Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense) › from 2017.01
RM19S0E _57 Power Source / Network _051489 NETWORKING _0307624 CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)  Open in One Side of CAN Branch Line  


DESCRIPTION

If 2 or more ECUs and/or sensors do not appear on the intelligent tester "Bus Check" screen, one side of the CAN branch wire may be open (one side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).

Symptom Trouble Area
2 or more ECUs and/or sensors do not appear on the intelligent tester "CAN Bus Check" screen.
·

Open in side of CAN branch wire

·

Airbag sensor assembly

·

Skid control ECU (brake actuator assembly)

·

Main body ECU (multiplex network body ECU)

·

Power steering ECU assembly

·

Steering angle sensor (spiral cable sub-assembly)

·

Air conditioning amplifier assembly

·

Radio and display receiver assembly*1

·

Navigation receiver assembly*2

·

No. 1 junction connector

·

No. 2 junction connector



*1: for Radio and Display Type

*2: for Navigation Receiver Type


WIRING DIAGRAM

E295566E03
0.948,5.344 2.698,5.667 1.75,0.323 10 false : CAN Branch Wire (CAN-L) 0.948,5.042 2.719,5.365 1.771,0.323 10 false : CAN Branch Wire (CAN-H) 0.948,4.76 2.615,5.083 1.667,0.323 10 false : CAN Main Wire (CAN-L) 0.948,4.438 2.615,4.76 1.667,0.323 10 false : CAN Main Wire (CAN-H) 5.427,3.781 5.865,3.948 0.438,0.167 10 false F76 5.427,3.938 7.094,4.469 1.667,0.531 10 false Main Body ECU (Multiplex Network Body ECU) 0.115,3.802 1.677,4.323 1.563,0.521 10 false Skid Control ECU (Brake Actuator Assembly) 1.792,3.073 2.063,3.24 0.271,0.167 10 false 14 1.802,2.521 2.073,2.688 0.271,0.167 10 false 25 2.76,3 3.031,3.167 0.271,0.167 10 false 21 2.719,3.177 2.99,3.344 0.271,0.167 10 false A61 2.76,2.448 3.031,2.615 0.271,0.167 10 false 10 1.323,3.188 1.719,3.354 0.396,0.167 10 false CANL 3.854,0.885 4.25,1.052 0.396,0.167 10 false CANL 1.323,2.615 1.74,2.781 0.417,0.167 10 false CANH 3.042,0.885 3.458,1.052 0.417,0.167 10 false CANH 2.719,2.625 2.99,2.792 0.271,0.167 10 false A61 3.792,1.375 3.979,1.542 0.188,0.167 10 false 26 3.021,1.375 3.198,1.542 0.177,0.167 10 false 13 3.677,2.063 3.865,2.229 0.188,0.167 10 false 20 3.906,2.052 4.177,2.219 0.271,0.167 10 false A61 2.948,2.063 3.052,2.229 0.104,0.167 10 false 9 3.115,2.052 3.385,2.219 0.271,0.167 10 false A61 3.688,4.208 3.875,4.375 0.188,0.167 10 false 15 3.906,4.208 4.177,4.375 0.271,0.167 10 false F82 2.969,4.208 3.073,4.375 0.104,0.167 10 false 4 3.125,4.208 3.396,4.375 0.271,0.167 10 false F82 4.5,0.573 5.073,0.74 0.573,0.167 10 false A83 4.5,0.74 5.073,0.906 0.573,0.167 10 false ECM 4.333,3.177 4.604,3.344 0.271,0.167 10 false 12 4.292,3.354 4.563,3.521 0.271,0.167 10 false F82 4.365,2.625 4.635,2.792 0.271,0.167 10 false 1 5.5,3.344 5.938,3.51 0.438,0.167 10 false CANL 5.5,2.802 5.938,2.969 0.438,0.167 10 false CANH 4.292,2.802 4.563,2.969 0.271,0.167 10 false F82 5.26,3.25 5.531,3.417 0.271,0.167 10 false 13 5.26,2.698 5.531,2.865 0.271,0.167 10 false 14 4.333,2.177 5.958,2.5 1.625,0.323 10 false No. 1 Junction Connector 0.115,3.635 0.385,3.802 0.271,0.167 10 false A54

