While the engine is being cranked, the positive battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0617 | Conditions (a), (b) and (c) are met, and a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):
(a) Vehicle speed is 20 km/h (12.4 mph) or more. (b) Engine speed is 1000 rpm or more. (c) STA signal is on. |
·
Park/neutral position switch*1 ·
Clutch start switch assembly*2 ·
Starter relay (ST) circuit ·
Ignition switch assembly ·
ECM |
*1: for Automatic Transaxle
*2: for Manual Transaxle
| Required Sensors/Components (Main) | Starter relay, Park/Neutral position switch, Clutch start switch assembly and Ignition switch |
| Required Sensors/Components (Related) | Vehicle speed sensor, Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Vehicle speed | 20 km/h (12.4 mph) or more |
| Engine speed | 1000 rpm or more |
| Starter signal | ON |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on [A].
Idle the engine for 5 seconds or more [B].
Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
Read pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0617.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.
Refer to DTC Starter Signal Circuit (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>Starter Signal Circuit).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.
If the engine does not crank, proceed to Problem Symptoms Table (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>PROBLEM SYMPTOMS TABLE).
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the GTS when the ignition switch is turned to ON and the engine is started.
| Ignition Switch Position | GTS Display |
|---|---|
| ON | OFF |
| START | ON |
| Result | Proceed to |
|---|---|
| OK | A |
| NG
(for automatic transaxle) |
B |
| NG
(for manual transaxle) |
C |
A
B
C
Disconnect the B88 park/neutral position switch connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the GTS when the ignition switch is turned to ON.
| Result | Proceed to |
|---|---|
| Remains ON | A |
| OFF | B |
A
B
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the B88 park/neutral position switch connector.
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
|---|---|---|---|
| A83-22 (STA) - Body ground | Ignition switch ON | 11 to 14 V | A |
| Below 1.5 V | B |
A
B
| *a | Component without harness connected
(Park/Neutral Position Switch) |
Disconnect the park/neutral position switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (B) - 5 (L) | Shift lever in any position other than P or N | 10 kΩ or higher |
| 2 (RB) - 5 (L) | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| Short between 4 (B) and 5 (L) | A |
| Short between 2 (RB) and 5 (L) | B |
| Within standard range | C |
A
B
(See pageDrivetrain>U441E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL)
C
Replace the park/neutral position switch (See page Drivetrain>U441E (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>REMOVAL).
NEXT
Disconnect the A39 clutch start switch assembly connector.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
Read the value displayed on the GTS when the ignition switch is turned to ON.
| Result | Proceed to |
|---|---|
| ON | A |
| OFF | B |
A
B
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the A39 clutch start switch assembly connector.
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
|---|---|---|---|
| A83-22 (STA) - Body ground | Ignition switch ON | 11 to 14 V | A |
| Below 1.5 V | B |
A
B
Inspect the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION).
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Replace the clutch start switch assembly (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL).
NEXT
Inspect the ignition switch assembly (See page Engine / Hybrid System>2NZ-FE STARTING>IGNITION SWITCH>INSPECTION).
OK
NG
| *a | Front view of wire harness connector
(to ECM) |
Disconnect the park/neutral position switch*1 or clutch start switch*2 connector.
*1: for Automatic Transaxle
*2: for Manual Transaxle
Disconnect the ECM connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition | Proceed to |
|---|---|---|---|
| B89-63 (NSW) - Body ground | Ignition switch ON | 11 to 14 V | A
(for automatic transaxle) |
| B
(for manual transaxle) |
|||
| Below 1.5 V | C |
A
B
C