If it is determined that the beam axis of the pre-crash safety city sensor is deviated, DTC C1AA8 is output. DTC C1AA9 is output when the system determines that camera beam axis learning has not been performed or has not been completed normally after a new pre-crash safety city sensor is installed.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1AA8 | The beam axis of the monocular camera sensor or any of the laser sensors built into the pre-crash safety city sensor has deviated. | ·
Pre-crash safety city sensor ·
Windshield glass ·
Wheel alignment |
| C1AA9 | All of the following conditions are met: -
The battery voltage is 9 V or more. -
The vehicle is being driven at 10 km/h (7 mph) or more. -
Camera beam axis learning not been completed. |
·
Pre-crash safety city sensor ·
Pre-crash safety city sensor optical axis learning has not been performed or has not been completed normally. |
When replacing the pre-crash safety city sensor, replace it with a new one. If an ECU which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be output.
If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.
Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".
ONE TIME RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
SEQUENTIAL RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
When replacing the windshield glass of a vehicle equipped with a pre-crash safety city sensor, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the pre-crash safety city sensor may not be able to be installed due to a missing bracket or the pre-crash safety system may not operate properly due to a difference in the transmissivity or black ceramic border.
Pre-crash safety city sensor optical axis may deviate if the vehicle is driven on a banked road, such as a racetrack. This deviation can be corrected by driving the vehicle on a normal road for a while.
Pre-crash safety city sensor optical axis may deviate when the vehicle is overloaded or the wheel alignment (toe-in) is incorrect. The pre-crash safety city sensor optical axis can be corrected by decreasing the load on the vehicle or adjusting the toe-in.
Clear the DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Current DTC C1AA8 is output | A |
| Current DTC C1AA9 is output | B |
| History DTC C1AA8 is output | C |
A
B
C
Check the operating conditions of the vehicle.
| Result | Proceed to |
|---|---|
| Vehicle is overloaded or being towed | A |
| Vehicle is not overloaded or being towed | B |
A
B
Return the vehicle to normal operating conditions.
Perform the "Recognition Camera/Target Position Memory" and "Recognition Camera Axis Adjust" of pre-crash safety city sensor (See page Vehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>REMOVAL).
NEXT
Check the front and rear wheel alignment (toe).
for front wheel alignment:
(See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT)
for rear wheel alignment:
(See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>INSPECTION)
| Result | Proceed to |
|---|---|
| Front or rear wheel is misaligned (toe) | A |
| Front and rear wheels are not misaligned (toe) | B |
A
B
Adjust the alignment (toe) of the wheels.
(See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT)
NEXT
Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".
ONE TIME RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
SEQUENTIAL RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
Check the installation condition of the pre-crash safety city sensor (See page Vehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>INSTALLATION).
If there is a malfunction with the installation condition of the pre-crash safety city sensor, replace the windshield glass (See page Vehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>REMOVAL).
| Result | Proceed to |
|---|---|
| Deformation or deviation in pre-crash safety city sensor installation bracket | A |
| No deformation or deviation in pre-crash safety city sensor installation bracket | B |
A
B
Replace the windshield glass.
(See page Vehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL)
NEXT
Perform the "Recognition Camera/Target Position Memory" and "Recognition Camera Axis Adjust" of pre-crash safety city sensor.
Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".
ONE TIME RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
SEQUENTIAL RECOGNITION
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
NEXT
Clear the DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1AA8 and C1AA9 are not output | A |
| DTC C1AA8 or C1AA9 is output | B |
A
B
Check for DTCs related to misalignment of the pre-crash safety city sensor.
If only history DTCs are stored, they may have stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when Beam Axis Learning was performed.
Clear the DTCs (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR).
NEXT