E295567E04
0.083,7.76 2.635,8.042 2.552,0.281 10 false *2: for Manual Air Conditioning System 0.083,7.427 2.729,7.75 2.646,0.323 10 false *1: for Automatic Air Conditioning System 6.104,4.49 6.375,4.656 0.271,0.167 10 false F4 6.104,4.656 6.531,4.979 0.427,0.323 10 false DLC3 1.26,0.75 1.531,0.917 0.271,0.167 10 false F83 1.26,0.938 2.885,1.26 1.625,0.323 10 false No. 2 Junction Connector 0.052,2.167 0.323,2.333 0.271,0.167 10 false F6 0.052,6.781 2.281,7.104 2.229,0.323 10 false Air Conditioning Amplifier Assembly 0.052,2.333 2.031,2.656 1.979,0.323 10 false Power Steering ECU Assembly 5.635,1.208 6.865,1.646 1.229,0.438 10 false Navigation Receiver Assembly*4 5.49,6.281 5.76,6.448 0.271,0.167 10 false F16 5.49,6.479 7.073,6.802 1.583,0.323 10 false Airbag Sensor Assembly 5.365,8.063 7.115,8.385 1.75,0.323 10 false : CAN Branch Wire (CAN-L) 5.365,7.719 7.135,8.042 1.771,0.323 10 false : CAN Branch Wire (CAN-H) 5.365,7.396 7.031,7.719 1.667,0.323 10 false : CAN Main Wire (CAN-L) 5.365,7.052 7.031,7.375 1.667,0.323 10 false : CAN Main Wire (CAN-H) 2.615,8.344 2.885,8.51 0.271,0.167 10 false F1 2.615,8.51 4.479,8.833 1.865,0.323 10 false Combination Meter Assembly 0.063,4.229 0.5,4.396 0.438,0.167 10 false F30 0.063,4.417 1.917,4.927 1.854,0.51 10 false Steering Angle Sensor (Spiral Cable Sub-assembly) 2.135,6.052 2.406,6.219 0.271,0.167 10 false 9 2.052,6.229 2.323,6.396 0.271,0.167 10 false F41 2.094,6.427 2.365,6.594 0.271,0.167 10 false *2 2.094,5.865 2.365,6.031 0.271,0.167 10 false *2 2.146,5.521 2.417,5.688 0.271,0.167 10 false 8 2.052,5.688 2.323,5.854 0.271,0.167 10 false F41 1.771,6.052 2.042,6.219 0.271,0.167 10 false 12 1.729,6.229 2,6.396 0.271,0.167 10 false F42 1.771,6.427 2.042,6.594 0.271,0.167 10 false *1 1.771,5.865 2.042,6.031 0.271,0.167 10 false *1 1.781,5.521 2.052,5.688 0.271,0.167 10 false 11 1.729,5.688 2,5.854 0.271,0.167 10 false F42 1.25,6.229 1.688,6.417 0.438,0.188 10 false CANL 1.24,5.688 1.698,5.865 0.458,0.177 10 false CANH 1.271,1.771 1.667,1.938 0.396,0.167 10 false CANL 1.26,1.396 1.688,1.563 0.427,0.167 10 false CANH 2.76,1.667 3.031,1.833 0.271,0.167 10 false 17 2.823,1.323 3.094,1.49 0.271,0.167 10 false 6 1.729,1.667 2,1.833 0.271,0.167 10 false 8 1.729,1.313 2,1.479 0.271,0.167 10 false 7 1.26,3.906 1.656,4.073 0.396,0.167 10 false CANL 1.26,3.563 1.688,3.729 0.427,0.167 10 false CANH 2.729,6.135 3,6.302 0.271,0.167 10 false 19 2.771,5.594 3.042,5.76 0.271,0.167 10 false 8 2.771,3.813 3.042,3.979 0.271,0.167 10 false 12 2.833,3.458 3.104,3.625 0.271,0.167 10 false 1 1.75,3.823 2.021,3.99 0.271,0.167 10 false 3 1.75,3.469 2.021,3.635 0.271,0.167 10 false 4 5.521,5.896 5.917,6.063 0.396,0.167 10 false CANL 5.521,5.521 5.948,5.688 0.427,0.167 10 false CANH 3.729,7.875 4.125,8.042 0.396,0.167 10 false CANL 3.063,7.885 3.49,8.052 0.427,0.167 10 false CANH 4.219,5.802 4.49,5.969 0.271,0.167 10 false 15 4.229,5.438 4.5,5.604 0.271,0.167 10 false 4 5.26,5.802 5.531,5.969 0.271,0.167 10 false 22 5.26,5.438 5.531,5.604 0.271,0.167 10 false 13 5.5,4.167 5.896,4.333 0.396,0.167 10 false CANL 5.5,3.802 5.927,3.969 0.427,0.167 10 false CANH 4.24,4.083 4.51,4.25 0.271,0.167 10 false 22 4.24,3.719 4.51,3.885 0.271,0.167 10 false 11 5.25,4.083 5.521,4.25 0.271,0.167 10 false 14 5.333,3.719 5.604,3.885 0.271,0.167 10 false 6 3.75,7.354 4.021,7.521 0.271,0.167 10 false 31 2.99,7.354 3.26,7.521 0.271,0.167 10 false 32 3.75,6.938 4.021,7.104 0.271,0.167 10 false 18 3.031,6.938 3.302,7.104 0.271,0.167 10 false 7 3.771,0.552 4.042,0.719 0.271,0.167 10 false 21 2.979,0.552 3.25,0.719 0.271,0.167 10 false 10 0.083,8.083 2.135,8.313 2.052,0.229 10 false *3: for Radio and Display Type 0.083,8.417 2.135,8.646 2.052,0.229 10 false *4: for Navigation Receiver Type 5.5,0.656 5.896,0.823 0.396,0.167 10 false CANL 5.5,0.281 5.927,0.448 0.427,0.167 10 false CANH 5.281,0.552 5.552,0.719 0.271,0.167 10 false 10 5.344,0.188 5.615,0.354 0.271,0.167 10 false 9 5.5,2.458 5.896,2.625 0.396,0.167 10 false CANL 5.5,2.083 5.927,2.25 0.427,0.167 10 false CANH 5.281,2.365 5.552,2.531 0.271,0.167 10 false 10 5.344,1.99 5.615,2.156 0.271,0.167 10 false 9 5.333,2.854 5.823,3.021 0.49,0.167 10 false F127 5.635,1.042 6.125,1.208 0.49,0.167 10 false F132 5.333,3.021 7.135,3.406 1.802,0.385 10 false Radio and Display Receiver Assembly*3 4.25,2.354 4.521,2.521 0.271,0.167 10 false 16 4.271,1.979 4.542,2.146 0.271,0.167 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Turn the ignition switch off before measuring the resistances of the CAN main wire and the CAN branch wire.

