the instrument panel junction block with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


c.
I105930

Connect the front side connectors as shown in the illustration.

NOTICE:

Securely connect the connector.



d.

Engage the clamps.


Hide 88539J 17.CONNECT DRAIN COOLER HOSE

a.
I107060E02
2.26,1.271 2.688,1.479 true 2.698,1.406 2.917,1.625 0.219,0.219 10 true *a 1.833,2.188 2.219,2.375 0.385,0.188 10 false 60°

Install the drain cooler hose as shown in the illustration.

Text in Illustration
*a UP Mark

NOTICE:
·

Install the drain hose with its UP mark facing upward, within the 60 degree range shown in the illustration.

·

Install the drain hose without twisting it.




Hide 55950G 18.INSTALL DEFROSTER NOZZLE ASSEMBLY

a.

Engage the 2 claws and 3 guides, then install the defroster nozzle.


b.

Engage the clamps and connect the connectors, then connect the wire harness.


Hide 55870B 19.INSTALL HEATER TO REGISTER DUCT ASSEMBLY

a.

Engage the 3 claws and install the heater to register duct.


Hide 4520A 20.INSTALL STEERING COLUMN ASSEMBLY (for LHD)

Hide 4520A 21.INSTALL STEERING COLUMN ASSEMBLY (for RHD)

Hide 55303B 22.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 87245A 23.CONNECT HEATER WATER INLET HOSE A

a.
I105941E02
1.708,3.198 1.333,2.865 false 1.021,1.615 1.188,1.792 0.167,0.177 10 true A 0.979,2.292 1.177,2.469 0.198,0.177 10 false *a 1.135,2.74 1.333,2.917 0.198,0.177 10 false *b 2.323,2.583 2.802,2.771 0.479,0.188 10 false 60°

Connect the heater water inlet hose onto the air conditioning unit.

Text in Illustration
*a View A
*b White Paint Mark

HINT:

Perform the installation with the hose clip and mark at the correct angle.



Hide 87246A 24.CONNECT HEATER WATER OUTLET HOSE A

a.
I105942E02
1.667,3.26 1.344,2.802 false 1.094,1.552 1.26,1.729 0.167,0.177 10 true A 0.885,2.292 1.094,2.469 0.208,0.177 10 false *a 1.146,2.667 1.354,2.844 0.208,0.177 10 false *b 2.531,2.844 2.927,3.01 0.396,0.167 10 false 90°

Connect the heater water outlet hose onto the air conditioning unit.

Text in Illustration
*a View A
*b Purple Paint Mark

HINT:

Perform the installation with the hose clip and mark at the correct angle.



Hide 88706A 25.CONNECT LIQUID TUBE SUB-ASSEMBLY A

a.

Remove the vinyl tape from liquid tube and the connecting portion of the unit.


b.

Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the liquid tube.

Compressor oil:

ND-OIL8 or equivalent



c.

Install the O-ring onto the liquid tube.


d.

Connect the liquid tube to the unit.


Hide 88707B 26.CONNECT SUCTION TUBE SUB-ASSEMBLY B

a.

Remove the vinyl tape from suction tube and the connecting portion of the unit.


b.

Apply sufficient compressor oil (ND-OIL8) to a new O-ring and the connecting part of the suction tube.

Compressor oil:

ND-OIL8 or equivalent



c.

Install the O-ring onto the suction tube.


d.

Securely connect the suction tube to the air conditioning unit.


e.
I105938

Turn the hook connector in the direction indicated by the arrow in the illustration.


f.

Insert the pipe joints securely into the fitting holes and tighten the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 55722C 28.INSTALL COWL TOP TO COWL INNER BRACE

Hide 55735D 29.INSTALL FRONT AIR SHUTTER SEAL RH

Hide 55815E 30.INSTALL FRONT NO. 1 VENTILATOR SEAL

Hide 31.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 32.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION