If it is determined that the beam axis of the pre-crash safety city sensor is deviated, DTC C1AA8 is output.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1AA8 | The beam axis of the monocular camera sensor or any of the laser sensors built into the pre-crash safety city sensor has deviated. | ·
Pre-crash safety city sensor ·
Windshield glass ·
Wheel alignment |
When replacing the pre-crash safety city sensor, replace it with a new one and be sure to initialize the settings. If a pre-crash safety city sensor which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be stored.
If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Pre-crash Safety City Sensor Learning.
Adjustment (One time recognition)
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
Adjustment (Sequential recognition)
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
When replacing the windshield glass of a vehicle equipped with a pre-crash safety city sensor, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the pre-crash safety city sensor may not be able to be installed due to a missing bracket or the lane departure alert system may not operate properly due to a difference in the transmissivity or black ceramic border.
Pre-crash safety city sensor optical axis may deviate if the vehicle is driven on a banked road, such as a racetrack. This deviation can be corrected by driving the vehicle on a normal road for a while.
Pre-crash safety city sensor optical axis may deviate when the vehicle is overloaded or the wheel alignment (toe-in) is incorrect. The pre-crash safety city sensor optical axis can be corrected by decreasing the load on the vehicle or adjusting the toe-in.
Check if the stored DTCs are current DTCs.
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Current DTC C1AA8 is output | A |
| History DTC C1AA8 is output | B |
A
B
Check the operating conditions of the vehicle.
| Result | Proceed to |
|---|---|
| Vehicle is overloaded or being towed | A |
| Vehicle is not overloaded or being towed | B |
A
B
Return the vehicle to normal operating conditions.
Perform the "Recognition Camera/Target Position Memory" and "Recognition Camera Axis Adjust" of pre-crash safety city sensor.
Adjustment (One time recognition))
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
Adjustment (Sequential recognition)
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
NEXT
Check the front and rear wheel alignment (toe).
for front wheel alignment: (See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT).
for rear wheel alignment: (See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>INSPECTION).
| Result | Proceed to |
|---|---|
| Front or rear wheel is misaligned (toe) | A |
| Front and rear wheels are not misaligned (toe) | B |
A
B
Adjust the alignment (toe) of the wheels (See page Suspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT).
NEXT
Adjustment (One time recognition)
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
Adjustment (Sequential recognition)
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
Check the installation condition of the pre-crash safety city sensor (See page Vehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>INSTALLATION).
If there is a malfunction with the installation condition of the pre-crash safety city sensor, replace the windshield glass (See page ).
Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL
| Result | Proceed to |
|---|---|
| Deformation or deviation in pre-crash safety city sensor installation bracket | A |
| No deformation or deviation in pre-crash safety city sensor installation bracket | B |
A
B
Replace the windshield glass (See pageVehicle Exterior>WINDOW / GLASS>WINDSHIELD GLASS>REMOVAL).
NEXT
Perform the "Recognition Camera/Target Position Memory" and "Recognition Camera Axis Adjust" of pre-crash safety city sensor.
Adjustment (One time recognition)
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (ONE TIME RECOGNITION)
Adjustment (Sequential recognition)
Click hereVehicle Interior>PRE-CRASH SAFETY>FRONT SENSOR>ADJUSTMENT (SEQUENTIAL RECOGNITION)
NEXT
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC C1AA8 is not output | A |
| DTC C1AA8 is output | B |
A
B
Check for DTCs related to misalignment of the pre-crash safety city sensor.
If only history DTCs are stored, they may have stored due to a temporarily condition such as overloading of the vehicle, and the system returned to normal when Beam Axis Learning was performed.
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM>DTC CHECK / CLEAR).
NEXT