The pre-crash safety city sensor receives vehicle speed signals from the brake actuator assembly (skid control ECU). When the brake actuator assembly (skid control ECU) detects a malfunction in the vehicle wheel speed sensor, the pre-crash safety city sensor is notified via CAN communication and DTC C1AA3 is output.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1AA3 | Both of the following conditions are met:
1.
All of the following conditions are met: -
3 seconds have elapsed since the ignition switch to ON. -
The battery voltage is 10 V or more for 3 seconds or more. 2.
All of the following conditions are met for 1 second or more: -
Communication between the pre-crash safety city sensor and brake actuator assembly (skid control ECU) is normal. -
The pre-crash safety city sensor receives a wheel speed sensor malfunction signal from the brake actuator assembly (skid control ECU). |
·
Vehicle stability control system ·
Brake actuator assembly (skid control ECU) ·
Pre-crash safety city sensor |
When replacing the pre-crash safety city sensor, replace it with a new one. If an ECU which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be output.
If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust
Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".
ONE TIME RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
SEQUENTIAL RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed to troubleshooting (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.
Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Built-in Type Yaw Rate Sensor)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Vehicle stability control system DTCs are not output | A |
| Vehicle stability control system DTCs are output | B |
A
B
Clear the DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1AA3 is not output | A |
| DTC C1AA3 is output | B |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
Replace the pre-crash safety city sensor (See page Vehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>REMOVAL).
Perform pre-crash safety city sensor learning.
Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".
ONE TIME RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
SEQUENTIAL RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
NEXT
Clear the DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1AA3 is not output | A |
| DTC C1AA3 is output | B |
A
B