The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU, which uses this information to create the vehicle speed sensor signal*1. The vehicle speed sensor signal consists of pulses sent to the combination meter assembly from the skid control ECU. To create this signal, 12 V is output from IG2, which is behind a resistor in the combination meter assembly. This voltage is sent to the skid control ECU. The pulse signal is created by switching the transistor in the skid control ECU on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on the pulse signal.
*1: This vehicle speed sensor signal is created by the skid control ECU. There is no actual component that is referred to as the vehicle speed sensor. In addition, for some other systems, vehicle speed information may be exchanged using CAN communication.
This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.
Disconnect the combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F1-6 (+S) - Body ground | Ignition switch ON | 4.5 to 14 V |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.
Reconnect the combination meter assembly connector.
OK
NG
Disconnect the brake actuator assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A54-11 (SP1) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Brake Actuator Assembly) |
Reconnect the brake actuator assembly connector.
OK
NG
Check the input waveform.
Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal F1-5 (SI) and body ground.
Turn the ignition switch to ON.
Turn the wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Driving at approximately 20 km/h (12 mph) |
The waveform is displayed as shown in the illustration.
As the vehicle speed increases, the cycle of the waveform narrows.
| *a | Component with harness connected
(Combination Meter Assembly) |
OK
NG
Disconnect the F1 combination meter assembly connector.
Disconnect the A54 brake actuator assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A54-11 (SP1) - F1-5 (SI) | Always | Below 1 Ω |
| A54-11 (SP1) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the 3B instrument panel junction block assembly connector.
Disconnect the F1 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-6 (+S) - 3B-15 | Always | Below 1 Ω |
| F1-6 (+S) - Body ground | Always | 10 kΩ or higher |
Reconnect the instrument panel junction block assembly connector.
Reconnect the combination meter assembly connector.
OK
NG
For vehicle without headlight leveling, go to step 7.
Disconnect the instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3C-40 - Body ground | Ignition switch ON | 4.5 to 14 V |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
OK
NG
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for Radio and Display Receiver Type | A |
| for Navigation Receiver Type | B |
| w/o Audio | C |
A
B
C
Disconnect the instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3A-16 - Body ground | Ignition switch ON | 4.5 to 14 V |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
OK
NG
Disconnect the instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3C-39 - Body ground | Ignition switch ON | 4.5 to 14 V |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
OK
NG
Disconnect the instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3A-16 - Body ground | Ignition switch ON | 4.5 to 14 V |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
OK
NG
Disconnect the instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3C-39 - Body ground | Ignition switch ON | 4.5 to 14 V |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
Reconnect the instrument panel junction block assembly connector.
OK
NG
Disconnect the 3C instrument panel junction block assembly connector.
Disconnect the A82 headlight leveling ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-40 - A82-16 (SPDR) | Always | Below 1 Ω |
| 3C-40 - Body ground | Always | 10 kΩ or higher |
Reconnect the instrument panel junction block assembly connector.
Reconnect the headlight leveling ECU assembly connector.
OK
NG
Disconnect the 3A instrument panel junction block assembly connector.
Disconnect the F132 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-16 - F132-17 (SPD) | Always | Below 1 Ω |
| 3A-16 - Body ground | Always | 10 kΩ or higher |
Reconnect the instrument panel junction block assembly connector.
Reconnect the radio and display receiver assembly connector.
OK
NG
Disconnect the 3A instrument panel junction block assembly connector.
Disconnect the F127 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-16 - F127-17 (SPD) | Always | Below 1 Ω |
| 3A-16 - Body ground | Always | 10 kΩ or higher |
Reconnect the instrument panel junction block assembly connector.
Reconnect the navigation receiver assembly connector.
OK
NG
Disconnect the 3C instrument panel junction block assembly connector.
Disconnect the A83 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3C-39 - A83-44 (SPD) | Always | Below 1 Ω |
| 3C-39 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| NG | A |
| OK (for 1NZ-FE) | B |
| OK (for 2NZ-FE) | C |
Reconnect the instrument panel junction block assembly connector.
Reconnect the ECM connector.
A
B
C