·

After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not in operation.

·

Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Perform the following inspection for the ECUs (sensors) which are not displayed on the intelligent tester. If a malfunction cannot be identified, perform the following inspections for the ECUs (sensors) connected to the CAN communication system.

·

Do not remove the combination meter assembly and ECM, as they are the end parts of the circuit. If removed, CAN communication will not be possible.

·

The open circuit confirmation of the combination meter assembly, ECM and main wire is performed in the "Check CAN Bus Line" procedure of "How to Proceed with Troubleshooting". This inspection only has procedures for checking for an open circuit on one side of the CAN branch wire.



PROCEDURE

1.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Disconnect the A54 skid control ECU (brake actuator assembly) connector.


b.

Select "Communication Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Skid Control (ABS/VSC/TRAC)" not displayed on intelligent tester. A
Several ECUs and sensors other than "Skid Control (ABS/VSC/TRAC)" not displayed on intelligent tester. B



A

2.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE)

B

3.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
2.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE)
E351556C01
1.469,0.323 1.969,0.573 0.5,0.25 1.25,1.781 1.708,0.771 true 1.729,2.708 1.25,1.958 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.583,0.354 2.042,0.552 0.458,0.198 10 false A54 1.781,0.677 2.396,0.875 0.615,0.198 10 false CANL 1.813,2.625 2.427,2.823 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A54-25 (CANH) - A54-14 (CANL) Ignition switch off 54 to 69 Ω



b.

Reconnect the skid control ECU (brake actuator assembly) connector.



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) BRANCH WIRE)

3.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F42*1 or F41*2 air conditioning amplifier assembly connector.

*1 : for Automatic Air Conditioning System

*2 : for Manual Air Conditioning System


b.

Select "Communication Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Air Conditioning Amplifier" not displayed on intelligent tester. A
Several ECUs and sensors other than "Air Conditioning Amplifier" not displayed on intelligent tester. B



A

4.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)

B

5.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY)
4.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)
U127247C04
1.74,0.854 1.375,0.354 true 1.917,0.854 2.229,0.365 true 2.542,2.24 2.375,1.729 true 2.708,2.24 2.885,1.729 true 1.552,0.104 1.844,0.26 0.292,0.156 10 false F42 0.104,0.104 0.396,0.26 0.292,0.156 10 false *a 0.104,1.583 0.396,1.74 0.292,0.156 10 false *b 1.552,1.542 1.844,1.698 0.292,0.156 10 false F41 0.948,0.229 1.396,0.417 0.448,0.188 10 false CANH 2.271,0.219 2.74,0.417 0.469,0.198 10 false CANL 1.948,1.604 2.417,1.781 0.469,0.177 10 false CANH 2.927,1.573 3.375,1.781 0.448,0.208 10 false CANL
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly (for Automatic Air Conditioning System))
*b Front view of wire harness connector
(to Air Conditioning Amplifier Assembly (for Manual Air Conditioning System (w/ Cooler)))


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F42-11 (CANH) - F42-12 (CANL)*1
F41-8 (CANH) - F41-9 (CANL)*2
Ignition switch off 54 to 69 Ω


*1 : for Automatic Air Conditioning System

*2 : for Manual Air Conditioning System


b.

Reconnect the air conditioning amplifier assembly connector.



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH WIRE)

5.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the F16 airbag sensor assembly connector.


b.

Select "Communication Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Airbag" not displayed on intelligent tester. A
Several ECUs and sensors other than "Airbag" not displayed on intelligent tester. B



A

6.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)

B

7.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY))
6.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)
a.
U127165C03
1.073,2.208 0.76,2.698 true 1.823,2.781 1.333,1.802 true 1.604,0.635 1.896,0.792 0.292,0.156 10 false F16 0.063,0.052 0.354,0.208 0.292,0.156 10 false *a 1.896,2.677 2.313,2.833 0.417,0.156 10 false CANH 0.323,2.594 0.74,2.75 0.417,0.156 10 false CANL
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F16-13 (CANH) - F16-22 (CANL) Ignition switch off 54 to 69 Ω



b.

Reconnect the airbag sensor assembly connector.



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (AIRBAG SENSOR ASSEMBLY BRANCH WIRE)

7.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY))
a.

Disconnect the F30 steering angle sensor (spiral cable sub-assembly) connector.


b.

Select "Communication Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Spiral cable (Steering Angle Sensor)" not displayed on intelligent tester. A
Several ECUs and sensors other than "Spiral cable (Steering Angle Sensor)" not displayed on intelligent tester. B



A

8.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)

B

9.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
8.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)
a.
U127163C03
1.969,2.24 2.292,2.729 true 1.5,2.24 1.177,2.729 true 1.552,0.469 1.844,0.625 0.292,0.156 10 false F30 0.177,0.094 0.469,0.25 0.292,0.156 10 false *a 2.094,2.74 2.51,2.896 0.417,0.156 10 false CANH 0.979,2.74 1.396,2.896 0.417,0.156 10 false CANL
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F30-4 (CANH) - F30-3 (CANL) Ignition switch off 54 to 69 Ω



b.

Reconnect the steering angle sensor (spiral cable sub-assembly) connector.



OK

REPLACE STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR (SPIRAL CABLE SUB-ASSEMBLY) BRANCH WIRE)

9.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the F76 main body ECU (multiplex network body ECU) connector.


b.

Select "Communication Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Main Body" not displayed on intelligent tester. A
Several ECUs and sensors other than "Main Body" not displayed on intelligent tester. B



A

10.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)

B

11.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)
10.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)
a.
U127253C03
1.344,1.875 1.833,1.146 true 2.469,1.885 1.979,1.156 true 1.583,0.219 1.875,0.375 0.292,0.156 10 false F76 0.083,0.052 0.375,0.208 0.292,0.156 10 false *a 2.521,1.823 2.938,1.979 0.417,0.156 10 false CANH 0.896,1.813 1.313,1.969 0.417,0.156 10 false CANL
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F76-14 (CANH) - F76-13 (CANL) Ignition switch off 54 to 69 Ω



b.

Reconnect the main body ECU (multiplex network body ECU) connector.



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) BRANCH WIRE)

11.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY)
HINT:

For vehicles except radio and display type, go to step 13.


a.

Disconnect the F127 radio and display receiver assembly connector.


b.

Select "Communication Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Display and Navigation (AVN1)" not displayed on intelligent tester. A
Several ECUs and sensors other than "Display and Navigation (AVN1)" not displayed on intelligent tester. B



A

12.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)

B

13.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (NAVIGATION RECEIVER ASSEMBLY)
12.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)
U158741C01
1.906,1.354 1.563,0.438 true 2.063,1.354 2.406,0.448 true 0.135,1.198 0.583,1.458 0.448,0.26 10 false F127 1.135,0.302 1.583,0.563 0.448,0.26 10 false CANH 0.135,0.094 0.583,0.354 0.448,0.26 10 false *a 2.448,0.313 2.979,0.573 0.531,0.26 10 false CANL
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F127-9 (CANH) - F127-10 (CANL) Ignition switch off 54 to 69 Ω



b.

Reconnect the radio and display receiver assembly connector.



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH WIRE)

13.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (NAVIGATION RECEIVER ASSEMBLY)
HINT:

For vehicles except navigation receiver type, go to step 15.


a.

Disconnect the F132 navigation receiver assembly connector.


b.

Select "Communication Bus Check" on the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/o Toyota Safety Sense)>DIAGNOSIS SYSTEM).

Result
Result Proceed to
"Display and Navigation (AVN1)" not displayed on intelligent tester. A
Several ECUs and sensors other than "Display and Navigation (AVN1)" not displayed on intelligent tester. B



A

14.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)

B

15.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY BRANCH WIRE)
14.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)
U158742C01
1.917,1.344 1.573,0.427 true 2.083,1.365 2.427,0.458 true 0.146,1.198 0.594,1.458 0.448,0.26 10 false F132 1.146,0.323 1.594,0.583 0.448,0.26 10 false CANH 0.135,0.083 0.583,0.344 0.448,0.26 10 false *a 2.479,0.313 3.01,0.573 0.531,0.26 10 false CANL
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F132-9 (CANH) - F132-10 (CANL) Ignition switch off 54 to 69 Ω



b.

Reconnect the navigation receiver assembly connector.



OK

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY BRANCH WIRE)

15.CHECK OPEN IN ONE SIDE OF CAN BRANCH WIRE (POWER STEERING ECU ASSEMBLY BRANCH WIRE)
a.

Disconnect the power steering ECU assembly connector.


b.
U127246C04
1.677,1.083 2,1.573 true 1.521,1.094 1.198,1.583 true 1.615,0.063 1.906,0.219 0.292,0.156 10 false F6 0.104,0.063 0.396,0.219 0.292,0.156 10 false *a 2.042,1.542 2.458,1.698 0.417,0.156 10 false CANH 0.792,1.531 1.208,1.688 0.417,0.156 10 false CANL
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
F6-7 (CANH) - F6-8 (CANL) Ignition switch off 54 to 69 Ω



c.

Reconnect the power steering ECU assembly connector.



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY BRANCH WIRE)